Uvån Hagfors Teknologi AB (UHT) has developed a process ? GRANSHOT® ? for quicksolidification of metals in water baths. In the process liquid metal is splintered ? granulated ?into small drops. The drops are rapidly cooled in a water bath where all the heat energy from theliquid metal is transferred into the water.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The purpose of the study was to investigate the use and losses of energy in an existing older building. Another purpose was also to look through various options for heating systems with renewable energy in the building. The aim was to reduce the use and losses of energy. The first step was to study the related electricity bills of the building and also perform measurements and calculations of the building envelope and ventilation. The next step was to find out the possible actions for energy saving by performing measurements and calculations.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

Energy awareness is growing among the Swedish population and a one­?to­?two-family dwelling can save energy. The purpose of this paper is to design a tool that helps these home owners reduce their energy costs.The paper develops a model that gives them an indication of how much energy they can save. For the majority of homeowners, the next step in the quest to reduce theirs is most likely an energy audit. Therefore, information to help home owners to get a good energy audit performed is included in the model.A prototype running the operating system iOS is created and validated against existing models, as well as an energy audit. .

Abstrakt -  As energy prices rise, energy-saving in buildings is becoming increasingly important. By applying different construction and installation technologies, to new buildings the energy consumption can be reduced effectively, compared to similar existing buildings. These technical measures are often an investment in the long term and will reduce energy costs significantly. The purpose of this report is to show how to reduce energy consumption in a small house. It is presented in this report that both building's technical saving arrangements (the sealing of a building) and an installation technical arrangement (changing from the F-system to the FTX-system) would reduce energy consumption in newly built detached houses, if compared with a similar existing house but without these technical measures. The report presents also detailed calculations showing how much energy an existing 2-storey house, built in the year 2007 in Eskilstuna, consumes and how much energy would be saved if these corrective measures were applied to a new building. It is also reported how much money would be saved each year over a 10 year period if the measures were applied. The results show that both solutions are a good investment in the reduction of energy consumption and hence the cost involved. Keywords: energy, heat energy, infiltration, FTX-system, free temperature effectively. .

The primary function of a mixer is to keep a fluid in constant motion. All mixing applicationsrequire varying degrees of small-scale turbulence and bulk flow. The performance of asubmersible mixer is measured by the thrust that it produces, while the strength of the bulkflow is dependent on the total amount of installed thrust.In a mixer, the fluid quickly flows past the propeller, and as a result, the current is mainlyaxial. The fluid will also obtain a rotating velocity, or a swirl, though this is significantly lessthan that of the propeller. During the process, the total amount of energy increases in the formof static pressure and kinetic energy.

This report will show the energy usage of Hotel Princess in Sandviken, Sweden. When the hotel changed owner an examination of the hotels heating, ventilation and sanitary systems were done. The report showed flaws in the ventilation system, and is why the new owner wanted a closer look at the energy use of the hotel. The original building was built in the 1930s and two major extensions have been built, one in the 1950s and the most recent in the 1980s. An assumption made is that the building parts were built to the restrictions during the time. Activities on the hotel include sleep over, conference, night club, massage and swimming in the hotels pool section.

Miljonprogram is a Swedish building program from 1964 to 1975. During that time about a million homes were constructed. Now, almost 50 years later, they are in desperate need of renovation. In order to fulfil the Swedish environmental objective to decrease energy consumption 50 per cent until 2050, considerable housing stock built under the Miljonprogram has to be renovated.Focus in this thesis is on the building services and theirs profitability that can decrease energy consumption in households build during the Miljonprogram. Building construction is not considered in this report.

En jämförelsestudie har genomförts mellan två värmesystem. Analysen har genomförts med ett flerbostadshus som referensfasighet. Fastigheten är lokaliserad i Södertälje kommun. Analysen går ut på att bestämma vilket värmesystem som är fördelaktigt vid renovering av äldre flerbostadshus med avseende på energi och kostnad. De systemen som har behandlats är ett centralt värmesystem med motströmsvärmeväxlare och ett centralt värmesystem med frånluftsvärmepump.Det centrala värmesystemet (Eq aggregat) är ett centralt från- och tilluftssystem med återvinning (FTX system).

Understensho?jden is Stockholm's largest eco-village which was built in the early 1990s with the vision of enabling ecological living for people. However the ecovillage is no longer considered as environmentally friendly because of its relatively high energy consumption, and non-updated energy system. The purpose of this study is therefore to investigate how Understensho?jden should reduce their energy consumption and upgrade its energy system by using Blower-Door, IR-camera and Design Builder.

AbstractEmbla 5 is an office building which has done a large improvement. The clients of this building has made an order of WSP and the student Anders Kempe to calculate the use of energy for the building, and after that result proposing further measures which can decrease the energy use of Embla 5.The ground for this report is when calculation of the present energy use of the building is stated. To make that information of a number of parameters such as envelope, the heating system and ventilation has been located and set in to the simulation program IDA ICE which calculate the energy use.To improve the energy use further this project has been concentrated to change the system of ventilation. Today the ventilation system is of the kind CAV (constant air volume) and the air flow is dimensioned for after recommendations from BBR and Arbetsmiljöverket in the office spaces. Consider that Embla 5  is an office building where the people only staying for 8-10 hours/day so was the ide to see how much energy saving if the air flow is reduced the time people not being in the building.

The energy sector is facing an impending paradigm shift. Today?s technology enables the end-user to generate their own energy locally at home. Furthermore, recently developed storage technologies make it possible to balance energy demand with stored energy and integrate district heating with the local power grid. This means that in the future heat and electric power will interact and energy flows is converted over energy boundaries.

The aim of this study is to increase understanding about addiction recovery. More specifically, we want to know what people who have had problems with alcohol and/or other drugs perceive as helpful and important for their recovery process and how we can understand this process.The study was conducted by means of qualitative semi-structured interviews with four people who have had alcohol and/or other drug problems. The analysis is based on a transtheoretical model of change from addictive behaviours, coping, interactionist theories and also a recovery perspective, inspired by research on recovery from mental illness . Main findings are that recovery from addiction can be understood as an individual process that takes place in a social context and can follow expected phases, although there are large individual differences in the process. Through the recovery process it has been of importance to the participants in the study to redefine themselves and their problems, get support from others, find ways to cope with their problems, get involved in meaningful activities and to expand their social roles.