This report is written on the assignment by Nexans IKO Sweden AB in Grimsås which is a cable manufacturing company. Nexans IKO Sweden AB was in need of help to examine possibilities for saving energy by saving compressed air, in first place by using the compressed air more efficient. The task was to determine the present situation, making the airwipe stations more efficient by reducing the consumption of the compressed air and in turn save money. Even the aspects of the working environment were discussed as the noise levels from the pneumatic systems and engines are usually high. A schedule over the airflow in the factory and the inventory over current airwipessituation was made.

In hydropower plants it is necessary to always have local power supply. Therefore, the plants are equipped with batteries as stationary back up power. Vattenfall Vattenkraft is using lead acid batteries but has been investigating alternatives to replace them. The aim of this study is to investigate the potential of using Li-ion technology as back up power.The study showed that Li-ion batteries have many qualities. The Li-ion technology will decrease the space and maintenance demand.

This master thesis investigates the possibilities of using GPS-information from trains to create a model of a railway system, register the routes of the the trains and predict how the trains will travel in the railway system.The thesis work was done at Icomera AB which is a company that specializes in internet connected vehicle solutions.We describe how the GPS-information is sent from the trains in the form of samples and investigate limitations and possibilities with the available information. About three million samples from 83 SJ-trains were analysed and the samples were filtered with the intent of removing erroneous information. We here found that about 30 % of the samples from the trains were unreliable.A solution for how the samples from the trains can be used to create a model of the railway system traveled by the trains is presented. We use a large set of historical samples and use cluster nodes and Hermite curves to generate a graph that represent the railway system with stations, nodes and the railway itself. A fully automatic solution is not presented since it did not fit into the time frame of the thesis; instead we created a simple tool which can be used to manually finish the model of the railway system.Furthermore, we describe how the railway system and the samples from the train can be used to register the routes the trains travel.

This project has revolved around finding better ways of overseeing vibrations of the gearbox at a wind power station. The gearbox has been a huge problem at the stations located at Gässlingen and the sooner the warning of an incoming breakdown is at hand the more money you can save from preparations. The work has been carried out together with Askalon AB in cooperation with consults from ÅF. Askalon is a company with a department focused on overseeing vibrations and it is in collaboration with that department the work has been carried out. During this work, new positions for the sensors and new methods of gathering and analyzing data have been worked out. This was then implemented at a wind power station to be tried out on site.

In this trial we used QualispermTM as an objective method of measuring stallion semen. Samples of semen were analyzed before and after centrifugation. Motility and concentration were statistically analyzed. During the trial all the objective mesaurments were compared to a subjective method. The advantages of QualispermTM compared to older CASA- systems is it´s ability of measuring a greater amount of spermatozoa while it also grades them into different subpopulations. These subpopulations have different qualities that decides their capacity of fertilization. The results showed that this objective method might be used practically. Although, there are still some disadvantages, such as high costs and the necessarity of accurat training of the handler. If it´s possible to prove further relevant results that also are statistically correct, this could prove the usefulness of QualispermTM as an objective measurment method in the daily work at gestuts and stallion stations, thus giving the staff a reliable instrument in assisting the work for an improved horse breeding in Sweden, improving both in quality and economically..

This master thesis investigates the possibilities of using GPS-information from trains to create a model of a railway system, register the routes of the the trains and predict how the trains will travel in the railway system.The thesis work was done at Icomera AB which is a company that specializes in internet connected vehicle solutions.We describe how the GPS-information is sent from the trains in the form of samples and investigate limitations and possibilities with the available information. About three million samples from 83 SJ-trains were analysed and the samples were filtered with the intent of removing erroneous information. We here found that about 30 % of the samples from the trains were unreliable.A solution for how the samples from the trains can be used to create a model of the railway system traveled by the trains is presented. We use a large set of historical samples and use cluster nodes and Hermite curves to generate a graph that represent the railway system with stations, nodes and the railway itself. A fully automatic solution is not presented since it did not fit into the time frame of the thesis; instead we created a simple tool which can be used to manually finish the model of the railway system.Furthermore, we describe how the railway system and the samples from the train can be used to register the routes the trains travel.

