The focus of this thesis is primarily in electronic construction and describes the design process for a microcontroller circuit board from concept development to prototyping. The client develops test fixtures for automated testing of products within the electronics industry and needs a new controller circuit for the test fixtures that can handle controls and basic testing. An investigation into the needs of such a system is conducted and a prototype printed circuit board assembly is manufactured.The prototype is developed with focus on protection against electrostatic discharges and overvoltage. Among the functions that are included are voltage measurements, communication interfaces and control of input and output currents. Firmware for the prototype is developed and configured to communicate with a PC through USB interface for control and collecting of measurements..

Opcon Powerbox is a product developed by Opcon together with the underlying company SRM (Svenska Rotor Maskiner) where surplus heat from the industry is used through an Organic Rankine Cycle (ORC)?process to produce electricity. An ORC-process is a thermodynamic circle process in which a refrigerant is used as the working fluid. The refrigerant makes it possible for the circle process to operate at lower temperatures than the conventional Rankine process.In this master?s thesis a data analysis software for the Opcon Powerbox has been developed in which measurement data is retrieved and handled from the Opcon Powerbox.

The purpose of this thesis work was to develop an automatic fault detection system for surveillance of bearing temperature in hydropower turbines. The parameters used except the bearing temperature were cooling water temperature and cooling water flow. A simple static model based on data sampled every minute was developed to estimate the bearing temperature. Then a detector for detection of change in bearing temperature based on the CUSUM-algorithm was designed. Since the amount of data was very small the developed model was too uncertain to be used in a working system.The designed fault detection system showed to work well for the available data.

This report describes an bachelor thesis work which is performed in cooperation with SVIA that develops and sells automation solutions for the manufacturing industry. The thesis purpose was to evaluate the machine FeedLine to find opportunities for improvement in the product?s design that could lead to more standardization and thus improving the efficiency of manufacturing and assembly.Based on these basic issues suggestions for improvements were developed:How can the design of FeedLine be improved to facilitate the assembly?Can more standardization be imposed on FeedLine?s design to enable more stocking of standard components?An initial pre-study was conducted to evaluate FeedLine?s to find opportunities for improvement in its overall design. During the pre-study staff at SVIA and two of its clients was interviewed. Based on information gathered during the interviews and observations by the authors improvements was amendments.

Lumilos is a work investigating the possibilities to use light and color in an interactive design context. I have explored different light sources and compared them to each other and given a short description of the history of light and how it has been developed during the industrialization in the western world. I have also investigated what is currently done in the field and summarized that with examples in the categories passive-, colored-, material- and interactive light. The conclusion is that working with interactive color and light is a hard task. There are many different angles to take into account such as personal likings and earlier experiences that is uncontrollable by the designer. Yet there are many possibilities and light is a material that is moldable in many forms. I have put the knowledge about light and color into practice and developed an interactive light wall that is visualizing energy consumption with the use of different colors of light and animations.

Stadsförnyelse i innerstadsnära läge. Utarbetning av en strukturplan för stadsdelen Rothenburgsort i Hamburg.

Since the spring 2003 the tenant-owner home association the Terrace in Upplands Väsby municipality lies straight under the approach route to Arlanda Airport?s new third landing chute. Noise levels of over 70 dB have been measured in the area, which exceeds National Board of Housing?s, values for traffic noise at a terrace in connection to housing. By using the method of hedonisk pricing the essay tries to find out if there exists a willingness to pay to reduce the noise in the area.

Examensarbete om moderna husbåtar med Sverige som utgångspunkt. .

The aim of this study was to compare activity, lying down and getting up behaviour, weight gain and cleanliness in heifers in cubicles versus on deep-litter. The study was conducted from autumn of 2005 until autumn of 2006 in a commercial organic dairy herd with 340 cows. In 2005 the farm rebuilt half of the young stock accommodation from deep-litter pens to cubicles. The experiment used 150 heifers of the breeds Swedish Red, Swedish Holstein and crossbreeds between these, all born on the farm. The animals were divided into three blocks based on breed and within each block they were sorted after increasing age. The youngest heifer in each block was randomly allocated to one of two groups, cubicle or deep-litter pen.

The purpose of this thesis is to present and describe which criteria, according to the systemfamily Configuration Management, should be met when developing a CM-tool to handlemigration data.ACT is a tool developed by Microsoft to gather information about, analyze, test and mitigateapplications in a network when migrating the IT-infrastructure of an organization to a newoperating system. The organization that is being studied wants to present the data about theanalyzed applications in such a way, that a customer can choose what to mitigate and migrate.The goal is therefore to develop a prototype (CM-tool) that will present this data.The study has shown that ACT lacks certain requirements stated by the organization when itcomes to presentation. But when it comes to the rest of the functions, ACT performs as expected.The investigation resulted in specifications and technical solution for the new CM-tool. CMcriteriafor migration data was put forth and parts of the prototype were also developed..

This thesis concerns to investigate renovations of existing buildings aiming at enabling energy efficiency, from a conservation and restoration perspective. This includes performing case studies of three projects in the Gothenburg area where renovations has been done and an analysis of directives raised by the EU and later implemented by the Swedish National Board of Housing, Building and Planning, Boverket. In addition to these, regulations enforced by the Swedish law, related to the topic, have been considered.The investigated projects in this case were the housing cooperative Välten in Brämaregården, the Solar Buildings in Järnbrott and Gårdsten as well as Katjas Gata 119 at Backa Röd. In order to measure and compare the results of these projects a comparison between the pre- and post-restoration energy consumption have been performed. To capture additional perspectives the grading system Operation Kungsörn has been applied.Regarding the comparison of energy consumption the renovation of Katjas Gata 119 was found preferable but showed in my view lacking attention to the cultural heritage of the area.

This report describes the development and implementation of a system for transmitting digital information at high speeds from a miniaturized submersible developed by the Ångström Space Technology Centre at Uppsala University. For instance, the vehicle shall transmit image data ? even stream live video - through an optical fibre to a monitor in a ground station. Hence, the system shall be used both to convert the image data to make it transmittable, and to recreate it at the receiver.The work includes a pre-study of the programming language and the technology used. A concept for the solution is presented together with main components later broken down into internal functions.

This thesis was performed at Vendig AB which is a company that develops and sells products such as belt scrapers for conveyor. The thesis is divided into two parts, one part where it´s investigated which tension force is required to tighten Vendig AB´s scraper Hampus against the belt in a correct way. The second part is called mechanical design and here a new and more compact tension device is developed.Field studies has been conducted at a couple of Vendig AB´s costumers to get a knowledge base about how Vendig AB´s products are used, how they function and the environment they operate in. During one of the field studies the force between the scraper and the belt was measured. The result from the measurements, together with a report from LKAB [1], were evaluated and summarized in a table.

Determinants of Small Housing Prices in Stockholm 1993-2009, is an econometric study. Regression analysis is used to identify and measure the dominant factors that determine small house prices in Stockholm. Economical fundamenta and neo-liberal varaibles are in use to explain nominal overprices in the house market, as well as the steady development of real house prices in the region..

This master?s thesis describes the development of a model of the catalystsystem aiming at control by an MPC. A well functioning model, which is suitable in control purpose, is important while emission legislation become more and more hard to fulfill for the car manufacturers. Much research has been done in the field of physical modeling of the system, but in this work a linear adaptive time discrete ARX-model is developed and validated.The systems tendency to change its dynamic during usage implies that the model must be adaptive. The developed model proved to be well functioning and shows promising conditions for the MPC design.