Our Bachelor´s Thesis has been performed in co-operation with Bors Automation & Tool AB.Our task was to develop a servomotor powered tube cutting-machine with initial point fromtoday's hydraulic driven tube cutting machine Bors HYD 23. The purpose with the newconstruction was to achieve a more power-efficient tube cutting machine which could lowerthe power consumption, and also meet the market continued growing demand forenvironmental-conscious production.Bors Automation & Tool gave us relatively free hands in order to enable new thinking ideaswithout following their traditional constructional solutions.Our solution resulted in a construction based on a power source existing of a servomotordrivenrollerscrew, witch provides a more rational use of energy compared with the currentmethod.Bors Automation & Tool AB has decided to fabricate a prototype of Bors E 23 during theautumn of 2007, which they are planning to revile at the Tube 2008 exhibition in Düsseldorf,Germany.NOTE:Due to an agreement signed by the authors in the beginning of this project, no appendix is published at this time.If you want to wiew these documents, please contact the authors..

This master thesis is performed at Scania Axles and Gearboxes, a production plant located in Södertälje. Within the plant axles, gearboxes as well as central gears are assembled from components to finished products. All production is conducted on production lines, with a pre-determined rate, which is supplied with components by the material handling department. Since the production quantity and the mix of product variants produced on the production line is customer order-based, the number and type of components needed for production as well as appropriate staffing within the material handling department is difficult to predict. Scania is currently using a number of different resource planning tools for each material handling-department within Axles and Gearboxes to visualize the workload within the departments.

The last few decades the development in the field of electronics has been huge. The components performance gets better at the same time as the manufacturing cost decreases. Many of the design moments that have to be done, are done automatically today, but it can get better. Especially for analog circuit design.At Electronic System in Linköpings universitet, research is in progress to develop a tool that can design analog circuits in reasonable time. It means that it has to size the components (transistors, resistances, capacitances etc), so that the circuit can fulfill the performance requirements.

Purpose ? The purpose of this thesis is to develop a total cost model for container transports and create a tool that calculates a suitable transport quantity from an economic view, which fulfills the demands on delivery service. To achieve this purpose the following questions will be answered:Which costs are affected by the decision between the two transport alternatives LCL and FCL?   How does the decision of sending product LCL or FCL influence the delivery service?  How can a tool be constructed to simplify the decision-making process regarding the choice of sending products LCL or FCL?  Method ? A total cost model was developed. This model is supported from existing literature.

ISO14001:2004 : A Human Ecological Tool?This is a study by means of litterature analysis and personal experience to find out wheather you could call ISO14001:2004 a Human Ecological tool. The ISO14001 is an environmental management system. I'm approaching the issue from a users' perspective and putting my experience of implementing the ISO 9001 at my work to good use. Though my personal experience is limited to the implementation of the ISO 9001, it is quite relevant to the task since the update of 2004 the ISO14001:2004 is brought closer to the ISO 9001 standard in many ways.

The new media landscape is growing by the minute with blogs, web pages and different communities. The latest phenomenon that has grown rapidly throughout the world is Facebook. This is at new platform for communications where individuals can meet and socialise. Even political actors have started to appear on this community to work and spread their opinions. Several of the Swedish political parties are represented with different group, among them we have the two biggest political youth organisations: MUF (Young conservatives) and SSU(Young socialists).This study examines how Facebook can be used as a tool to create opinion.

Title: Social media as a communication tool - A case study on social media influencecorporate cultureLevel: Final assignment for Bachelor degree in Business and EconomicsAuthor: Jessika Klintsbacka & Oskar BergeSupervisor: Pär Vilhelmsson, Ernst Hollander & Maria Fregidou-MalamaDate: 2014-06-13Purpose of Study: The aim of this study is to inquire into Swedish companies internalcommunication, their approach to social media as an internal communications tool, and if itaffects the corporate culture.Method: The study is a multiple case study with a qualitative research design. The study'sinterview questions were designed by a operationalization of based on theory in the areas ofinternal communication, corporate culture and social media. The interviews took place inApril 2014. The interviews were recorded and then analyzed to bring out the similarities anddifferences between the companies.Results & Conclusion: The study shows that Swedish companies corporate cultures haveconnections with internal communication, and implementation of social media as acommunications tool. The study found that connections to companies with a comprehensiveone-way positive consider social media as alternative communication tool to strengthen theunity and community within the company.Suggestion for further research: One of the study's three companies is owner-led and thiscompany showed a high level of corporate culture.

Gender mainstreaming has been an internationally dominant policy since the mid 1990?s. In 2004, the Swedish government decided to implement gender mainstreaming within the Government Offices of Sweden. However, little research seems to have focused on the reasons for an organization's decision to implement gender mainstreaming. Consequently, the purpose of this study is to answer the question why the Government Offices of Sweden have decided to use gender mainstreaming.

