The objective of this study is to examine how Lean can make the utilization of inventory more effective and, from a Lean perspective, examine how the value-adding activities related to inventory can increase. To examine this, a case study was perfomed at Svenska Fönster. The conclusions of this study are that Lean can advantageously be applied on inventory to increase the efficiency. .

The primary function of a mixer is to keep a fluid in constant motion. All mixing applicationsrequire varying degrees of small-scale turbulence and bulk flow. The performance of asubmersible mixer is measured by the thrust that it produces, while the strength of the bulkflow is dependent on the total amount of installed thrust.In a mixer, the fluid quickly flows past the propeller, and as a result, the current is mainlyaxial. The fluid will also obtain a rotating velocity, or a swirl, though this is significantly lessthan that of the propeller. During the process, the total amount of energy increases in the formof static pressure and kinetic energy.

Aeroseum is an aviation museum located in an old military underground hangar. The ventilation system in the hangar is designed for the military purpose of the hangar. This design includes a solution with air flowing through the space between the construction of the hangar and the rock surface. The solution is intended to avoid a buildup of inflammable gases. This design leads too high humidity levels in the hangar.

This paper aims to, through a literature review, examine how to best design and adapt calf huts to meet the calf's physiological requirements and reduce the infection pressure for enteric and respiratory diseases. It illuminates how the calf relates to different temperatures and climate, which temperature control mechanisms it uses and its ability to perform these regulations, as well as providing a summary of the past decades´ research on the calf huts housing system. These two theory chapters, along with a concluding discussion, provide a better understanding of how to, especially in temperate climates, design the most suitable calf hut, which cater to the calf's both thermal comfort and physical health. The literature suggests that the calf's own temperature control works well to counteract the temperature outside the desired range, and that one of the most important factors rather is ventilation of a calf hut, which reduces moisture and pathogens. The conclusion of this paper is mainly that there is not an obvious way to place and construct a calf hutch and that most design principles contribute to both positive and negative effects simultaneously.

There is a need for productivities data and data for different types of machines for comminution of logging residues. The lack of data and studies on GROT comminution makes it difficult to evaluate different chains for handling of residue fuels and make system analyses.Four types of machines with three different working principles were compared at six studies during winter conditions. Three to eleven trials during 9.5 to 30.7 minutes were made on each machine. Samples from the produced material at each study were sieved to determine the size distribution of the comminuted material. Samples were also taken from the studies for determination of moisture content.

The ISO 9000-series is a set of quality standards created by the International Organization for Standardization. The series is intended to provide guidance to companies in the process of deploying an effective quality management system. The series includes the requirements standard ISO 9001. This standard contains requirements on how a quality management system should be designed and how companies generally must work with quality issues. When a quality management system is introduced, if wanted, a quality certification can be implemented.

The task was to design and manufacture a submersible displacement pump working with the wobble plate principle. The main task for the Wobble plate pump is to be used as a sewage pump for smaller households or dewatering pump in environments where small flows and high pressures are acquired. For these purposes ITT Flygt sell a screw pump, PC-Grinder 3068. The hydraulic part of the PC-Grinder is manufactured by a subcontractor. Therefore ITT Flygt wants to evaluate an alternative to their screwpump PC-Grinder, which can be entirely manufactured by them self.

Fuel pellets are a refined bio fuel mostly consisting of residues from sawmills and wood industry. At Rindi Västerdala AB's combined bio energy plant in Vansbro fuel pellets are produced, while the waste heat from the process is used for district heating. The pellets are produced from sawdust, wood shavings and dry wood chips that is dried, milled and pressed into small cylindrical rods. The advantage of refining the wood material in this manner is that the energy value is greater per unit volume and unit weight, thereby the cost of transportation per energy unit is reduced. Also, less storage space is needed.Pellet manufacturing is a complex process since many parameters affects the final results.

The production of oilseed rape is an important issue in Sweden and those who never have grown oilseed rape (OSR) are now willing to try. It is always a risk to grow oilseed rape, specially winter OSR, because of outwintering. This risk increases as you go north and therefore establishment and autumn growth is very important. These are some of the reasons that I have chosen to write about the establishment of winter oilseed rape in Middle Sweden. There are many factors that influence the outcome of the establishment, e. g.

Sweden is a country that has made some progress in developing energy efficient solutions. The problem in Sweden is that many houses and apartment buildings are old and have inefficient ventilation- and heating systems. This energy is lost when systems are inefficient, which then results in huge economic costs. Luckily, more and more people are becoming aware of this, which means that Sweden is on track to become even better within energy efficiency.Energy use for the housing- and service sector amounts to 166 TWh of total use at 616 TWh. Without distribution and conversion losses, these figures show that the housing- and service sector accounts for almost 40 % of the country's total energy consumption.

The aim of this bachelor thesis has been to investigate some of the materials present in and onprinted papers which might be suitable for analysis. A brief history of paper making and somepigments were studied after which the theory of some of the available methods for technicalanalysis were summarized. Two works of art on paper were chosen for a closer examination,both are woodblock prints but of different composition and origin. The investigation wasmade to exemplify some of the common techniques applied on works of art. There were twoaims in these examinations.

This thesis purpose is to determine an explanation of the efficiency in a labour-market related project. ?Enter? is an EU-financed project with a focus on long-term unemployed workers in the district Härlanda, Gothenburg. Starting in September 2004, Enter offers individually based coaching and job guidance to totally 110 young persons with problems entering the labour market. The goal is to provide these people courage to find either full or part time employment or to start study.

Aeroseum is an aviation museum located in an old military underground hangar. The ventilation system in the hangar is designed for the military purpose of the hangar. This design includes a solution with air flowing through the space between the construction of the hangar and the rock surface. The solution is intended to avoid a buildup of inflammable gases. This design leads too high humidity levels in the hangar.

The investigation was initiated because of the high workload of the sellers and, additionally, because the Tunadal sawmill has received low ratings in customer surveys. Thus,  two main approaches are adopted here,  the first being to investigate which of the three methods  of working, namely, market divided flow organization, function organizationand flow organization with collaboration, proves to be the most beneficial. The second is to investigate whether there is an available method to ease the daily work. A literature review has been made in order to determine more efficient ways for the sellers to work in the Tunadal sawmill. During the investigation, an in-depth investigation into the total quality management using a balanced scorecard as a management tool was conducted.

In this report we describe an adaptive simulated annealing method for sizing the devices in analog circuits. The motivation for use an adaptive simulated annealing method for analog circuit design are to increase the efficiency of the design circuit. To demonstrate the functionality and the performance of the approach, an operational transconductance amplifier is simulated. The circuit is modeled with symbolic equations that are derived automatically by a simulator..