As the final course in the education ?University Diploma Programme for Process Operators? there is a thesis in cooperation with a company required.This thesis is about operator maintenance and 5S made at Metsä Board in Husum.In this report you can read my opinions and conclusions based on literature studies and the interviews that have been made with the staff at PM6 (the paper machine).I chose to focus on the theory of lean, 5S and operator maintenance because it covers the area of this thesis.The operators shall do their rounds to make sure that the equipment works fine. They shall also write down things that they notice in a checklist. This is not done as it should be and the question is: can this be solved by using 5S?My conclusion of this thesis are:Better review of the task so that everyone is involved.

The global climate-change means increasing mean-temperature and higher precipitation in Sweden, which leads to shorter periods of frozen ground in the forest. At the same time the harvesting machines are getting bigger and more powerful. The forest industry aim at an even wood flow, and the ground damage has to be as low as possible. The two biggest causes for ground-damage is the bearing capacity of the forest ground and the ground-pressure of the harvesting machines. The aim of this study was to find out some rules for the machine choice considering ground pressure, when harvesting on ground with low bearing capacity.A field study, using a Valmet 890.3 forwarder, was carried out where different ground pressures and their effect on the ground were tested on two different types of ground.Additionally, an inventory of damaged harvesting grounds was made.

This report presents a thesis project conducted by two students at Mälardalens högskola. The project covers 15 points in industrial design and was conducted during April to June 2014. The principal of the thesis works at Plastic Produkter. The assignment was to develop equipment for an effective way to dose, mix silicon, fill a special designed plastic bag and then seal it. The bag is then formed into a breast model.When a customer for various reasons decides to do a breast augmentation or a breast reconstruction, there may be doubt or uncertainty about the result.

AbstractThis bachelor thesis has been assigned by the company ACG Nyström, Borås. ACG Nyström is working in cooperation with a Swiss company named Jentschmann AG. Jentschmann is a manufacturer of ultra sonic welding machines which ACG Nyström is marketing in Scandinavia and the Baltic States. On behalf of Jentschmann AG the company has the aim to introduce the ultra sonic welding technique to new companies.The aim of this thesis is to compare traditional sewing machines with ultra sonic welding machines within two textile areas, protective clothing and outdoor living.Two investigative questions have been formulated for this purpose: what are the differences between a sewing machine and an ultra sonic welding machine? Is it possible to replace the sewing technology with ultra sonic welding? These stand as guidance for this paper.To gather knowledge interviews, literature studies, and tests on two different ultra sonic welding machines were performed.

Buffer zones play an important role for the water quality in our watercourses. When harvesting a forest close to a watercourse a buffer zone should be left. When it's not left, it will lead to radical changes in the environment for the water organisms. The overall purpose of this thesis was to illuminate the production- and environmental thinking when establishing new buffer zones in south of Värmland. The partials goals were to determine choice of tree species, ways of regenerate, occurrence of soil scarification and the occurrence of machine tracks in newly established buffer zones.

This report examines the industrialization of a newly developed household machine on behalf of Technogarden Engineering Resources in Karlstad, Sweden. The report is a part of the final course in the Bachelor Program in Mechanical Engineering at Karlstad University and takes place in spring 2014.An innovator, an investor and a engineering consultant firm have through collaboration developed a new type of gruel machine. The product is in its final stage of construction and is planned to be manufactured in a production located in Sweden, autumn of 2014.To compete against today?s trend in outsourcing manufacturing to low cost countries for better profitability, the industrialization of the gruel machine must be done with a minimum amount of resources in order to become successful, which also describes the problem of this study. Using pre-study material in form of Lean production literature, visiting a successful production site and gathering data from involved engineers a specification was developed which describes what this industrialization must achieve and which requests can be accomplished.

GPS (Global Positioning system) and GIS (Geographical information system) has been used for planning and inventory in the forest sector for more than ten years. The last years the development has come to equip harvesters and forwarders with GPS and GIS (GIT). The goal with this study was to reach a basis for decision, how Stora Enso Skog should continue its investment in GPS and GIS in harvesters and forwarders. To reach this basis for decision, possible advantages and benefits, disadvantages and problems in the harvesting process was evaluated. The study was made as an interview study with four harvesting managers and ten machine teams. To secure the quality of the results an interview questionnaire was made before the interviews were done. The results showed that GIT will make the harvesting managers work easier.