Our report procedure identification of instability and disturbance in an automatic manufacturing line of processing and assembling of chair sliding rails at Sapas manufacturing department in Vetlanda.To obtain a stabile ground we have mapped the material flow to receive a comprehensive view and to visualise connections.We have examined cycle times at different stations in purpose to identificate bottlenecks. The result of our examination showed that the bottleneck of the line was the brush station. This leads to that the expected bottlenecks identificated by Sapa gets a delay time and by that a longer cycle time.Interruptions has a clear negative influence at the line performance so we have also assemble data through the operators report list and compiled these in order to find out the interruptions effect on the line. The outcome during our assembled period was that the reported interruptions corresponded about 30 percent of the total available production time. This has a clear negative effect on the line productivity and efficiency as we have calculated in order to get the present status..

The purpose of this thesis work was to develop an automatic fault detection system for surveillance of bearing temperature in hydropower turbines. The parameters used except the bearing temperature were cooling water temperature and cooling water flow. A simple static model based on data sampled every minute was developed to estimate the bearing temperature. Then a detector for detection of change in bearing temperature based on the CUSUM-algorithm was designed. Since the amount of data was very small the developed model was too uncertain to be used in a working system.The designed fault detection system showed to work well for the available data.

Extended Producer Responsibility (ERP) is a form of product take-back regulation that requires the producers to manage their products at the end of life. By internalising the products? entire life cycle costs into the market price the ultimate objective of such regulations is to reduce the environmental burden from the products. This Master´s thesis seeks to examine if the total life cycle cost of a product actually is borne by the producer, and if not, predict who will then take this cost. This is done by analysing the market for take-back activities in three different categories of products; electrical and electronic equipment, cars and wind power stations.

This Master Thesis discusses the development of bids for regulation power with consideration of change of discharge. The study was initiated by Vattenfall PD and is a limited part of a substantial development project at the same division. The background of the project is the new demands from SvK, which among other things includes more detailed regulation bids. As from the 1st of November 2008, the regulation bids are supposed to be calculated regarding each specific regulation object, something that is defined by SvK. These new demands changes Vattenfall?s conditions and will increase the need for detailed knowledge about available regulation power and costs for regulation.In this study a strategy for regulation bids was developed.

Ericsson develops a new stripline directional coupler. Its design is described in appendix B and differs from the directional couplers Ericsson uses in current products. The new directional coupler will be used for transmission power measurement in future UMTS 3G base stations.The most important parts of directional coupler theory are presented. It is necessary to study this theory to understand how the coupler works and how it should be designed to get good performance.Optimal directional coupler termination component values to get high directivity and broad directivity bandwidth have been investigated.The trim screws trim ranges have been studied.A simple analysis of serial production performance when termination component tolerances are taken into consideration has been done.The resistance components reactive (inductive/capacitive) characteristics at 2.14 GHz have been analyzed.The directivity performance limitations of the directional coupler, when Ericsson?s band pass filter is connected, are investigated.Design changes leading to better performance are proposed.

An ethnographic study loosely informed by the theoretical framework of distributed cognition was carried out in order to describe how mariners have adopted the Automatic Identification System (AIS) in their work practice, or"made the technology their own". AIS is a transponder-based identification and communication system that allows ships to automatically identify and track each other. In addition to facilitating the identification and tracking of ships, objectives behind the introduction of AIS are to"simplify informational exchange", and"provide additional information to assist situation awareness". Participant observation and interviews were made at four different ships, as well as at two shore stations. A focus group was also held at a maritime conference.

According to the European Union waste hierarchy, waste should first of all be minimized. Reuse and material and energy recycling come next. Lastly the waste should be thrown at the refuse tip. In the inner city of Stockholm waste handling can be done in various types of ways. The solutions vary as a result of the type of architecture of the building and its condition.

GPS is perhaps the future in agriculture. The next years will show it but the precision becomes only better and better and the number of users becomes only more and more. This work shows experiences from today's users and how the profitability can be improved on a farm with normal plant cultivation. The aim is to show how big the actual advantage can be to have a GPS and how good precision there is with the equipment. John Deere and Trimble are the big producers of GPS equipment to the agriculture.

The purpose of this bachelor degree thesis is to analyze technical issues associated with an implementation of a low sloping trash rack with narrow spacing. A hydropower plant in Umea?lven was used as a case study. The basis for the study was a model where trash racks were dimensioned for inclinations between 25 and 45 degrees. Corresponding head loss, durability and water speed through the rack were then determined for each inclination.