Abstract This qualitative interview study focuses on job coaching by examining what thoughts, views and opinions the involved parties, such as job applicants and job coaches, have of the contribution. The aim is to highlight the obstacles and opportunities by examining the expectations that exist from both parties as well as how to look at job coaching and its different areas. In this context, examine the similarities and differences between the two parties approach to the contribution. This is made possible through four interviews with job applicants as well as four interviews with job coaches. A grounded theory inspired approach was used to obtain the results of the study.

This thesis has been performed at Uddeholms AB with the purpose to investigate theparameters affecting the formation of inclusions during the manufacturing of a low carbonmanganese-steel.A follow-up, steel and slag sampling and evaluations in microscope have been done for a totalof five heats.The results for each heat have been evaluated in relation to the theory from the literaturesurvey and suggestions for changes in the process to reduce the amount of inclusions whichhave a negative effect on the steel quality have been given.The project extends over a large process where many parameters affect the formation ofinclusions. However, a tendency that a higher addition of alloys seems to increase the totalamount of inclusions before and after the vacuum degassing is seen.The majority of the studied inclusions seem to approach the composition of the top slag aftervacuum degassing. Ladle glaze may cause the inclusions which had a different compositioncompared to that of the slag.A high or low ladleage together with a high argon flow during vacuum degassing seems todissolve particles from the refractory which later on get trapped inside the inclusions.The floatation for two heats has been studied where a short floatation seems to give a higheramount of inclusions in casted material.In machined material so called stringers were found. The main composition of those stringerswas pure alumina. Inclusions with a composition of pure alumina were not found in the liquidsteel, thus the pure alumina inclusions must be formed during the casting.

The smelting process at Sapa Profiler AB in Sjunnen generates large quantities of waste heat which is absorbed by the cooling water when the aluminum is cooled down. This paper is the result of a Master?s Degree Project aiming to present the conditions for recycling the waste heat. The cooling water absorbs the heat from the aluminum at an average rate of 600 kW and the paper shows that it can be used to replace electrical power consumption for heating the production plant?s facilities.

The main focus for this essay is to describe the relationship between human and nature through a material investigation that takes its shape through sculpture. With the help of a fairytale-like story the reader can share the creation of the sculpture and how my thoughts flow through the process that will result in an exam project. Rooted in earlier projects I discuss the crash between civilization and the wilderness as well as talking about the likeness of the creative process and child play. I also discuss the body's place in the forest and the loneliness that we humans created that has cut us off from the rest of the creatures and plants in the forest. My aim is that in the final piece I will create a fiction place where these can be joined together again.

Syftet med examensarbetet är att ta del av förskollärares åsikter om och erfarenheter av materialets betydelse för barns lek och lärande, med fokus på ?smutsigt? material i innemiljön. ?Smutsigt? material är material som kan skapa oordning och kladda ner, t.ex. vatten, sand, lera, färg m.m.

This study is preformed at Westbaltic Components placed in Töcksfors Sweden. Themain target in this study is to make one of the company?s assembly lines better andmore effective. The assembly line constructs vending machines for different stores allover Europe.It will contain tobacco, snuff, cigarettes and shaving blades and many more similarproducts.The first step in our study is to locate the daily problems and find out a good way toreduce them and make them disappear. A good way to do this job easier was toconstruct a visualizing board.

Syftet med denna uppsats är att hitta en innovativ definition av begreppet interna kunder samt föreslå en implementeringsstrategi för en av den svenska matvarugrossisten ICAs lagerenheter. Vi har nått våra slutsatser genom kreativa studiebesök, interaktiva intervjuer, en innovativ workshop och litteraturstudier. Vi har utgått från leanfilosofin och teorier om kulturer, förtroende och kommunikation i organisationer. Inom samtliga områden har vi stött på kopplingar till inre och yttre effektivitet. Under intervjuerna upptäckte vi att ICA står inför vissa utmaningar när det gäller de anställdas förtroende, kommunikation och individualistiska tankesätt.

ABB Capacitors is looking to introduce LEAN within their organization. The purpose of this research is to suggest ways to improve the production planning in order to facilitate the company?s production processes. This should be done in accordance with the LEAN concept.Today, ABB will produce two of the customers? orders at the same time.

At Forsmark nuclear power plant a new course called "education in everyday safety" has been started in an attempt to improve the safety culture. The goal is to spread the of expectations and approach the maintenance management has set, to all employees working at the plants. During the course, theory is mixed with practical tasks to reach a common view how work should be done to achieve safety for the plant and the people that work there.The practical tasks are done inside "maintenance simulators". They are built inside 20 ft containers which contains two dummy pipe systems. On the pipe systems some valves, a flow meter and a pump has been installed.

