The power consumption has grown rapidlyin the last decade. Fossil fuels and theneed for alternative energy sources aregreat. Ocean waves are a renewable andsustainable source of energy that hasbeen relatively untapped. At UppsalaUniversity research and development havebeen done for several years. Severaltypes of wave energy converters (WEC)have been created.

Friend lists allow Facebook users to group their friends and may be used to share certain information only with those in a specific list. This function has been around for several years, but has never gained any particular popularity among users, most of whom probably did not know it even existed a couple of years ago. In the fall of 2011, however, the function was updated and made more visible on the site.There are several possible uses of friend lists, such as privacy control, filtering of the news feed, self-presentation and targeted information sharing. This paper aims to investigate the extent to which friend lists are used by students today, as well as why students actually use their lists, i.e. for what purposes.Judging from the results of this study in comparison with earlier research, there seems to have been a somewhat recent increase in the awareness of the fact that friend lists actually do exist, but still most users tend not to utilize them.

A method for measuring the total impulse from a multi hole diesel injector, introduced inprevious thesis work, ?Development of a method and a device for measuring the momentumrate of fuel sprays?, by Mikael Lindström, has been further developed and tested. The conceptis to simultaneously deflect all sprays from a multi hole diesel injector by using a bell shapeddeflector. The fuel sprays are deflected straight down from their initial umbrella angle, andthe resulting deflection force is measured in a thin strained section of the load cell. The strainis given by three strain gauges, with quarter-bridge circuitry for each gauge.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

This Master?s Thesis aims to illustrate in what ways the two Swedish environmental assessment tools, the Environmental Load Profile and EcoEffect differ and if performed valuations gives different results and environmental goals.The built urban environment causes about half the environmental loading in Sweden. The society?s ambition towards sustainable development has resulted in demands reducing the environmental load. One way to accomplish this change is with the assistance of tools for environmental assessment of the built environment.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

Combustion of fossil fuels is today the dominating source of energy. During combustion,carbon dioxide is formed. The carbon dioxide accumulates in the atmosphere,which raises the global average temperature on earth through the so called greenhouseeffect. The only way to reduce the emissions of carbon dioxide from combustionin a coal fired power plant is through carbon capture and storage (CCS).Post-combustion capture is a technology to separate carbon dioxide from the uegas after the combustion for efficient transport and storage. The steady state operationof coal fired power plants with post combustion capture has already beenthoroughly investigated on a pilot scale, however much work remains to investigatethe plants dynamic operation.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

Tomo Hugglink (TOMO Skog) is an innovation for harvest and transport of biofuels. The system consists of a truck, a chipping unit and crane mounted on a link and a wood chip trailer. The system works in such a way that the chipping unit is disconnected and placed on the site and wood chips are loaded directly into the wood chip trailer.The aim of this study was:- To examine the performance of the TOMO Hugglink system under different conditions such as the size, placement and quality of the pile.- To calculate the cost per raw ton for two vehicle combinations at different transport distances and to examine the effect of a reduction in set-up time and an increase in load weight.- To identify possible improvements with the TOMO Hugglink system.A time study was conducted within the thesis work to make it possible to determine production and time consumption. In the subsequent economic analysis the cost per tone at different transport distances was calculated for two different lorry concepts. Furthermore the effect of a reduction in set-up time and an increase in load weight was calculated.Under current conditions the utilization of the chipper is low and only 29 % of the total system time is occupied by chipping.

The Island of Öland has one of the best wind climates for land based wind power in Sweden. An objective for the Island is to become self sufficient using electricity from renewable source of energy such as wind. There is currently 55 MW capacity installed on the Island and it is estimated that grid congestion will occasionally occur if more than 135 MW was installed.The aim of this thesis is to investigate he possibilities for load management by smart charging of electric vehicles, EV. The definition of smart charging is that the charging is done to some extent with an ICT-system, (information and communication technology) that correlates wind electricity generation to the charging of electric vehicles. The purpose is to avoid grid congestions on the sub-sea cable that connects Öland to the mainland because that in turn would curtail wind energy production.

Photography has long been of importance for humans in aspects of community, sharing and documenting. It has previously only existed in analogue format and with larger cameras. We have presently reached a new generation of cameras and photography. The new smaller compact cameras that are provided with most cellular phones take digital images of varying quality and accounts for a large part of photography. With the emergence of social media, photography and social interaction combined came photo applications with different features.

In offshore oil production FMC Subsea systems use a product called cap. The cap´s mainly task is to protect hubface and seal areas on inboard hub against dirt, corrosion and mechanical damage under installation of a subsea system. A new model of a cap has been designed and analysed using finite element method. The model is called KC3-12 and has a new function, emergency release, which is a backup method for the ROV (remote operated vehicle) to release the cap from the hubface when it is placed under water. The cap KC3-12 was found to fulfil the criteria under the test load pressure, according to ASME VIII, div2.

This thesis aims to contribute to improved functional procurement of photovoltaic systems, PV systems. Functional procurement means that criteria concerning a function are set rather than specifying technical details or products. Possible advantages and difficulties in using functional procurement have been analyzed by interviews, simulations and a case study. Electricity production and surplus production for different scenarios have been simulated via MATLAB. The MATLAB script was also used to generate rules of thumb on feasible solar fraction for six different load profiles; a church, a farm, a car mechanic, an office, an industry and an apartment building.

This master thesis covers the development of an automatic tuning process for the existing speed controller for drive systems. The drive systems are resonant two-mass systems where a motor is used to drive a load connected by a shaft. The developed method relies heavily on system identification and the construction of a complete mechanical model of the process. With this approach, the common problem with poor load speed control that derives from measuring only the motor speed can be addressed and solved for a majority of such processes.The automatic tuning method has along with general test functions been implemented in a complete tool for automatic tuning, testing and performance evaluation and reporting for drive systems..

To be able to move around without having to think about each movement is for most people amatter of course. Todays society contributes to a life at high speed where the sparetime is oftenspend doing somekind of sport, even extreme sports which earlier only a few people wheredoing. This leads to not only good health effects but also to more injuries. One of the mostcommon injuries is the knee injury.Capio Artro Clinic is a clinic specialized in sports medicine and particulary patients with injuriesin knee, shoulder, foot, hip or elbow. They perform a great part of all the crucial ligamentsurgeries in Sweden and has therefor also a lot of patients in need for rehabilitation of the knee.During the rehabilitation the load of the injuried knee is increased in steps.