Saab Aerosystems has a long tradition and a lot of competence in the field of flight simulation. Their ambition to broaden the market horizon has led to a discussion about also selling vehicle simulation solutions, both for military and civilian use.The aim of this thesis is to investigate the driver?s experiences of the accelerations he or she is exposed to whilst driving in rough terrain. The results may be used as a basis for future decisions and can act as a platform for the construction of an effective simulation model.To investigate the driver?s exposure of acceleration, some kind of dynamic simulation is needed.

The issue about how Scania shall perform HVAC tests in the climatic wind tunnel CD7, which Scania is about to complete by year 2013, has resulted in four test methods for truck HVAC and also a test method structure. The test methods have been chosen to focus on sun, snow and rain simulations. These are adapted and developed according to what should be tested and to what can be tested in CD7, which has been the object. With CD7 different climates can be simulated in a controlled environment for complete truck level, from desert with high sun load to arctic cold and snow.The test methods represents a basis to start from, for designers and test engineers which make the testing more repetitive as well as time eventually can be saved. Before the test methods can be applied they must be verified as they are based on theoretical and empirical assumptions.

The exhaust arrangement on a Scania V8 consists of one manifold at each bank connected to a twin entry turbine (8-2-2). A study in GT-Power has shown improved performance and reduced cylinder to cylinder variations using two manifolds at each bank in combination with a single entry turbine (8-4-1). This thesis work analyses the difference in performance shown in simulation and verify it by engine test.The initial work was focused on simulation in GT-Power. Investigating how exhaust manifold volume and pulses effects the turbine efficiency and the mean effective pressure during the gas exchange. To verify GT-Power simulations four engine tests with different exhaust arrangement have been made.The results from GT-Power simulation indicate that a larger exhaust volume improve the turbine efficiency.

This report contains CFD-simulations of cable tray fires in nuclear power plant applications with the CFD-code SMAFS. Furthermore the report evaluates the use of CFD-codes within this kind of problems. The assessment of this report is that there is a tendency towards the good use of CFD-codes but before using it solely more research has to be done on the subject..

In many products a compromise between ground clearance and the required space to store the product has to be made. This problem attracted the attention of the authors of this thesis.The objective of this project is to develop a functioning solution to a foldable wheel. The solution should be applicable to several types of product groups. A limitation for this work has been made so that the work only covers solutions for lighter vehicles.The purpose is to drive this project forward, so that a solution can be found. Furthermore the purpose of the report is to clarify how the authors proceeded to design and construct the wheel according to a fixed specification.

The essay discusses how to look at a equality plan of a academic department experiences the, gender equality in general and how power is portrayed from a gender perspective in the academic department. Through the use of qualitative interviews and a short survey the results have shown that few of the staff members have knowledge about the equality plan and few are familiar with its contents. Furthermore results show that the academic department is run hierarchyilly and that both vertical and horizontal gender segregation exists.The climate at the academic department is characterized by the will to work with gender equality but so far there have only been few exercised or planned efforts to do so. The gap between theory and practise is wide, the will to be seen as an equal academic department concerning equality of men and women seems important. The conscious or unconscious strategy of covering up the real gender equality seems to be done by focusing on the numerical equality..

This report investigates a possible solution to the problem with adapting wave powerplants to work in countries with tidal water. The wire connecting the buoy at the surface with the generator at the bottom needs to adjust to the varying water depth. Our solution to this problem is to attach the wire to a jack which is then placed inside the buoy. The jack is then powered by an electric engine. The report discuss what forces the buoy will be exposed to and then the structural integrity of the design is evaluated through simulations.

This thesis has been performed at Scania CV AB Technical Centre in Södertälje and its aim hasbeen to study the causes and effects of deformations in the interface between the rear axlehousing ADA1100 and the central gear house R780 during operation. Design changes that wouldincrease the sealing capability of the studied interface are also suggested. Finite element (FE)and CAD software have been the primary tools in this study.Finite element (FE) simulations are used in the industry to predict and develop engineeringdesigns. The main motive for FE simulations has traditionally been to identify weak spots in thedesign, regarding high tensions and large deformations.The FE model is an aggregation of submodels and interface models that represents the rear axlehousing, suspension, central gear, central gear housing, wheels, bolts and weldings, and theirinteractions. The submodels have different material properties and they are connected withcontact interface models.Boundary conditions are defined on the bushings in front of the rear axle and on the air bellowsbehind the rear axle.

