The purpose of this work was to see if it was possible to rebuild an old dairy house into a house fore sheep production. The goals fore the work was to see witch kind of production model was suitable, how the actual drawing would look like and witch kind of interior was needed. The building was built in the beginning of 1900. It is located on the mountain Kinnekulle in Sweden. It was a big production fore its time and hade about 60 dairy cows. It was a lot of hard work because the floor was built by big stone blocks and it was very hard to rebuild when some more automatic solutions came fore handling all the manure. The idea of remaking the building came when we rebuilt the roof fore 5 years ago.

Material handling is a term that includes all kinds of handling of material from a raw product to a finished one. ABB is active in the following segments; foundry, packaging and palletizing, metal industry and plastics industry.The demands for efficiency and reliability have been set very high in the industrial sector. Optimizing of the material handling will give the company higher cost-effectiveness. Around the robot there are different kinds of material flows, to optimize the cycle time, consisting of carriages combined in different ways.Motion Control is a complex system with main functions such as; positioning, synchronizing, indexing and more. The products in the system need to cooperate to make these functions possible therefore integration of motor- and servo products are important.

The aim of this project has been to raise the production efficiency of Daliff Precision Engineering through reduced transportation time and a more standardized manufacturing process. The problem has upraised because of a big and diversified product flora without any standard products and with just small batches ordered. The report also tries to show the work procedure with general analytical methods and be an example of how a similar problem can be resolved. The transportation time is being proposed to be reduced through a change in the layout of the factory. By moving a few manual machines, dispatch and burring to more efficient locations, the total transportation time will be reduced by 55 %.

Considering that the current technology is constantly improving, it becomes increasingly important to have an efficient logistics in a company to maintain profitability while achieving a competitive business. Efficient logistics may be accomplished by improving the internal materials handling. In this thesis the internal material handling of steel frames has been studied at a factory in Vaggeryd. The goal of this study is to investigate the problems that exist with the current production flow of products and provide suggestions on how it can be developed to reduce unnecessary handling and movement.The study has a deductive approach where the authors has been using literature studies parallel with empirical analyzes conducted at a company to achieve the purpose of the study. Documentation from the company and interviews with staff and observations form the basis for the data collection carried out.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The company System Andersson is developing systems for controlling materials and production in industries. They want to add a new service, where parts of those systems are accessible through cell phones.In this paper we are investigating which technology are best suited for this kind of application. And then we describe how we are developing a prototype fort this application, based upon that technology. After investigating technologies such as Java ME, Microsoft Silverlight, and web applications we settled upon building the system as a web application, customized for a mobile environment.To build a web page which is readable by many different cell phones we use the markup-languages which are developed for cell phones. We put much effort in reading about the standards and recommendations for the mobile web, produced by the organizations W3C and OMA.

This Master?s Thesis aims to investigate and assess the methods used to decrease the discharge ofmetals, primarily copper, from the water purification plant at Assa Industries plating factory inEskilstuna.Literature studies of the purification methods precipitation, ion exchange, evaporation, reverseosmosis and electrolysis has been done to appraise the adequacy of the technique. Thesetechniques are commonly used for purification of industrial waste water.Assa has four plating lines: the Trumline, the big Zinkline, the new Zinkline and the Decorativeline. The new Zinkline is the most modern of the four lines and purification is done byrecirculation over an ion exchange unit. The demand for fresh water is thereby heavily reduced.The Trumline, the big Zinkline and the Decorative line all use older techniques.

BillerudKorsnäs is a leading global provider of primary fiber-based packaging materials and on Gruvöns Bruk in Grums, they have chosen to invest millions in the boiler at the facility to increase the total capacity of the factory. This results in the Pulp Flash Dryer at Gruvön being burden more, which makes it important that it is of great reliability and can be run with a high capacity. The reliability of the Pulp Flash Dryer at Gruvön is not as good as one could hope, which leads to reduced availability and production, as well as to increased maintenance costs. There are a number of different reasons for this, but all the casual links are not known.The purpose of this project was to perform a system analysis of the Pulp Flash Dryer to identify bottlenecks and the most critical parts from a capacity- and availability perspective. Appropriate methodology for the system analysis was used and would be used in a structured way to perform the analysis with data from the process and the maintenance system.

