This thesis has been performed at Scania CV AB Technical Centre in Södertälje and its aim hasbeen to study the causes and effects of deformations in the interface between the rear axlehousing ADA1100 and the central gear house R780 during operation. Design changes that wouldincrease the sealing capability of the studied interface are also suggested. Finite element (FE)and CAD software have been the primary tools in this study.Finite element (FE) simulations are used in the industry to predict and develop engineeringdesigns. The main motive for FE simulations has traditionally been to identify weak spots in thedesign, regarding high tensions and large deformations.The FE model is an aggregation of submodels and interface models that represents the rear axlehousing, suspension, central gear, central gear housing, wheels, bolts and weldings, and theirinteractions. The submodels have different material properties and they are connected withcontact interface models.Boundary conditions are defined on the bushings in front of the rear axle and on the air bellowsbehind the rear axle.

The voltage level in the power grid varies due to variations in load and production. Normally these variations are manageable, but they may be excessively large during a disturbance. If the voltage is too high it may damage the equipment in the grid and too low voltages may cause problems like voltage instability. The magnitude of the voltage variation depends on the short circuit power capacity of the point of interest.This problem may become lore prominent due to automatic voltage regulation that acts on shunt reactors and shunt capacitors. When the shunt reactor is connected or disconnected to the grid it may cause such large changes in the voltage that the shunt reactor starts hunting.

The thesis presented in this report has been made on behalf of Scania and their basic frame design department with the subject to solve an implementation of a weight sensing system in the chassis. The system is supposed to be implemented in the seat springs, and the reason for this is that all the force will have to go through the weight sensing transducers. With all the force going through the transducers the weight sensing system will not be sensitive for the differences in tolerances from manufacturing. The transducers could be pre-calibrated to avoid a calibration of the whole vehicle after it?s completed from the manufacturing line.Weight sensing systems is today a reality in trucks with air springs.

Safe operation of a large synchronous power system as Nordel is not an easy task.There are several aspects to take into consideration. This thesis focuses on the problems due to voltage collapses in a transmission system.The ability to foresee an upcoming collapse is vital to maintain stable operation of the grid. The grid operator at Svenska Kraftnät (SvK) uses the computer program SPICA to predict the maximum transfer limit at specified transfer sections. SPICA uses actual states from the grid to predict the transfer limitation, and a quarter later a renewed estimate is produced and so on. This means that the operator can se his transfer limits vary every fifteen minutes.Our task in this project is to validate the accuracy of the limitations obtained by SPICA.

Transmission of reactive power is well known to cause active power losses. Thus, newcomponents who can help minimizing these expensive reactive power flows are ofgreat interest to the power distribution companies. ABB Corporate Research hasdeveloped the first electronic power breaker. One possible application for thisbreaker is transient-free switching of capacitor banks. This could prove a usefuldistribution voltage complement to the switch-sync technique, mainly applied to transmissionvoltage level.

Alkali-kiselsyrareaktionen (AKR) är en kemisk reaktion som medför att spänningar uppstår i betongen då den bildade silikatgelen expanderar. Reaktionen kräver tillräcklig hög alkalihalt, reaktiv ballast samt vatten. På grund av de AKR-inducerade spänningarna är det av intresse att få kunskap i hur reaktionen påverkar betongens böjmomentkapacitet, förankring samt skjuvnings- och genomstansningskapacitet. För att besvara frågeställningen har därför en omfattande litteraturinventering tillsammans med tre kompletterande intervjuer utförts. Resultat som har erhållits, påvisar att två huvudsakliga effekter fås av AKR.

This report aims to examine the design of a passive house. The design addresses the selection ofmaterial, sizing and selection of both building services systems and building technical features suchas load-bearing framework and moisture control. Interior layout is designed for a family of twoadults and one child.A big part of the report is devoted to an in-depth comparison of three different wall constructions ofpassive house standard. The structures that have been compared are a lightweight timber structure, aheavier concrete structure and a sandwich wall of the brand Weber Leca. The report covers variousaspects such as air flow, wall thickness, the risks associated with the construction, U-value, thermalbridges, power consumption, price, and assembly costs.

