Due to an increased population in cities the need of densification of cities increases. This means that the amount of ecological elements in the city is at risk of decreasing. Ecological services contribute to the city?s climate by softening the negative impacts that densification of cities means. Thus increases the will and ambition in city planning in to preserve greenery.This is an interdisciplinary thesis within the subject of geography that studies Biotope Area Factor (BAF), a planning tool that is used in city planning with the purpose of compensating for lost ecological services associated with new housing estate.

Stabilization of subgrade is an internationally common technique to improve the characteristics of a soft soil. Improving the stiffness and bearing capacity of the subgrade enables the pavement to be designed with reduced depths of subbase and basecourse aggregates. This makes the stabilization technique both economically and environmentally interesting. Both natural and stabilized soils have high inherent property variability that should be considered when the characteristic value is derived. By analyzing the spatial variability in stabilized and natural subgrades it is possible get the parameters needed for reliability?based modeling of soil properties.

To design new and high tech products the engineers rely more and more on computer based simulations to investigate the properties and behavior for a component or system.To verify these computer based simulations the dynamic properties for the components of the drivetrain needs to be verified. Therefore measurements of the stiffness and vibrations for the rear axle has been performed. This report show how the measurements has been implemented and evaluated, along with some interesting results for the rear axles properties.The static stiffness for the drive shaft along with the axle-gear has been determined. It is found that the stiffness for the whole rear axle is near the stiffness for the drive shaft, which means that the drive shaft becomes the dominant component of the system and affects the rear axle stiffness the most. The measured stiffness of the driveshaft is close to its theoretical stiffness.The stiffness for solely the hypoid-gear have been calculated using the stiffness for the rear axle and driveshaft, and thus has a range for the stiffness of the hypoid gear been determined.The backlash for the whole rear axle and for some individual components has been determined, where the backlash between pinion and crown-wheel has negligible impact on the total backlash.Measurements of the crown-wheel and pinion movements have been conducted, where the direction of movement is consistent with the theoretical direction of the forces.The vibration measurements show that the vibrations are more severe at certain rotational speeds.

The aim of this thesis is to analyze children?s picture books regarding whether and in what form gender stereotypes can be seen in these. The purpose is also to evaluate whether the findings correlate to the different regulatory documents libraries have to abide to.       The study comprises five books, who are part of a selection of books especially chosen by Uppsala City Library to be used by primary school children aged 6-9. The method used is the study of text as well as illustrations, as the theory of this thesis is that the two cannot be separated, but has to be seen a unit. Other theories used in the analysis include Nikolajeva?s schedule of male/female properties and theories on gender.      The result of the study shows that gender stereotypes are in majority regarding the characters in the books, but that the opposite also exists.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The purpose of this report is to collect, compile and complement the scientific and experience based knowledge concerning high pressure fire fighting today. The goal is to produce a decision data for the Rescue Service concerning the use of high pressure systems for fire fighting. Focus is on hose reel high pressure systems but other systems are discussed too. The report begins by describing the technical properties of the different systems. Then the fire fighting properties are evaluated, including manoeuvrability and safety for users.

This paper has evaluated a new type of prosthetic foot, X-Balance, which aim was to facilitate the performance on uneven ground for the user. This study have performed gait analyzes with three prosthetic feet, the X-Balance, Flex-Foot and assure Ottobock9192 on flat and uneven surfaces using 3D analysis system QTM (Qualisys Track Manager) and associated force plates. During the project a prototype of a design that can perform a mechanical gait were manufactured. The prototype has then been used to fulfill the purpose and objective of this study which is to make different final sets that demonstrate differences between prosthetic feet. Gait analyses of individuals have also been performed to get an idea of what normal gait is.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The global Positioning System (GPS) provides location and time information as long as there are unobstructed lines of sight to four or more GPS satellites. However, when this is not the case the signal may be inaccurate or sometimes even completely blocked. In these situations the Inertial Navigation System (INS) is an appropriate choice for positioning.  An INS has already been proposed in a previous thesis by Erik Andersson and the objective of this thesis is to fuse the GPS with the INS in a proper way. A part of this project is to decide the reliability of the GPS.Three methods for GPS reliability detection have been proposed. One method based on the statistical properties of each of the separate systems, and two methods based on the statistical properties of the residuals between the GPS and INS.

Swedish listed property companies report their investment properties under the standard IAS 40 that gives the opportunity to value investment properties to either historical cost or to fair value model. One problem with the fair value model is that there is no observable market price since the real estate market is far from complete which means that the price of the asset is hard to determine because of the limited information.IAS 40 gives companies the opportunity to choose between internal or external valuation and this study aims to show how the property companies? values appeared between the years 2007-2011. From the result we will study if there could be a difference in the outcome depending on if the company chose either internal or external valuation.To investigate this we observe all Swedish real estate companies listed on OMX Nordic Stockholm and their financial reports during this period of time and complement this information by interviewing people working with these matters in the property companies. The methodology for the study is therefore partly quantitative and partly qualitative since we collect data both from financial reports and from interviews.

The purpose of this work is to find out if the suctionvalve to the salivaejector for dental equipment in a simple way can be improved or if a new design is needed. The result of the examination of the suctionvalve shows that the friction between the piston and the seal is high and that this causes the valve in a few cases sheaves. The study concluded that only small changes in material or detail, improve the component..

Arbetet redovisar möjligheten att parametrisera 2D-ritningar hos Solyvent Fläkt AB. Flertalet koncept har utvecklats och det mest lämpade konceptet har valts ut genom en konceptjämförelse där konceptens för- och nackdelar har vägts mot varandra. Konceptjämförelsen har slutligen presenterats för företaget..

Det här examensarbetet har genomförts i samarbete med Metso Dynapac AB i Karlskrona. På deras asfaltsvältar finns idag olika modeller av körspakar. De har samma grundfunktion och bör kunna samordnas till ett gemensamt reglage. Detta ger möjligheter att använda rationell tillverkningsmetod p.g.a. volymen.

An energy study has been performed on two blocks in an area called Gävle Strand. The buildings are owned by a tenant-owner?s association called brf Carolina and were built by the company Skanska 2008. The builder as well as brf Carolina are pussled by the fact that electricity use is higher than expected while heating is less. Skanska is also very interested in finding out how much heat recovery from stale exhaust air through a geo-thermal heat pump is contributing to the general heating requirement and energy balance in four out of the ten buildings located on the properties.To find possible answers to the higher electricity use a literature survey on user behaviour was conducted.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..