This master?s thesis was performed during the fall of 2006 at Cloetta Fazer AB in Ljungsbro. Cloetta Fazer is the market leader in Scandinavia of manufacturing confectionary and chocolates. The purpose of the project has been to identify causes that impact the quantity of waste in production as well as a cost/benefit analysis of the solutions that can reduce the problem of production waste.The work includes four production lines that are individually designed depending on what kind of product that are produced on the line. By using qualitative and quantitative methods such as focus groups, interviews and observations data has been collected.

This thesis is about developing a design that provides improved vacuum seal between a lead coating and a plastic coating during plastic extrusion processes of cables. This report is a part of the course MSGC 17 for Bachelor Engineers in mechanical engineering.The work is performed at Nexans Norway AS in Halden where they have a production of high voltage cables for sea-, and offshore industry. A problem they face is that they do not get enough good seal at the attachment to the plastic extrusion machine. They want to achieve a vacuum between a lead coating on the cable and a plastic coating of the cable for plastic extrusion, which is something they do not achieve today. The thesis is thus to come up with a design that provides better sealing against the cable.The work involves a construction part with the phases of product development processes.

This report was written as a result of a Bachelor Degree Project at the School of Technology and Society at University of Skövde, first semester 2007. The assigner was Tibrokök in Tibro, Sweden. The commission was originally to design a sliding door concept for kitchen. Later it was expanded to also include bathrooms.During the feasibility study of the project Internet was used as an information source. Kitchen brochures and magazines were ordered from different companies to give inspiration and ideas.

The situation at Plastal AB is following; the plant in Simrishamn has not capacity enough but the plant in Kristinehamn has unused capacity. My task with this master thesis is to build a logistic flow between this two plants, optimize purchase quantities and ensure delivery safety.The production of the Intermediate Section (LS) will be divided between the plants. The LS will be produced in the following way; the injection moulding process will be done in Simrishamn and the assembling and lacquering processes in Kristinehamn, The reason to divide the production is to ensure delivery safety. Plastal AB can not move the whole production of the l.S because the two plants have different processes (moulding res. injection moulding).When the 1.5 has been transported to Kristinehamn following moments are included in this order; lacquering, welding and assembling.

There is an uncertainty in the market for grain forcing the meat/milk producers to review alternative feeds to a larger extent, in order to get control over the feed costs. This has led to that the meat/milk producers need to have a good knowledge regarding how the different feeds influences the animals and which technical equipment to use for handling. For those that produce their own feedmix, there is a need to put interest in new crops and their characteristics to be able to get the knowledge of what is required for their own production. It is beneficial to keep an open dialogue with advisors to be updated in new crops and new technology for feeding. When mixing feed at farm level, the legislation is not very clear since it the target group is large scale mixing plants. We have brought up the most important rules and regulations from the EU parliament Council as well as the ones from the Swedish Board of Agriculture (SJV), regarding feed mixing on farm and factory level. We have studied beans and pea at two different moisture levels, in order to evaluate how the moisture level affects the distribution of particles when milling with a plaitmill and a hammermill.

Saab Training Systems (STS) in Huskvarna is manufacturing material for educationalpurposes to armies worldwide. They are now implementing parts of the Lean productionconcept in their organisation.One part of the work with Lean production is to eliminate waste. To be able to identify waste,value stream mapping is a good tool and also what we used in our thesis. To gain a betterefficiency in the production of Personnel Detector Device (PDD) flow was one of our goals.The PDD is a harness used during battle training which registers if the user is being hit by itsenemy.Our work with the thesis started up with a short education in Lean production and in valuestream mapping (VSM). The work proceeded with a VSM of the production flow of the PDD,interviews were made and studies of literature were done to gain greater knowledge of thesubject and solve the task.The VSM resulted in five areas which were followed up out of those six we identified.

Listeriosis, which is caused by Listeria monocytogenes, is a rare food borne disease that primarily affects people whose immune system is weakened. These may be elderly people, pregnant women, new-born infants and individuals on immunosuppressive medication. The most common symptoms are meningitis, septikemia and abortion. The mortality is high, on average 20-30 %. In recent years the number of cases in Sweden has increased.