In Sweden there are 1894 small-scale hydropower plants in operation, which together generate 4.3 TWh of electricity per year according to Swedish hydropower compound (SVKF, 2011). This corresponds to the annual consumption of about 860,000 Swedish households (based on an annual consumption of 5000 kWh). In the mid-1950s there were around 4000 small-scale hydropower plants in operation in Sweden before cheap fossil fuels and uranium competed with them, in the current situation only 1,894 of these are in use. If slumbering small hydropower plants once again would be taken into use and some new ones are built, we would be able to extract about 7 TWh of renewable electricity from these annually in Sweden, representing about 1.4 million households.The thesis intends to calculate and construct a hydroelectric power plant at the existing dam in Olofsfors and give suggestions on how the power station should run during the time that fish migration is greatest in Leduån.The turbine and generator to the station in Leduån at Olofsfors is designed by the height of the fall and the water flow through the dam. The turbine selected for the station is a CK-1000RM turbine with a 4-pole 250 kW generator from Cargo & power turbine Sweden AB, which is expected to deliver 1.2 GWh per year.

The exhaust arrangement on a Scania V8 consists of one manifold at each bank connected to a twin entry turbine (8-2-2). A study in GT-Power has shown improved performance and reduced cylinder to cylinder variations using two manifolds at each bank in combination with a single entry turbine (8-4-1). This thesis work analyses the difference in performance shown in simulation and verify it by engine test.The initial work was focused on simulation in GT-Power. Investigating how exhaust manifold volume and pulses effects the turbine efficiency and the mean effective pressure during the gas exchange. To verify GT-Power simulations four engine tests with different exhaust arrangement have been made.The results from GT-Power simulation indicate that a larger exhaust volume improve the turbine efficiency.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

War has for all through the years adopted various guises and been performed by various actors for a wide variety of destination. But what is really a war? Why is war fought? How is war fought? By whom is war fought? Machiavelli, Clausewitz, Kaplan, Kaldor, Creveld and Krulak are just a few among others who have made valiant attempts to explain war and its nature. What did they find? This essay maps out their studies in the hope of finding some kind of continuity that can give a clearer picture of what war really is.

AbstractThis thesis is the final part of the Innovation and Design Engineering Programme (180 ECTS credits)at the Faculty of Health, Nature and Engineering Science at Karlstad University. The extent of thisthesis is 22.5 ECTS credits and has been performed independently by Hannes Jernberg during thespring of 2013. Metso Paper Karlstad AB is the task maker of this project, and Arvid Johansson is thecompany Representative. Metso Paper Karlstad AB is one of the world leading developer andmanufacturer of tissue paper machines.In the current situation, the company has developed and patented a power management systembased on a Cross Flow Turbine. The current construction is limited to a paper width of 2.9 meters.The company wants to take advantage of all the opportunities provided by the patents, to develop aturbine solution paper machine with a paper width that is wider than 5.5 meters, and give the abilityto manufacture paper for lower energy consumption which is an important part of the production asit is very energy intensive.Problems arise with the increasing length of the turbine, ultimately resulting in that the deflectionbecomes too big and that the momentums, due to the increased torque the turbine blades breaks.By applying the design process, this work has resulted in a number of potential solutions to theproblem.

In several countries that have been early in the development of wind farms, there is today a second hand market for the used wind turbines. The European Union (EU) has established a waste hierarchy in order to minimize throwaway mentality. The second hand market is a part of this as the steps are to minimize, reuse, recycle, extract energy and landfill.In order to promote the development of renewable energy, there are energy certificates for the producers that provide it, wind power being one type of renewable energy. After 15 years the energy certificates for a specific wind turbine are no longer paid, and after that there are several different scenarios for the wind turbine. The scenarios investigated in this bachelor?s thesis are export of the wind turbine to countries that are not as far along as Sweden in their development towards renewable energy, selling in Sweden to individuals, and recycling of the wind turbine, as it mostly consists of metals and therefore is recyclable.

