This report is a documentation of the workflow and the result of a project carried out by twostudents from the Royal Institute of Technology in collaboration with a company. The report isstructured in a chronological order and describes the methods and systems developed in theworkflow. The report shows how the project evolved from a study phase to the various proposals onthe concept solutions.The project aims to develop a systematic way of bonding two different kind of cardboard under fiveminutes. By conducting a general study about glue and its different forms it was possible to obtain abroad knowledge, which helped to choose the right substances to later use in testing on the differentcardboard materials in question. Glues's survey resulted in a list of different substances that wererelevant to the project.

The background to the study is that within the next ten years about 50 new multi-purposeindoor arenas will be built. These are used for various events such as sports, concerts, etc. In order to achieve a high level of security in the case of danger alarm signals and alarmmessages must be heard well by the visitors. ÅF-Ingemansson wanted to show builders the importance of good speech perception and that it is not observed in arenas today. They conducted technical tests on two large multi purpose indoor arenas to develop parameters that affect speech perception in the arena.To get a subjective view of how these arenas are experienced a survey was created.

Shock absorber units play a key role in establishing the driving dynamics and performance of automobiles. Öhlins Racing has manufactured high-tech automotive shock absorbers for over 30 years. Öhlins Racing?s advanced technology has contributed to over 200 world championships in automobile racing. Öhlin?s manufacturing process has long utilized automated fluid filling equipment during the final shock absorber unit assembly stage. The filling process consists of vacuum pumping the shock absorber unit and subsequent transfer of fluid. Vacuum pumping is necessary to remove residual air from the shock absorber unit prior to initiating the liquid filling stage. The presence of undesirable gases drastically compromises the performance of a shock absorber. The filling degree, defined as the final ratio of air to oil, is determined by the specific filling protocol as well as the specific equipment utilized.The current investigation aims to develop a viable technique to accurately determine residual air content in shock absorber units. If the filling degree can be appropriately quantified for a specific manufacturing process, then the air/oil ratio may be quantitatively related to shock absorber performance. The utilized measurement method must be completely integrated into the manufacturing process to guarantee shock absorber performance specifications according to the manufacturer?s standards. By utilizing the measurement method developed in this work, the manufacturing process, manufacturing equipment and product specifications can all be tailored to provide improved filling conditions.The developed measurement method provides accurate quantification of the filling degree under a wide range of processing conditions. The method establishes the relative quantity of air in the shock absorber unit by performing in-situ compressibility tests. The fill ratio can be controlled and varied by manipulating the vacuum pressure exerted during the filling process. Performance tests, however, indicate no correlation between filling degree and unit performance..

What psychologial processes are activated in experiencing mourning after a loss of a belovedperson? How is death described in other authors? novels and short stories compared to mine?This essay aims at analysing my two short stories The follower and The price for love fromdifferent aspects. I discuss the psychological realism and the spirituality using the method ofclose reading, interpreting and applying ideas of texts from other authors in my short stories.Death is a central phenomenon in both of my texts. Therefore I discuss death frompsychological and philosophical aspects in this essay. To get a philosophical frame of death Iturn to Jacques Derrida, Emmanuel Levinas and Martin Heidegger.

This thesis was performed at Indusec ABin Stockholm. Indusec AB is a companythat develops security solutions.Together with the Police of Sweden theyhave gotten the assignment to develop anapplication based on one of theiralready existing product Inferno soundbarrier. This application is supposed tobe mounted on a ballistic shield thatthe police use, the application consistsof a speaker box (the sound barrier) anda trigger with wire. The trigger withwire is the part that will be addressedin this thesis. The application willthen be used as a tool to surprise atarget at various skirmishes.The project consists of three majorphases, pre-study, concept generationand modeling.

The purpose of this paper was to investigate whether Suzanne Retzinger?s linguistic cues for shame and verbal behaviors for hiding shame could be used to measure shame in surveys based on Thomas Scheff?s theory of shame. I created a measurement instrument consisting of 30 statements, which were all meant to measure general shame.The instrument was administrated to 180 respondents studying at Karlstad University, of whom 4 respondents were removed from the data set due to lack of standardization. With the polytomous rasch model used for the analysis, data from 176 respondents were analyzed, of whom 124 respondents were female and 52 were male.The result showed that the measurement instrument?s statements should not be used together because the analysis indicated multidimensionality.