Three-dimensional computer graphics enjoys a wide range of applications of which games and movies are only few examples. By incorporating three-dimensional computer graphics in to a simulator the simulator is able to provide the operator with visual feedback during a simulation. Simulators come in many different flavors where flight and radar simulators are two types in which three-dimensional rendering of large terrains constitutes a central component.Ericsson Microwave Systems (EMW) in Skövde is searching for an algorithm that (a) can handle terrain data that is larger than physical memory and (b) has an adjustable error metric that can be used to reduce terrain detail level if an increase in load on other critical parts of the system is observed. The aim of this paper is to identify and evaluate existing algorithms for terrain rendering in order to find those that meet EMW: s requirements. The objectives are to (i) perform a literature survey over existing algorithms, (ii) implement these algorithms and (iii) develop a test environment in which these algorithms can be evaluated form a performance perspective.The literature survey revealed that the algorithm developed by Lindstrom and Pascucci (2001) is the only algorithm of those examined that succeeded to fulfill the requirements without modifications or extra software.

Due to recent legal enactments regarding carbon dioxide emissions, the car industry is facing higher demands. An effective way of reducing these emissions is to minimize the weight of the vehicle. This thesis constitutes a feasibility study on whether or not it is applicable for the car industry to utilize an inner floor structure comprising composite materials. The principal was the projectSåNätt, in which the main participant was Volvo Cars Corp. In consultation with a reference group, consisting of delegates from the industry and KTH, a specification of requirements was produced.

Title: What drives the customer's choice of packaging and which factors influence the customer's packaging cost? ? in the automotive and manufacturing industriesAuthor: Lena AnderssonSupervisors: Annika Olsson, Division of Packaging Logistics, Lund Institute of TechnologyHelena Claesson, Volvo Logistics ABProblem: Which parameters are important for logistic people to think of when they are going to choose a package?Which cost factors are included in the packaging cost?What kind of added value can an emballage supplier provide their services with?Purpose: The purpose of the project was to study the parameters that drives the customer's choice of packaging and the factors that influence the total packaging cost. The study also consists of a valuation of what an emballage supplier can offer to add value to their services.Method: The study is based on interviews with people who are working at Volvo Logistics and Volvo Car Corporation. Volvo Logistics provide their customers with standard packaging material, which they own and administrate. Volvo Car Corporation is one of their customers.

This report aims to examine the design of a passive house. The design addresses the selection ofmaterial, sizing and selection of both building services systems and building technical features suchas load-bearing framework and moisture control. Interior layout is designed for a family of twoadults and one child.A big part of the report is devoted to an in-depth comparison of three different wall constructions ofpassive house standard. The structures that have been compared are a lightweight timber structure, aheavier concrete structure and a sandwich wall of the brand Weber Leca. The report covers variousaspects such as air flow, wall thickness, the risks associated with the construction, U-value, thermalbridges, power consumption, price, and assembly costs.

In many products a compromise between ground clearance and the required space to store the product has to be made. This problem attracted the attention of the authors of this thesis.The objective of this project is to develop a functioning solution to a foldable wheel. The solution should be applicable to several types of product groups. A limitation for this work has been made so that the work only covers solutions for lighter vehicles.The purpose is to drive this project forward, so that a solution can be found. Furthermore the purpose of the report is to clarify how the authors proceeded to design and construct the wheel according to a fixed specification.

This report aims to examine the design of a passive house. The design addresses the selection ofmaterial, sizing and selection of both building services systems and building technical features suchas load-bearing framework and moisture control. Interior layout is designed for a family of twoadults and one child.A big part of the report is devoted to an in-depth comparison of three different wall constructions ofpassive house standard. The structures that have been compared are a lightweight timber structure, aheavier concrete structure and a sandwich wall of the brand Weber Leca. The report covers variousaspects such as air flow, wall thickness, the risks associated with the construction, U-value, thermalbridges, power consumption, price, and assembly costs.

The thesis presented in this report has been made on behalf of Scania and their basic frame design department with the subject to solve an implementation of a weight sensing system in the chassis. The system is supposed to be implemented in the seat springs, and the reason for this is that all the force will have to go through the weight sensing transducers. With all the force going through the transducers the weight sensing system will not be sensitive for the differences in tolerances from manufacturing. The transducers could be pre-calibrated to avoid a calibration of the whole vehicle after it?s completed from the manufacturing line.Weight sensing systems is today a reality in trucks with air springs.

The most common way to treat wastewater in Sweden today is by a combination of an activated sludge process and a chemical treatment. These processes are not very energy efficient and may not be the most environmentally friendly. That is why it is interesting to evaluate new alternative methods to see if they can be less harmful to the environment and help to a lower resource consumption. New techniques are tested in a pilot installation at Hammarby Sjöstad, Sjöstadsverket. To be able to evaluate these techniques in a wide perspective system analyses are conducted where different impacts can be considered, advantages and disadvantages in the systems.Five system structures for water treatment have been constructed in Matlab/Simulink in this study.