A large number of rivers in northern Sweden have hydropower developments that cause negative effects on both up- and downstream migrations of anadromous species like Atlantic salmon. So far, most attention has focused on the hindrances of adult fish during their upstream spawning migration. However, since turbines in power stations cause losses on downstream passing fish, the focus on negative effects on smolts has increased. The aim of this study was to compare three different causes of losses of salmon smolts passing downstream through a power station area in the flow-controlled River Åbyälven in northern Sweden.A total of 61 wild salmon smolts were caught and radio-tagged in the River Åbyälven during their downstream migration in June 2009. The salmon smolts were released at three locations, 1.1 km upstream from the power station, in the turbine intake and in the upper part of a fishway, acting both for up- and downstream fish passage.

This final thesis contains three major parts, which all have been time demanding:* Designing and construction of a small wind turbine.* Designing and construction of an electrical system.* Thesis with fundamental facts about wind, wind power and design.The thesis contains basic theory in wind power and the energy systems it can be combined with. Different types of wind turbines, which components they consists of and important issues to consider when designing is also mentioned. In the end of this report the technique of our wind turbine will be presented. In the end you can also read about our experiences during the time of designing and construction..

Simulation is a vital tool during development of JAS 39 Gripen, since money and time can be saved.The Auxiliary and Emergency Power System, AEPS, is a subsystem of the secondary power system in Gripen. It has the function of providing the aircraft with electrical and hydraulical power before activation and after deactivation of the main engine. The system also functions as backup in case of a safety critical problem in the main power supply system. The system basically consists of a control unit and an auxiliary gearbox. The gearbox is driven by an air turbine.

AbstractThis report describes our ten week long thesis work which is the last task in our education in mechanical engineering at Linköpings University. The project has been performed at Siemens Industrial Turbomachinery AB?s service department. The company which is located in Finspång produces, sells and provides service for steam and gas turbines around the world.The purpose of this project is to help Siemens develop their maintenance programs for two of the auxiliary systems which are a part of the complete steam turbine system. These are lube and control oil systems.The project is restricted to two of Siemens maintenance products, No Stop Check (NSC) and the annual Safety Inspection (SI).

In this thesis a possible cost effective runner change of some of the units in the hydroelectric power station Olidan is investigated. The possibility to drive a unit at the same efficiency point through a change of the turbine shaft speed and the rate of discharge is tested. Furthermore the theories behind model testing, determination of efficiency increase from model to prototype and efficiency measurements shall be discussed and analyzed with Olidan as a starting point.A predicted curve has been built on information from model tests and field measurements on the existing runners and runner data from the test of the new model. The predicted curve shows the difference in efficiency between an existing runner and a modern one. It is the difference in efficiency that is used in the calculations that are to show whether changing to a pair of new runners will be cost effective or not.

I denna rapport utreds olika metoder för att kunna reglera vattennivån i vattenkraftverket Avesta Lillfors i Dalarna. Två kraftverk ligger endast 900 m uppströms och detta gör att svarstiderna blir korta och regleringen blir lätt nervös. Att använda sig av vattennivåreglering i ett kraftverk för-enklar dess styrning då anpassning till inflödet sker automatiskt.En flödestabell har tagits fram genom mätningar i turbinen, med hjälp av Winter-Kennedy-metoden. Denna tabell används för att kunna fram-koppla regulatorn och därmed dämpa stora variationer i inflödet. Dessu-tom har en modell av älven skapats och testats med en återkopplad PID-regulator.

In connection with the property crises in many countries, caused by the financial crises, people are now more aware of the risks involved in poor property-investments. The unusually cold winters along with extreme prices of electricity in Sweden in recent years has also contributed to increased interest in energy-efficient buildings.The process of developing a modern family home in Kiruna, Sweden is presented the first part of this paper. The house has been designed to withstand very high stresses from snow, low energy consumption as well as a high standard of living comfort. Aspects of the house covered here involves everything from construction, heating and ventilation to sanitation. Each of these areas is presented based on their underlying, scientific methods or theories.

The report begins with a general inventory of possible technical faults in a hydropower plant and of possible fault indicating measurements. Then an investigation is made concerning a few different faults. Based on this investigation a choice on seal box condition and water leakage is made as problem for a more thorough examination, in which it is concluded that the turbine water leakage is larger when the turbine is put into operation. The examination ultimately results in a computer alarm for faults related to the seal box. Finally a few things are mentioned about flow measurement and pressure measurement in relation to the project as a whole..