The student project Elba at KTH started in 2011 and is a project where a battery driven prototype car is developed. The vehicle competes in Eco Shell Marathon in Rotterdam, Holland. In this competition the vehicle that travels a certain distance including several starts and stops with the lowest energy consumption wins. To minimize the consumption is therefore very important, which requires knowledge of the vehicles energy losses.A vehicle's energy losses depends on several factors and can be divided into the powertrain efficiency and the driving resistance. The driving resistance can then be divided in to rolling and air resistance, if smaller losses like vibrations are ignored.

The environmental debate is more intensive than ever before and the demands on companies increase. There are a number of methods to make it easier for the companies to fulfil the demands. Life Cycle Assessment (LCA) end ecodesign are some of the methods that can be used. Syntronic AB has the possibility to reduce the products´ environmental impact in the design phase. Therefore it is important for the company to make it possible to visualize the negative environmental impacts a product can cause in an easy way. It is also important to visualize for there clients if any improvement is possible. The purpose of this thesis is to develop a simplified model.

Catecholamines are stress hormones that are produced and released by a rare tumor called pheochromocytoma. This tumor can cause hypertension which if undiagnosed and untreated leads to death. Since good therapy is available, it is important to find the tumor in time. The most common way to diagnose the tumor is measurement of the biochemical markers; catecholamines and their metabolites, methylated catecholamines.After observation that almost all normetanephrine results for women were higher than the upper reference limit and therefore pathological, the accuracy of the present reference intervals was questioned. Therefore new reference intervals for both urinary catecholamines and methylated catecholamines were developed by analysis of 46 samples using HPLC.

An often encountered problem when implementing a mass flow regulator in a rolling mill is the one with measurement of speed. The most widely used solution is to fit a pulse counter to a wheel that is in contact with the strip. Common problems with this design are for instance scratch marks on the strip and problems with the flatness measuring system.  One way of circumventing the aforementioned problems would be a non-contact measuring system. The market of today only offers systems based on the Doppler principle.This report evaluates three different systems for non-contact speed measurement. Important areas in the evaluation have been the ability to operate under normal rolling conditions, integration in existing control system and how well the sensor can be fitted to the rolling mill.

An often encountered problem when implementing a mass flow regulator in a rolling mill is the one with measurement of speed. The most widely used solution is to fit a pulse counter to a wheel that is in contact with the strip. Common problems with this design are for instance scratch marks on the strip and problems with the flatness measuring system.  One way of circumventing the aforementioned problems would be a non-contact measuring system. The market of today only offers systems based on the Doppler principle.This report evaluates three different systems for non-contact speed measurement. Important areas in the evaluation have been the ability to operate under normal rolling conditions, integration in existing control system and how well the sensor can be fitted to the rolling mill.

MYDATA automation AB is one of the leading companies in development of surface-mountingtechnology and stencil free solder paste applications. MYDATA?s MY500 is a jet printerdesigned for solder paste application on printed circuit boards. The jet printer contains a cassettewhich consists of a holder and a cartridge. There is also a calibration unit which monitors andcalibrates the application of solder paste.

Social and emotional learning is getting more and more common to work with in Swedish schools today. That has made it more actual to do studies of how you best can implement a method in health prevention and promotion in schools and how you do for to keep the work sustainable. There are some American studies that describe implementation of methods in schools and a few studies that describe implementation of methods for social and emotional learning in schools. It is important to see implementation as a process and not as an individual event. The process never end but continues as a cycle in three phases; readiness phase, planning phase and implementation phase.The aim of this study was to describe teachers and principals experiences of obstacles and possibilities at implementation of an evidence based program for social an emotional learning in compulsory school as a part of the schools health promotion activities.

The environmental debate is more intensive than ever before and the demands on companies increase. There are a number of methods to make it easier for the companies to fulfil the demands. Life Cycle Assessment (LCA) end ecodesign are some of the methods that can be used. Syntronic AB has the possibility to reduce the products´ environmental impact in the design phase. Therefore it is important for the company to make it possible to visualize the negative environmental impacts a product can cause in an easy way. It is also important to visualize for there clients if any improvement is possible. The purpose of this thesis is to develop a simplified model.

The purpose of this study is to show the technical building requirements for modern arenas inSweden. The study will also create an understanding of how the requirements affect theSwedish football arenas which are affected by the regulations valid from 2014. As one of theSwedish football arenas there is Örjans Vall located in Halmstad. The aim of this study is todevelop alternative solutions regarding the technical problems Örjans Vall is facing 2014,when the new arena requirements for ?Svensk elitfotboll? are taken into use.