This report deals with the modeling of a part of the communication system based on the IEEE 802.11a standard which represents the next generation of wireless LAN with greater scalability, better interference immunity and significantly higher speed, up to 54 Mbps. 802.11a uses Orthogonal Frequency Division Multiplexing (OFDM) where modulation is performed by an IFFT and the demodulation by an FFT. After modeling the FFT in Matlab and C, the FFT implementation has been validated using a soft microprocessor core by Xilinx (Microblaze) and the results were compared..

Hägglunds Drives in Mellansel, Sweden, manufacture radial piston hydraulic motors foremostwithin applications in the industry. These motors have several sliding contacts, one of these, isthe contact between piston ring and cylinder bore. The radial piston hydraulic motors advantageis to produce high torque in very low rotation velocity, this result in that the maximum slidingvelocity between piston ring and cylinder bore, during the whole stroke, is very low. Theconsequence of this low sliding velocity is that the contact between piston ring and cylinderbore, during the whole stroke, is bound to the boundary lubrication regime. This result in, thatthe piston ring is exposed to wear, thus affect the service life of the complete hydraulic motor.To minimize wear of piston ring, it is essential to determine the oil film thickness between thepiston ring and cylinder bore.

At Forsmark nuclear power plant the rather old-fashioned software COPTA is used in containment safety analysis. There exists a desire within the organisation to introduce a more modern software with ability to more detailed modeling and increased usability.The goal of this thesis was to evaluate the software APROS in containment safety analysis. APROS models describing one of the containments at Forsmark NPP have been developed. Two simulations of typical containment incidents, one of them a large pipe break, have been made where containment safety parameters such as pressure and temperature are studied. Results are analyzed and verified against results from corresponding COPTA models.

Learning organizations and organizational development are interesting subjects that does not examine municipal organizations and private organizations an equal amount.  Furthermore, there exists little research on the effects of competence development for individuals in a leadership role within organizations. Because of this, we wanted to examine the impact of competence development in business modeling and how it affected local government activities. Competence development is used by organizations to develop their business and achieve a greater competitive advantage, but does competence development for individuals in a leadership role lead to organizational development? This paper examines competence development in the form of a business modeling course via the Bitstreamproject and the effects that occur within three municipalities as a result of the competence development. By interviewing three participants and four coworkers within different municipalities and studied the data from the Bitstream project, we can not conclude that competence development within business modeling leads to organizational development, only that it exists a tendency for it.

SammanfattningModular Management AB (MM) är en konsultfirma som arbetar med att implementera Modulära produktarkitekturer hos produktutvecklande företag. Företaget grundades i Stockholm år 1996 där huvudkontoret ligger än idag. De är världsledande inom sin genre och på grund av stor efterfrågan har kontor uppförts även i USAoch i Kina.Detta examensarbete är utfört på uppdrag av MM och har genomförts med hjälp av deras kunder i Finland samt kundens CAD-leverantör. Det behandlar modularisering och hur detta realiseras med hjälp av datorbaserad konstruktion (CAD). Detta är en MMs produkter och den kallas Modular Modeling.

Two ecological models of nitrogen processes in treatment wetlands have been evaluated and compared. These models have been implemented, simulated, and visualized in the Modelica language. The differences and similarities between the Modelica modeling environment used in this thesis and other environments or tools for ecological modeling have been evaluated. The modeling tools evaluated are PowerSim, Simile, Stella, the MathModelica Model Editor, and WEST. The evaluation and the analysis have been performed using McCall?s factors for software quality (McCall et al, 1977), a correlation analysis and the Constant Comparative Method (Glaser&Strauss, 1999).

The task in this thesis is the steering of one of Saab Bofors Dynamics robots using Sliding Mode Control, a method they never used before. The robot constitutes a system which in addition to perturbations and uncertainties due to modeling imprecision, hold the difficulty of being highly time variant. In order to be able to keep required performance with uncertainties and modeling imprecision present, the use of robust control methods like Sliding Mode Control is necessary. SMC is based on the states of the system being forced to stay on or in the direct vicinity of a hyper plane in the state space which is chosen in a way that gives the system dynamics desired properties. Other advantages with sliding mode are reduced order dynamics on the switching surface and total insensitivity to some uncertainties and perturbations.