This essay serves to illustrate the main practical differences between the popular medium-level programming language C++ (C Plus Plus), and the newer high-level language C# (C Sharp). It will focus on the aspects that are readily apparent to the application programmer, such as differing syntax, constraints and capabilities.It will also feature a similar comparison between the open source OpenGL graphics library, and the proprietary Direct3D graphics library owned by Microsoft Corporation.It will not go into the differences in ?under the hood? mechanics that the application programmer seldom have to consider after having chosen his programming language or graphics API, such as C# being compiled into an intermediate language and is run on a virtual machine where C++ is compiled directly to machine code, or the differing principles of rendering in OpenGL and Direct3D.This is by no means comprehensive, many things have been left out or overlooked..

This report presents a thesis project conducted by two students at Mälardalens högskola. The project covers 15 points in industrial design and was conducted during April to June 2014. The principal of the thesis works at Plastic Produkter. The assignment was to develop equipment for an effective way to dose, mix silicon, fill a special designed plastic bag and then seal it. The bag is then formed into a breast model.When a customer for various reasons decides to do a breast augmentation or a breast reconstruction, there may be doubt or uncertainty about the result.

Netadmin Systems är ett Linköpingsbaserat IT-företag där huvudprodukten NETadmin är ett Operation support system/Business support system (OSS/BSS) som i huvudsak används i öppna nät för bl.a. kund- och lagerhantering, provisionering, övervakning och ärendehantering. Ett växande behov finns att göra det möjligt att använda övervakningssystemet via mobila enheter för att kunna felsöka och hantera driftstörningar effektivt.Syftet med rapporten är att undersöka hur övervakningssystemet kan göras tillgängligt på Android samt att ta fram en prototypapplikation för hantering av grundläggande övervakning. Genom fallstudien som har genomförts har slutsatsen dragits att Netadmin API är lämpligt för kommunikation via mobila enheter men att API behöver vidareutvecklas med ytterligarefunktioner. De viktigaste av dessa har implementerats och arbetet har även mynnat ut i en applikationsprototyp för Android.Genom utvecklingen av denna applikation ges Netadmins kunder möjlighet att hantera övervakningssystemet via mobila enheter..

The saw blade producer, Håkansson Sågblad AB, patented in the U.S. a new blade profiledesigned specially to cut fish and meat. The most important advantage of that blade is that its teethare not set, therefore the material lost when cutting is really smaller. The special geometry of thatprofile made that nobody had found a proper way to produce it before.The goal of the outlined work is to develop a machine to produce these new blades in afeasible way.The research approach of the project can roughly be divided into three phases:1.- Invention and development of a proper distribution of blades to produce a big amount ofthem at the same time.2.- Research of the best production process to produce the blades.3.- Main design of the machine to produce the blades.In the Thesis these three points are carefully developed and studied in the form of the startpoint of a really bigger project. Some tests had been done in order to prove all the analytical ideasand the results obtained had been satisfactory enough to give Håkansson the start point of a bigbusiness.

In the current situation is the straight tube cutter, that provides Luvata?s line of large recoolers with copper tubes, manually operated. To prevent damages and facilitate mounting the tubes must be properly arranged when they leave the machine. This report aims to investigate and present an automated solution where the operator does not need to participate in the process. A number of theories have been drawn up and tests have been done.

This report was written as a result of a Bachelor Degree Project at the School of Technology and Society at University of Skövde spring 2007, together with Jede AB in Mariestad. The report covers the development of a door to a coffee vending machine that is under construction, and will in a chronological order describe the project from ideas to final product.The project started with a rather extensive feasibility study that thru market research and user tests sorted out the opinions of potential customers, concerning today?s available assortment. Technical areas concerning materials and manufacturing methods were also scrutinized for the consideration of the possibilities of a future production.The next step was to constructively generate ideas and thoughts that later on could grow to be potential solutions. After several weeks of hard work and pieces of good advice and recommendations from the assigner, four comprehensive concepts were built up.

A vehicle that carries a person sitting in a wheelchair has been rebuilt. The original vehicle was provided with a petrol engine, hydrostatic drive and a mechanical steering rod, making it noisy and hard to maneuver. The purpose with this project was to convert the vehicle to make it more environmental and easier to drive.A new design has been proposed where an electrical drive has replaced the noisy combustion engine and an electrical motor with joystick control has replaced the manual steering.The project was divided into two parts. One mechanical part where the construction of the drive and steering were to be decided. The other part involved programming the microprocessor and implementation of all the necessary electrical for the control system of the vehicle.

At the Division of Electricity at Uppsala University there is an experimental rig forhydroelectric generators. The experimental rig?s vital part is a 12-pole synchronousmachine, whose electrical characterizing parameters (resistances, inductances andtime constants) are unknown. The aim of this thesis is to characterize the machine inits current state by perform a Standstill Frequency Response (SSFR) test. From theanalysis of the measurement data, which is a part of the test, a set of basic parametershave been received.