The Homogeneous Charge Compression Ignition (HCCI) engine is promising in terms of lowNOx, low particulates and high efficiency. Due to its homogeneous charge, where thecombustion starts almost simultaneously from a number of points in the combustion chamber,only lean mixtures are possible to burn because of the resulting rapid combustion, which is muchfaster than the combustion in an SI-engine or a diesel engine. When richer mixtures are used thecombustion will start earlier and also be more violent.To phase the combustion later and lower the combustion speed, external cooled EGR can beused. The EGR-system used in this thesis uses a divided exhaust channel where one channel andits corresponding valve are used only for transporting EGR back to the intake system.Consequently the EGR-valve is connected to the intake pressure. This system is called Direct-EGR (D-EGR).Engine tests verified that the CA50 indeed is phased later when cooled EGR is used.

In many products a compromise between ground clearance and the required space to store the product has to be made. This problem attracted the attention of the authors of this thesis.The objective of this project is to develop a functioning solution to a foldable wheel. The solution should be applicable to several types of product groups. A limitation for this work has been made so that the work only covers solutions for lighter vehicles.The purpose is to drive this project forward, so that a solution can be found. Furthermore the purpose of the report is to clarify how the authors proceeded to design and construct the wheel according to a fixed specification.

The power system modelled in this thesis work has been developed for simulationwhen e.g. the production in some part of the power system is changed. The powersystem has been modelled according to the swing mass of the system, the frequencydependency of the load and the turbine governor. The model determines the systemfrequency, the period of regulation and the power exchange between the differentsubsystems in the Nordic synchronized system.In this model the system frequency is assumed to be the same in all different parts ofthe power system and the voltage conditions in the power system are neglected. Forthat reason power swings does not occur between different subsystems in the powersystem, which usually occur as a result of the swinging connection between thetransmissions line.

Nynas produces bitumen at two refineries in Sweden. The bitumen is shipped to seven depots along the swedish coast line, and from the depots special trucks handle the transportation to customers. Recently Nynas has transformed its supply chain and closed down a few depots. At the moment the company is considering a further reduction of the number of depots. In connection to these discussions an analyse of the companys distributionsystem and of possible changes is required.

This thesis describes a conceptual design of a support frame for a synchronousgenerator used in a vertical axis wind power plant. In this system the generator isplaced on ground level. The thesis also considers the design of housing for thesupport frame and generator. The concept presented in this report is based on anearlier design. Besides geometric design, simplified simulations has been run in orderto optimize some of the parts included in the construction considering naturalfrequencies and structural strength.The result is presented as CAD-models andan assembly drawing..

The purpose of this study is to examine how participants perceive virtual agents shown on a computer display. In particular, it is explored to what extent participants transfer gender and attraction stereotypes that are commonly applied in the physical world to virtual agents. Previous related studies have often explored only text or voice interfaces, without any visually appearing agents, and here indeed found evidence for a transfer of gender stereotypes. Our hypothesis was that the addition of a visual agent interface would reinforce this effect. The results support our hypothesis that participants transfer human gender and attraction stereotypes onto virtual agents, as well as that these processes are affected by the visual representations of the agents..

A problem in the field of district heating is the oil burners needed to provide power when a peak load occurs. One possible way of reducing the needed amount of oil is to reduce the power demand for space heating in the district-heating substations when the need for district heating water exceeds a certain limit. This can be done by use of a locally working controller function.In this Thesis the options concerning load priority are evaluated. To evaluate the potential for using controller functions concerning peak load priority an experiment was brought out in a chosen district-heating substation. The impact on the indoor thermal comfort during a heat reduction was also taken into account.