The aim of this thesis is to study how librarians in Swedish libraries perceive the task of mediating fiction. What are the librarians private relationships to fiction and how do they perceive the position of fiction in contemporary society? What views have they developed of the borrowers approach to fiction and how do they perceive the borrowers increasing influence in the library? How do librarians prioritise and which principles form the basis for their purchase of fiction? How do they categorise fiction in the library and how much do economic and political factors influence the decision making process for the purchase of fiction? Finally, how do they define their roles as mediators of fiction and which strategies do they adopt to communicate which literature the library has to offer? The material used in this study was acquired using a qualitative interview technique in which six librarians with experience of literature mediation partook..

The Master Thesis work this report is based upon has been conducted in cooperation with Svea Teknik AB. Svea Teknik is a consultant firm which is developing parts of a tunnel boring machine on behalf of Atlas Copco. The machine is being developed to mechanically excavate hard rock by fixating itself in the tunnel and then press a large rotating cutter-wheel equipped with disc-cutters against the tunnel wall. The disc-cutters are the tools that are in direct contact with the hard rock and are therefore exposed to extensive wear and needs to be replaced on a regular basis.The purpose of this Master Thesis has been to develop a service equipment that will enable time effective and safe changes of disc-cutters. The disc-cutters have a diameter of 17 inches and weigh about 130 kg.

Den här rapporten beskriver ett examensarbete för högskoleingenjörsexamen i datorteknik vid Växjö universitet. Vid företaget BSR i Växjö pågår utvecklingen av ett diagnosverktyg benämt BSR Diagnostic Tool. Syftet med projektet är att kunna använda en hårdvaruklass som kommunikationsdel istället för diagnosverktyg från de olika biltillverkarna. Inom objektorienterad programmering är en klass ett avsnitt programkod som samlar en mängd relaterade attributer och funktioner för ett objekt. I rapporten beskrivs implementeringen av hårdvaruklassen samt tillhörande teori för kommunikationsbussen som används, nämligen CAN.

Public participation is a key aspect in the planning of Swedish municipalities. It is probably the most important tool of them all in the planning towards a sustainable future within the cities and the municipalities as a whole. Participation from the public can take on several different forms. In this paper I focus to research and discuss in and around the usage of a web-based 3D platform called City Planner. The tool allows the user (the public) to view the municipalities planning in a fairly new (but quickly growing) environment.

In today?s society more and more activities are digitalized. This means that everyone has to be able to use information and communication tools (ICT) in order to take part in the digital world, otherwise they will be left out of the digital community. There is a so called digital gap between for instance elderly and young people, where elderly do not know how to use the tools and there for cannot gain access to the digital society. What happens when people, not only grow old, but also have a communication disorder, such as aphasia? How are they included? The purpose of this study is to investigate whether or not surf pads are good tools for bridging the digital gap for people with aphasia, and which activities and situations that encourages people with aphasia to work with the surf pad.

ABSTRACT Title:                                                Retargeting- When display advertising builds                 loyalty Authors:                                           Mikaela Johansson och Anna Svensson Kjällberg Advisor:                                           Thomas Helgesson Level:                                               Bachelor´s in thesis in Marketing, (15 Swedish       credits) Spring 2014. Keywords:                                        Retargeting, branding Question:                                                    In branding, how should small e-enterprises            work with retargeting? Purpose:                                           The purpose with this essay was to identify how    retargeting should be used in small e-enterprises                             when branding. This was done by comparing two e-enterprises practical use of retargeting, with two                           brand consultants and two retargeting consultants theoretical knowledge within each expertise.   Method:                                            A qualitative method with a deductive approach    has been used to answer the problem statement.  Theoretical framework:                              Earlier theories about retargeting, brand building    and recommended practices, related to marketing                       on the internet, were presented in the frame of       reference. Empirical framework:                                 Primary data were presented by two respondents   representing each area: Companies, Retargeting                        consultants and Brand consultants.Conclusion:                                                   The          marketing tool allows companies and      their               brands to get the chance to appear in                        wide area                      networks on the internet.    The tool is primary used                                                                for a sales                      purpose but the tool also has potential in brand-                                                                       building purposes.

This thesis has treated a three-axis robot which task is to serve a larger test machine tomove the modules to be tested, from the storage to the test site. The robot is composed ofthree linear actuators; two standard components of ball screw type and a custom-builtactuator of trapezoidal type. The work has mainly focused on the custom-built device to seeif it could be replaced with a standard component. Part of the work has been to look into thepicking tool and to see if there are any possibilities to improve its function.The report presents two different proposals which I decided to call Robot 1 and Robot 2 andthey aim to address the problems arising in the purpose-built linear unit and the X-axislinearity problems. Robot 1 focuses on eliminating the problems that arise around therobot's X-axis, with such simple means as possible and without making excessive materialchanges.