The aim of this study is to evaluate whether the value of occupant load is over or under estimated when the Swedish general value for department stores, 0,5 person/m2, is used for dimensioning shopping centers. The data that was analyzed derives from seven shopping centers and one department store. A conservative method was used to calculate the occupant load factor. The analysis shows that two groups can be discerned: one group that is characterized by a lower occupant load factor that does not exceed 0,3 person/m2, and one group with a higher occupant load factor. Shopping centers with a higher occupant load factor are located centrally in large urban areas.

The purpose of this report is to study the risk of dust explosions at the candy manufacturing plant Leaf Sverige in Gävle, Sweden. The risk analysis was conducted with a preliminary hazard analysis, PHA and event trees. The analysis focuses only on the risk posed to employees and material damages at the plant. No third person injuries have been considered. Another purpose of this report is to study risk awareness and risk communication concerning dust explosions.

By using modern methods of casting concrete, cast in place can get more effective and industrialized. A modern method is self compacting concrete. By using this type of concrete, advantages like improved working environment and rationalized construction can be reached. Because the concrete doesn?t need to be vibrated, the amount of staff on site and the noise can be reduced.

3D, 3D-projektering, IFC, Revit, Navisworks, Cad-Q.

Vid Industriellt UtvecklingsCentrum i Olofström AB utförs bland annat slitageprov av verktygsstål vid plastisk formning av plåt. Parametrar som undersöks är verktygstålsmaterial, plåtkvalitéer, ytbehandlingsmetoder, smörjning och olika kombinationer av dessa faktorer. Den nuvarande testmetoden upplevs av IUC som icke tillräckligt produktionslik. Därför skulle det vara önskvärt med ett mer produktionslikt slitagetest än det nuvarande. Vårt uppdrag var förutom att utforma ett nytt slitagetest även att undersöka intressenters synpunkter på den nuvarande testmetoden och önskemål om ett framtida slitagetest. Inledningsvis inventerades befintliga slitagetestmetoder för att försäkra sig om att särskilja det nya testet från befintliga testmetoder och kartlägga vilka egenskaper som undersöks. Eftersom önskemål om ett mer produktionslikt slitagetestmetod fanns behovet av att göra en studie för att definiera begreppet mer produktionslik.

Arbetet har utförts på ABB i Ludvika med avsikt att förbättra revisionsprocessenför kontroll och skydd. En revision är en ändring på ett godkänt och klarmarkeratobjekt. Då objektet i fråga redan kan vara levererat till kund och man behöver göraen ändring krävs en strukturerad process för att utföra denna ändring. Processen föratt göra detta är i dagsläget komplicerad och kräver en hel del administrativt arbete.Processen använder sig utav ett antal program för lagring och databaser så som,Lotus Notes, HiDraw Studio, och HiDra32.Avdelningen för kontroll och skydd är i fasen att övergå till ett annat elCADsystem, Engineering Base. Detta är också en av anledningarna att man önskar en nyprocess för revisionshantering.Arbetet bestod till en början av inlärning av den dåvarande processen.

The aim of this report is to investigate, on the basis of two consult agencies perspectives, what the possibilities and obstacles are to integrate the work with antagonistic and accident related risks. The report is based on two consult agencies where each agency´s work procedure is represented by a risk management method. The work with accident related and antagonistic risks is analysed and evaluated compared to four different components. The components are risk management process (IEC´s and FEMA´s model), driving forces, education and competence, and resources to control risk management with COSO?´s ERM framework.

Examensarbetets frågeställning berör användarnas medverkan i Requirements Engineering (RE). Under RE-fasen skall samtliga krav på det kommande systemet tas fram från intressenterna. En viktig intressentgrupp i kravutvinningsarbetet är de kommande användarna av systemet. Resultatet av RE-fasen är en viktig faktor som påverkar hela den fortsatta utvecklingsprocessen samt hur lyckat det slutliga systemet blir.Detta examensarbete innebär en undersökning av vad användarrepresentanterna anser om use case-modelleringen i RE-processen. Undersökningen har påvisat att användarrepresentanterna är positiva till use case-modellering som arbetsmetod för att kartlägga kraven.

Failed system development projects are a common sight within the IT-industry. During the last ten years we have seen several more or less disastrous high profile projects being reported in the news. One aspect that might hold some of the responsibility for these failures is the fact that more organisations are knowledge intensive which makes their work processes difficult to capture in computer systems. How requirements engineering is handled becomes even more important in these cases, where processes are unpredictable and rely on individual judgement and knowledge. In this study we have examined the challenges of developing systems for knowledge intensive businesses through a method of qualitative case study of a university laboratory.

This thesis is the result of the investigation and solution of a mechanicalproblem regarding flywheel malfunctions. A flywheel is, in short, a devicethat relies on a rotating object?s moment of inertia to store energy overshort time spans. This project is part of the development of a fourthflywheel prototype at the division for electricity at Uppsala university,which uses magnetic levitation to keep a hollow cylinder rotating at veryhigh speeds inside a vacuum chamber. Should the magnets fail however, orsome other error occur that leads to an uncontrolled state of rotation, thecylinder needs to be stabilized mechanically by a device usually referredto as ?back-up bearing?.

When a disaster occurs the main focus is on the loss of human lives. Here the environmental effects have been in the centre of attention. This work has had two main purposes. The first one was to formulate attributes, variables that together present a complete picture of the consequences that an event has had on the environment. The other main purpose was to investigate how people value the impact that a disaster can have on the environment.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

Syftet med detta examensarbete är att utifrån ett lönsamhetsperspektiv analysera konceptet ModernaHus och hur det ska möta marknadskraven för flerbostadshus på den svenska marknaden..

The computer consultant company Create in Lund AB wishes to facilitate their invoice routines, as it at present is required that the administration finds and compares information from two different systems.The purpose of this thesis is to develop an invoice management system that simplifies the invoice management process for the administration at Create. During the development of the system, I have chosen to follow the software development process Unified Process and also tried to find design patterns that can be applied to the integration.The result of my project is a self-contained application developed using the Java programming language that communicates with the databases of the other two systems and presents relevant information to the user as a set of invoices. Of the 23 design patterns I studied, I used four of them in the invoice management system. However I couldn?t find any connection between any design pattern and the integration of systems.

This report is the final result of the master thesis that have been done at  Sharpman Engineering. Sharpman Engineering is a small development and manufacturing company that produces and make drawings for everything from heavy duty log raft to aids for disabled people. The purpose have been to make one concept that make it easy for elderly and people having problem with knee- and back problem to stand up from a sitting position. The final result will the company have for further investigations and use for a pre-serial production with the goal to produce a new working product.To get an overview of what is on the market have a comprehensive survey has been done, followed by a survey on patent. This patent survey are for no intrusion on existing patents should occur and give new ideas.