As a consequence of increasing wind power installations in the Nordic grid the last years, the need for regulating power has become larger. In the Nordic grid, regulating power is mainly provided by hydro power. One part of the regulating power is called frequency control, which ensures that the grid frequency is stable and close to 50 Hz.However, setting the turbine into frequency controlled operation may cause stress and wear of the components in the mechanical control system. Frequency controlling implies large and frequent servo forces and longer travelling distance of the sliding bearings in the Kaplan turbine.Based on one selected Kaplan turbine, Selsfors G1, measurements and MATLAB calculations have been performed in order to determine forces and movements of the linkage system. With these forces and movements as input, stresses and fatigue have been determined as well as sliding distances, bearing pressures and wear of bearings during a typical lifetime of 40 years.The results indicate that no severe wear exists on the bearings during 40 years of service.

The aim of this study is to evaluate whether the value of occupant load is over or under estimated when the Swedish general value for department stores, 0,5 person/m2, is used for dimensioning shopping centers. The data that was analyzed derives from seven shopping centers and one department store. A conservative method was used to calculate the occupant load factor. The analysis shows that two groups can be discerned: one group that is characterized by a lower occupant load factor that does not exceed 0,3 person/m2, and one group with a higher occupant load factor. Shopping centers with a higher occupant load factor are located centrally in large urban areas.

At the beginning of 2011, Sweden started using the European rules for structural design, the Eurocodes, instead of the previous national rules. In both the previous rules and the Eurocodes, it is possible to dimension concrete columns using tabled values. However, the required cross section measurements have increased considerably. Moreover, it is possible to dimension concrete columns using calculations, however, this is unusual.The development of a fire in a fire cell can be divided into the growth stage, the fully developed fire and the cooling phase. The duration of each phase, as well as the temperature, is dependent on a number of factors, e.g.

The purpose of this thesis is to investigate the degree of influence of holes in the web of steel beams with long spanson weakening of their bearing capacity. Making holes in the web of the beam generally reduces the bearing capacity of the beam. However, it might be necessary seen from both an architectural perspective as well as from a building services perspective by creating an opportunity for building installations.The objective of this thesis is to examine how much an I-beam can be weakened without sacrificing safety and functionality. The investigation has been done by using Finite Element Method through commercial software.The regulation for structural design of building structures in Sweden used to be specified in the document known as BKR. But this was replaced by the European norm Eurocode back in May 2011.

Syftet med denna undersökning har varit att underlätta för företaget Re-Load att presentera sin lastpall som produkt för potentiella kunder. Syftet har också varit att stötta Re-Load till att bli licenserad EUR-pall samt att successivt ersätta befintliga lastpallar och långsiktigt exekvera företagets affärsplan. Målet har varit att undersöka produkten avseende lönsamhet, miljöinverkan och hur den påverkade arbetsmiljön. Under-sökningen har genomförts med ett befintligt flöde där produkten använts och utifrån detta kunde en flödesstudie samt en komparativ produktstudie utföras med en alternativ lastpall. Med data hämtat ur detta flöde utfördes en investeringskalkylering, miljöberäkningar, subjektiva intervjuer samt dokumentation.

In Sweden today, the consumers have the opportunity to use the different sales channels; physical store, online store and brick and click, a combination of both. For the past decade, the use of ecommerce has spread tremendously and the fashion industry is one of the top three industries in this category. This, together with the growth of technology, have created new opportunities for consumers during their online shopping. The purpose of this study is to examine the differences between consumers who use physical store, online store or both. This study aims to look into consumers' shopping habits within these sales channels and factors that are affecting them.

This paper briefly summarizes Bergslagen as a bedrock province in order to give background to the genesis and presence of REE-bearing minerals (short for Rare Earth Elements) in the region. These mineralizations mainly occur along the REE-line, a line aproximately a hundred kilometers in length between Norberg in the north and Nora in the south with a width of a few kilometers. Situated in the southwest of Bergslagen it is currently one of only a few places in Sweden where REE-bearing iron oxide mineralizations are potentially economically viable for mining. Ore microscopy has been conducted in order to characterize an ore sample from Myrbacksfältet, one of few sulphide rich iron oxide mineralizations within the REE-line. Additionally, an electron microscope analysis of a sample from Stålklockan, a suspected REE-bearing mineralization also within the REE-line was confirmed by EDS (short for Energy Dispersive Spectrum) analysis.

The aim of this study was to develop a load prognosis model for Uppsala district heating system to be used as a tool for heat production optimization. The methodwas to build three models for the different customer types; housing, industry andoffices and then scale them for the total system using data from Uppsala districtheating system. The heat load consists of two parts, one that is temperaturedependent and one that is dependent of the social behavior of the customers. Thetemperature part was modelled with an ARX model using an outdoor temperatureprognosis as input signal. The social behavior part was modelled using the mean ofthe social behavior from some days before and additionally by distinguishing betweenweekdays and weekends.

A pavement construction designed to cope with the different type of traffic loads; it is exposed to and at the same time it can resist the effect of the climate. A road structure consists of sub- and superstructure which is divided by a boundary known as terrace. During the construction of unbound layers (base course and sub-base course) in the superstructure, it is always ensured that the material meet the requirements for bearing capacity and the degree of compaction. These parameters are controlled by various laboratory tests and control methods. To obtain increased knowledge of the material and improve the quality of the compaction in the field, it is necessary to perform laboratory tests in order to determine material properties.A base course material 0/ 32 mm limestone from Gotland (Hejdeby) was investigated in this study.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The work thesis was performed at Assalub a company which is situated in Åtvidaberg. The company works with developing, manufacturing and marketing equipment for handling of lubricants for light and heavier industry. The work thesis it is based on a inquiry Assalub got from MacGregor which is a company within cargo solution, from port to offshore system.For unloading grain and other material from the ship cargo it is used combined inlet feeder and screw conveyor, there the inlet feeder is drilling down through the cargo and feed the screw conveyer with material to further destination. At the bottom of the screw conveyer and the inlet feeder there is a bearing that keep the parts together. However the lubrication of the bearing must be made manually.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

There are many old dams in Sweden and, since few dams are constructed today, the main task in risk assessment on the existing dams is often to reduce the risk of failure. RIDAS (Swedish Guidelines on Dam Safety) is used when designing new dams and assess the existing ones. The guidelines include stability requirements for different failure modes, e.g. overturning and sliding, which imply that the load effect from e.g. uplift and ice load need to be less than the resisting loads or moments.

The climate changes that are occuring in the world have resulted in that the EU callingfor a 20 % reduction in energy consumption to the year 2020, to reach that goal theEU want the public sector to go forth as a good example. Västfastigheter owns andmanage the hospital buildings in the Västra Götaland region. To be able to reducetheir energy usage Västfastigheter has hired several consulting firms to chart out theenergy consumption on each hospital building. The biggest energy savings potentialhave been calculated and what the cost will be to perform each action. The energyaudit have been completed and stand as the decision basis for Västfastigheter?s choiceon which action packages that should be implemented.