The purpose of this project has been to cut production costs for the fascia panels ofGetinge?s largest autoclaves. The cost for the stainless steel plates currently used is veryhigh. An alternative material solution could cut costs significantly.In addition, improvements have been made to the instrument tower which is a central partof the fascia panel. As a result of the new modular design in a new material theinstrument tower has been improved in several aspects..

The purpose of this study was to compare Glasgow/ Scotland and Malmö/ Sweden concerning their efforts towards youth unemployment, in sense of the social policy related to the organization. We have particularly concentrated on; the direct and indirect political strategies for young unemployed; what specific efforts that are provided on a local level; finding explanations to the design of these efforts and describing the development of youth unemployment and labour market- policies in each country. We have based our study on literature studies and six qualitative interviews conducted with representatives from different organizations and the municipality in Glasgow and Malmö. The outcome of our essay showed some differences in the political strategies. Scotland work closer to the employers and labour market compared to Sweden whose policy more promotes education.

The aim of this study was to develop a simple model for calculating stock costs for bio fuel at Billerud Karlsborg and subsequently recommending a suitable stock level of bio fuel. The stock components considered in the model are GROT (branches and tops), bark, dry wood chips, raw wood chips from barking and sawdust. The calculations are based on a probability distribution of historical deviations between ordered and delivered volumes. The model presents two different ways to manage the supply in case of irregular deliveries. The first way is to stock enough volume to cover the deviations and the second way is to compensate with a quick purchase from the spot market (at extra high purchase prices).

This thesis examines the emissions costs of Swedish aviation and their degree of internalisation under current economic instruments. The results show that the degree of internalisation spans from practically zero for a long-haul flight to 6 per cent for a typical domestic flight, where the climate cost, including high-altitude impact, makes up the main part of the cost. To inform evaluation of the consequences of this underinternalisation, or attempts to correct for it using price instruments, the price and income elasticities of international leisure air travel from Sweden are estimated using household expenditure data and two different price measures. The resulting elasticities are very high ? 2.03 or 2.04 for the income elasticity and -2.53 or -1.88 for the price elasticity ? and should be interpreted cautiously due to data limitations, especially for the price elasticities.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis investigates similarities and disparities between Swedish and Polish Labour Law concerning dismissals due to operational requirements and group redundancies. The study focuses on three important elements where the employers? liberty is legally infringed upon in a procedure of notice. These elements concerns the legal conditions of notice that must be fulfilled, the rules of the procedure and the rules for employment protection that is granted in connection with dismissals due to operational requirement or group redundancies. In the thesis there is a comparative map that outlines the most important rules within the Swedish and Polish legal systems concerning the subject.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

Structuring education so that students can discover connections between schoolwork and their everyday lives is a crucial task for a teacher. This is especially true in today?s school system that seeks to foster a spirit of lifelong learning, since educational motivation depends on being able to connect to the tasks at hand. In a system where these connections are not present, students will be motivated only by institutional mechanisms such as test results and grades. This leads to them using a number of techniques for ?optimizing the system? by getting maximal results for minimal effort. This essay looks at two pedagogical movements that aim to decrease the gap between schoolwork and students? reality.

This paper examines how organizations work with their recruitment. The organizations in thispaper are mined in the trade of recruiting and staffing. The paper will further influence howorganizations work or will work with recruiting through social medias. It describes therecruiting process in the traditional way and what costs it brings. The next part is a descriptionof network and the importance of networking in a general way.Our results demonstrate that social medias probably will stay as a complement to other moretraditional methods and will not be an own recruiting method.