This thesis is the result of the investigation and solution of a mechanicalproblem regarding flywheel malfunctions. A flywheel is, in short, a devicethat relies on a rotating object?s moment of inertia to store energy overshort time spans. This project is part of the development of a fourthflywheel prototype at the division for electricity at Uppsala university,which uses magnetic levitation to keep a hollow cylinder rotating at veryhigh speeds inside a vacuum chamber. Should the magnets fail however, orsome other error occur that leads to an uncontrolled state of rotation, thecylinder needs to be stabilized mechanically by a device usually referredto as ?back-up bearing?.

Good comfort for the driver of a construction machine is crucial. Gearshift comfort is an important part of the total comfort. Volvo Construction Equipment Components has a simulation environment of the powertrain, SimPow, which is implemented in Matlab/Simulink. SimPow is mostly used for simulation of control strategies and performance. In order to be able to study gearshifting comfort, Volvo has an interest in developing new models for SimPow.

The aim of this paper is to investigate to what degree the groups in our inquiry work independently. It is a qualitative research, which points to a well?functioning unit, that by definition is not self-governing, but has many traits of self- government. We have reached to the conclusion, that complete self?government does not have to be the best solution, if you want both quality and efficiency.

This thesis is an evaluation of the new traffic solution at ?Skvallertorget?. The innovative theory behind it is to increase traffic-safety by introducing insecurity feelings for road-users. The conclusion of the evaluation is that the newtraffic solution is well adjusted according to guidelines for municipal traffic planning. The evaluation also illustrates the conflict between traffic planners deliberate attempt to avoid clear information and the road users wish to get it.

Nordic Light AB tillverkar armaturer för bland annat butiker och utställningar. För att kunna avgöra vilken armatur som behövs för en viss applikation och för att se hur en viss armatur lyser har kunder efterfrågat fotometriska filer av formatet EULUMDAT. Fotometriska filer innehåller bland annat information om armaturers ljusfördelning. Den utrustning som Nordic Light AB använder i sitt ljuslabb kan mäta belysningsstyrkan i lux på en kvadratisk yta och sedan sparas mätvärden i en textfil med x- och y- koordinater samt belysningsstyrkor. Detta examensarbete har utförts för att ta reda på vad en fotometrisk fil av formatet EULUMDAT innehåller och om det med Nordic Light AB: s befintliga utrustning går att ta fram en sådan fil.

Detta examensarbete är utfört på ITT W&WW i Sundbyberg, Sverige, i samarbete med KTH, Instutitionen för Maskinkonstruktion. Arbetet har gått ut på att finna parametrar som kan användas för att detektera sörpling i en pump. Arbetet har fokuserat på att undersöka om vibrationer och ljud kan ge information om när pumpen sörplar eller ej, samt att utveckla en algoritm baserat på dessa parametrar.När en pump pumpar en blandning av luft och vatten kallar man det att den sörplar. Detta innebär slitage på pumpen samt energiförluster, då verkningsgraden minskar betydligt. Detta är ett problem för bland annat dräneringspumpar inom gruv- och byggindustrin där permanenta installationer och externa sensorer för att undvika sörpling ofta saknas.

This work of examination describes an environmentally oriented product development aimed to develop new packaging with improved environmental and sale aspects of the products from Primus Sweden AB. The report covers the design process from the first collection of facts to the final results with a description of all methods involved in the work. The focus has been on a clear environmental awareness and the report contains a deepening of the concept life cycle assessment (LCA) for product development. In the process, the consumers? opinions of the brand Primus and environmental profiling formed the basis for the packaging to communicate the right values such as quality, technology, environmental awareness and adventurer?s first choice.The deepening of the life cycle analysis shows that composting and other alternative treatment of the biological cycle is not possible to implement in a satisfactory way in the design process.The work results in two final concepts.

Today small metal parts are mass-produced as for example rollers in cylinder bearings. At high velocity cutting the metal is cut with a great force in a scissor-like device. Both precision and repeatability is important to be able to guarantee good quality, but from an economical point of view it is also important to keep a great manufacturing capacity. The part of the process that is most time consuming is when the metal bar, that is about to be cut, is fed to the right position. Therefore it is interesting to examine if the time used for positioning can be reduced.

The purpose of this literature review is to gain knowledge of how a nurse can relieve a patient´s suffering and promote a patient´s health on his/her own without pharmacologic aid. The method is a literature review based on 10 scientific articles. The study is influenced by Antonovskys view of health. The result showed four clear themes: (1) reduced anxiety / worry and physiological effects, (2) well-being and quality of life, (3) steps towards self-care and (4) relations. Relaxation and massage proved to have calming and pain-relieving effects.

Article 4.1(h) in the Rome I regulation establishes which law that will be applicable on contracts concerning financial instruments concluded in multilateral systems. The main problem is that most contracts concluded within these systems have standard clauses which contain a clause on the applicable law. If this is the case, Article 3.1 in the Rome I Regulation is applicable instead. This problem makes it difficult to find a need for article 4.1(h) if it will only be applicable in exceptional cases. However, the legal position on this matter is still unclear since the Rome I Regulation has just been put into force.

Trading based on technical analysis has its roots in the U.S. financial industry where it has long been common practice, in Sweden however the trading style has not had the same impact. Based on the results from the preliminary study we believe this is about to change and that the topic therefore requires further studying. Several online stockbrokers today provide information and tools for technical analysis to their clients. As the list of indicators to use for creating strategies is so immense it is interesting for an investor to know what actually could be the basis for a profitable investment strategy.

This thesis work has been performed at the department of diagnosis and dependability at Volvo Car Company, Torslanda. The background of this project is based on interest in ascertaining how different factors possibly can affect a diagnosis method, which has been developed to find leaks in the fuel tank and evaporation system. According to the OBD II requirements leaks with an orifice diameter larger or equal to 0,5 mm, must be detected. The idea of the diagnosis method is to create an over pressure in the system with an air-pump. The current through the pump is measured and correlates to the power consumed by the pump.

This is a thesis presents a differential gear which is found in a tracked vehicle called BvS10. The tracked vehicle is manufactured by BAE Systems Hägglunds AB in Örnsköldsvik, Sweden. The differential gear has a bolted house. The differential meets the requirement specifications, but the problem is that the bolts are sheared off because of the extreme torque that the differential is exposed to resist.Previous report on the differential show pictures of bolts which have been sheared off at the threads. This report is also includes three lists that explain seven different proposals which some are approved and some are not, and the report also presents the force, tensile, and shear stress.In a bolted connection there is both axial tension stress and radial shear stress, which can lead to wear out and broken bolts.

Due to an increased population in cities the need of densification of cities increases. This means that the amount of ecological elements in the city is at risk of decreasing. Ecological services contribute to the city?s climate by softening the negative impacts that densification of cities means. Thus increases the will and ambition in city planning in to preserve greenery.This is an interdisciplinary thesis within the subject of geography that studies Biotope Area Factor (BAF), a planning tool that is used in city planning with the purpose of compensating for lost ecological services associated with new housing estate.

In the increasing urban environments and the modern societies demands for sustainability there is a challange in planning cities with a balance between density and a satisfying access of recreational environments. For attractive cities these environments need to be designed to fit every inhabitants? demands and opinions in some way. Increased knowledge and understanding is therefore needed about how different design styles in landscape architecture affect people and the cities. In this bachelor thesis benefits and disadvantages as well as the experience and impact of two fundamental design styles i discussed; naturalistic and formal/abstract design.