Industrial buildings are increasing all over Sweden. Farmers are building new modern facilities and the government chooses to build new halls to invest i youth sports. Glulam is the most common framework but there are limitations because of the transport. Therefore, there is a need to develop new solutions to increase the use of glulam.The maximum torque in the eaves was found in the frame with a roof pitch of 18 degrees and a wingspan of 25 meters. Using hand calculations according to Eurocode and comparison with the computer software StatCon, the maximum torque, shear force and utilization rate is calculated.

AbstractConcrete foundation slabs are usually exposed to unilateral drying during the curing process. The unilateral drying causes an axial shrinkage and a concave curvature of the construction. The curvature results from the fact that the upper part of the slab is drying and shrinking faster than the lower part. This is called gradient shrinkage.A problem occurs when the slab is considered fully restrained by adjoining structural parts. The deformations caused by axial contraction due to the constant part of the shrinkage and the curvature caused by gradient shrinkage of the slab are then prevented by the fact that the slab is fully restrained.

This paper deals with variations in the osteological material of dog (Canis familiaris L.) from the Mesolithic Scania, southern Sweden. The general aim is to discuss the use and specialisation of dog during the period, and differences or relations between cultures and traditions within the Mesolithic period. The study is based on a analysis of the bone material from the sites; Ageröd I:A-D, Ageröd I:H-C, Bredasten, Bökeberg III, Hög, Löddesborg, Ringsjöholm, Segebro, Sjöholmen, Skateholm I-II and Tågerup, phase 1-3, with datings from Late Maglemose Culture to Early Ertebølle Culture. The seminar paper also includes descriptive statistics of the osteometrical data of Denmark, from several studies of Degerbøhl (1927) and Noe-Nygaard (1995, 2003). The study is focused on the relation between size, robusticity, muscle grooves and ligaments of mandibula, tibia, radius, humerus, femur and metacarpalia/metatarsalia.

The purpose of this study is to achieve an understanding of how a CE- marking process is conducted and to identify the relevant factors that must be considered in such a process. We have conducted our study at Lo?vhults Svets & Smide AB (Lo?vhults) in Skruv, Sma?land Sweden, which are manufacturing brackets for small covering constructions.To understand how a CE-marking process is conducted several documents and provisions have been reviewed to achieve a basic understanding and insight of the subject. It thus led to that guideline ETAG 015 were studied and the factors to be considered in the CE-marking of brackets were identified. Together with Jan-A?ke Johansson at Lo?vhults we agreed on four different brackets to investigate for a potential CE-marking.

 AbstractThis Master?s thesis analyses the dynamics of the medieval counterweight lever engine, ortrebuchet, a type of mechanical artillery. The purpose is to study the differences between different types of these machines, and see if computer simulations can be used to validate preserved advice on construction. Simulations include machines with a fixed counterweight, a hinged counterweight and a combination of both counterweights.Due to the almost complete lack of archaeological finds and insufficient historical source material there are still, after more than a century of research, many unanswered questions concerning the design and performance of these machines.The present study is based on an analysis by Jahsman (2004). A more detailed mathematical model employing Coulomb-friction is used.

The energy consumption continues to increase as the use of electronics and energy consuming equipment increases. The use of fossil fuels has to be phased out for this to be sustainable in the long run while the use of renewable energy continues to increase. A renewable energy source is solar energy but the production of heat and electricity are today very expensive compared to other energy sources and an important task for the solar energy market to grow is therefore to minimize the production cost of the solar collectors while increasing its efficiency to produce heat and/or electricity. One way to convert solar energy into heat is by using solar collectors and electricity can be produced by utilizing the produced heat, or by applying solar cells.This thesis aims to recommend a reflective material for the next generation solar collectors from Absolicon and to recommend a commercially available coating for the receiver tube of the solar collector. A market study has been carried out to investigate the cost-related aspects along with the optical and durable aspects for the optical material of the solar collector.

This is a final year project considering constructional techniques for joining cavity walls. The project is related to an ongoing scientific programme about the restoration of The City wall of Visby located on Gotland. The programme was set by Riksantikvarieämbetet as a reaction to a collapse of the outer masonry wall shell which took place in February 2012.The City wall of Visby is a medieval fortification built out of limestone during the 13th century. The wall is constructed as a cavity wall with two separate masonry shells connected to each other through an intermediate core. During the 14th century the wall was heightened which lead to a higher stress, especially in the outer wall face.

The thesis project is accomplished during winter and spring 2008 at Karlstad University at the faculty of technology and science. The tutor at Karlstad University is Nils Hallbäck and the examiner is Hans Johansson. Rolls-Royce at Kristinehamn in Sweden is the initiator for the project. The thesis project title is design of the blade bolt joint on Kamewa CPP. CPP stands for controllable pitch propeller.

This thesis work has been performed on request by SWT (Scandinavia WeldTech AB). SWT manufactures, develop and sell ready to assemble building systems for concrete rafter beam applications. The beams in this system consist of a u-beam that is welded to a flange. To be able to fill the beams with concrete there is holes in the beams top end. The holes are made in a ?punching machine?.  These holes are cut out and the remaining steel piece is bent down in the u-beam.

Echinococcus multilocularis är en helmint med indirekt livscykel. Parasiten lever i tarmen på sin huvudvärd, framför allt räv, som utsöndrar ägg med faeces. Äggen tas upp av en mellanvärd, migrerar till levern och utvecklas där till ett larvstadium kallat metacestod. Mellanvärdar är framför allt vilda smågnagare, men även andra djur inklusive människor kan infekteras. Hos mellanvärden ger E. multilocularis upphov till en sjukdom kallad alveolär echinococcos.