This report treats a Master Thesis performed at Scania CV AB. The task was to create a computer model of a hydraulic actuator system in the software AVL Hydsim. The system consists of two spring-loaded masses with surrounding hydraulic components. The purpose of the model is to study phenomenon and problems in the system, as well as to be a support in the development of the system. It is not supposed to be used to study absolute values in its current form.

Hydropower is the largest renewable energy source available in today's society. Operation and production is handled by high-tech electronics. This thesis is done on behalf of Statkraft Sweden AB who wants to explore the possibility of replacing the hydraulic cylinder with an electric actuator, generally as well as a case of a small power station on the river Nissan. Whether it is the chaplain or francis turbine vanes are actuated by hydraulic cylinders. Because of Gustavsberg hydropower is inconstant operation, this report is based on power calculations, which are read and computed according to the available hydraulic diagram.

Dione kullager AB is a company in Uppsala, which sell industrialmachinecomponents, transmissionsolutions and provides repair serviceof hydraulic components.When a hydraulic cylinder is about tobe repaired it needs to bedisassembled. Because hydrauliccylinders usually work in dirtyenvironments and are heavilyworn some types of cylinders arealmost impossible to disassemble.Today the disassemble is made by hand,which means extra work for themechanics. In order to facilitate thedismantling of this type of cylindersa machine is to be developed for thispurpose and this is where this thesisbegins.The thesis has been organized in threephases: Literature study in whichfacts and theories are acquired.Concept generation in which differentconcepts, calculations, and solutionswere identified and selected. Thedesign phase where all the differentconcepts of components were assembledand simulated in SolidWorks. Similarstructures have also been studied inorder to identify necessary functions.The thesis resulted in a structurewhich is believed to meet therequirements.

?Optimizing the workflow of hydraulic reservoir tanks? is a degree project made by Jonas Olsson, student within the faculty of technology and science, during spring semester 2012. The project comprise 22,5 ECTS.Volvo Construction Equipment, located in Arvika, was the client in this project. The mentor at Volvo CE was A?sa Barck, and the mentor at Karlstad University was Monica Jakobsson.

This thesis aims to propose a plausible design and construction of the lost gable pediments of the Glassworks Villa in F?glavik, anno 1875. Through a combination of building inspections, photo analysis and 3D modeling, the researcher utilizes the combined results to digitally recreate the decoration that once adorned the gothic revival villa's gable, to serve as basis for its actual reconstruction. The study further highlights the use of modern technological tools, such as 3D modeling software, to further enhance the understanding of historical architectural elements. The researcher also emphasizes the challenges and considerations involved in preserving and reconstructing historical architectural details for future conservation endeavors..

In the end of the 80´s the area of system development moved into a new era. As a consequence many new methods and development models emerged which in many cases resulted in problems when choosing system development models and methods. As a result of these problems the today standardized modeling language UML (Unified Modeling Language) was created. UML is tailored to support many different types of projects. This is possible because of UML?s capacity to be adjusted and adapted to a specific company environment.The purpose of this bachelor thesis is to investigate how and why companies use UML and what experiences and opinions those who use UML have of using UML in practice.

Mathematical models possible to simulate are of great importance in order to make successful projects in the aircraft manufacturing industry. An aircraft fuel system is very complex, containing pipes, tanks, orifices, valves and pumps. The principal of this thesis is using the tool Easy5, which no longer is considered reliable enough in terms of development and support. This thesis tries to evaluate the Modelica language as a possible alternative to Easy5. To make this evaluation, the components concerned in the fuel library in Easy5 are implemented to the Modelica language.

The study was conducted in Jönköping County Chamber of fibrillation and is about change and improvement of process modeling technology. The process for treating patients with fibrillation is in the need to evolve and improve. In order to develop the care they needed a current state description which usually is made with the traditional process modeling tool.Many scientists and health professionals is in the opinion that this technology gives a too rigid image to describe the care processes. It also does not sufficiently take into account the human aspects. This reasoning suggests that the process modeling technology in healthcare is in the need to develop multiple perspectives.