In order to facilitate testing of anesthesia machines a patient simulator has been required by Maquet Critical Care AB. A patient simulator has been developed to reduce expensive and time consuming animal experiments and temporary lab arrangements. The patient simulator has been developed and designed to simulate human lungs with regards to anesthetic uptake, production of carbon dioxide and heating and moisturizing exhaled air.The system comprises a container and a test lung to simulate the volume and the dynamic of the human lung. The simulation of uptake of anesthetics has been implemented by pumping a fraction of the gas from the container through a bypass circuit with an active charcoal filter that adsorbs volatile anesthetics. The flow through the bypass circuit is generated by a pump and is controlled by a linear valve.The resulting performance of the patient simulator has fulfilled the requirements.

This report examines the industrialization of a newly developed household machine on behalf of Technogarden Engineering Resources in Karlstad, Sweden. The report is a part of the final course in the Bachelor Program in Mechanical Engineering at Karlstad University and takes place in spring 2014.An innovator, an investor and a engineering consultant firm have through collaboration developed a new type of gruel machine. The product is in its final stage of construction and is planned to be manufactured in a production located in Sweden, autumn of 2014.To compete against today?s trend in outsourcing manufacturing to low cost countries for better profitability, the industrialization of the gruel machine must be done with a minimum amount of resources in order to become successful, which also describes the problem of this study. Using pre-study material in form of Lean production literature, visiting a successful production site and gathering data from involved engineers a specification was developed which describes what this industrialization must achieve and which requests can be accomplished.

Till följd av globalisering och en växande konkurrens ställs det i dag allt större krav på organisationer. För att möta den hårdnande konkurrensen är det vanligt att företag implementerar olika kvalitetsprogram. Dessa förändringar ses som nödvändiga åtgärder för att kunna bibehålla marknadsandelar och vara konkurrenskraftiga. Genom att införa Lean-verktyg och arbeta med ständiga förbättringar minskar riskerna för att produktionen läggs ned eller flyttas till lågkostnadsländer.Som examensarbete har författarna valt att studera ett av dessa Lean-verktyg som används för ställtidsreducering. Verktyget benämns SMED och står för ?Single Minute Exchange of Die? vilket syftar till att öka maskintillgängligheten genom effektivare verktygsbyte mellan olika produkter.

I och med det enorma användningsområdet av datorsystem i dagens samhälle finns många typer av användare och uppgifter att designa för. Genom designriktlinjer kan utvecklare få referenser och guidning för att skapa användbara applikationer från början. På så vis kan tid sparas i utvecklingsprocessen. Från och med puberteten då människan kan anses vara vuxen ändras förmåga till andraspråksinlärning, trots detta finns det människor som lär sig andraspråk i vuxen ålder. Kunskap kring vad dessa skillnader beror på måste användas i designen av en andraspråksinlärningsapplikation för att tillgodose människans kognitiva förmågor.

This Master thesis has been carried out at Scania CV AB in Södertälje, in collaboration withKTH, The Royal Institute of Technology, Stockholm. The focus of this Master thesis isSetBased Concurrent Engineering(SBCE), with the purpose of answering the questions: what isSBCE, how does it work, and for what purposes is it applied.It was early established thatSBCE is often included as a part of Lean product development,which in its turn is often related to Toyota?s way of working. TheSBCE method includesworking with multiple solutions in parallel, eliminating weak alternatives throughout thewhole process. In opposite to a conventional product development process, where it iscommon one at an early stage tries to identify and choose the most promising alternative.Despite the appearance ofSBCE as a resource consuming method, figures from Toyotaindicates the opposite, thatSBCE is in fact a very effective way of working compared to othermore traditional methods.The process of this Master thesis was divided into three phases.

Title: The appraiser?s choice of valuation method ? factors that influences the choice of company valuation methodsSeminar date: 04/06/07Course: Master thesis in Business Administration, 10 Swedish credits.Authors: Anne Benedicks and Veronica ÖbergAdvisor: Eron OxingProfession of category: Financial analysts, auditors and company lawyers.Key words: Company valuation, valuation methods, cash flow analysis, comparative valuation, the net asset value method.The Main Issue: What is of decisive importance when choosing a special company valuation method?Purpose: The purpose of this paper is to identify, analyse and evaluate the most common methods of valuation for financial analysts, auditors and company lawyers and those factors that influences the choice of method.Method: A multiple survey has been implemented for the actual profession categories. Primary data was collected through semi-structured interviews and a questionnaire survey.Theoretical: The theoretical frame of reference is based upon the paper?s dependent variable, i.e. the role of the appraiser.