Highland Group AB was helping a customer of theirs to create an All-Terrain Vehicle (ATV), a project Highland has never been involved with before. For the wishbone arms of the wheel suspension, traditional manufacturing methods and tubes with cylindrical or square shaped cross section was preferred. We performed a simulation where the ATV was driving on a bumpy road too see the forces involved. With the results we proceeded to calculate the strength of the concepts to find out which is best suited for the tough environment in which the ATV is used. The concept that turned out to be the best was a wishbone made of circular cross section, which had good structural strength and did fulfill the demands that we required for the construction.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

In a world where digital media is becoming a greater part of people?s everyday and working lives it is plausible to assume that the upcoming generation of pupils expect the teaching media to adapt thereafter. It is this assumption of an increased demand that Natur & Kultur is hoping to be able to meet. This thesis has been a stage in the process of producing digital material in the subject of mathematics for high school students. Specifically the aims of this thesis have been to make a rough description of the largest competitive companies? products within the same market, explore and put together a brief theoretical foundation of contemporary research and produce concrete examples of ideas for digital applications.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

Aim: The aim of the study was to investigate 1RM and what power could be generated in bench-press and half squat concentric at certain percentages of 1RM. Special interest was put to evaluate men (M) and women (K), strength trained (ST) verses non strength trained (EST) in generating absolute power as well as power relative to 1RM.Method: In total 59 subjects mean (± SD) age 24.9 ± 4.1 years divided into four test groups: 20 male non strength trained GIH-students (EST M), 20 female non strength trained GIH-students (EST K), 10 male strength trained - sprinters on national/regional level (ST M), 10 female strength trained - sprinters (ST K) on national/regional level. They did two tests on 1RM and power in events of concentric bench-press and half squat in a Smith machine. In the first test session 3 ? 5 lifts were made to measure 1RM in each event.

This thesis has examined the Tekla Structures modeling software and answered the question of whether it could act as a suitable modeling program for the design department at Bjerking AB in Uppsala. The method used in this work is a case study of a previous project with existing basis to work form. The demarcation of the study was to examine only the usability of the foundations of in situ concrete. The work examined three main areas within the design process. The first was to model the concrete elements then to model the reinforcing and ultimately production of the drawings. Because Autodesk Revit was the existing modeling program in the Department conducted the evaluation as a comparison between the two programs.

To identify the exchange and adaptation that takes place in the business relationship between electricity suppliers and electricity customers and analyze how these factors affect the strength of the relationship.The investigated concepts create synergies. The strength of the business relationship in the current situation is dominated by weak reciprocity in adaptation and an inefficient exchange of information with low frequency..

Publicity is argued to have relatively great impact on attitudes and behaviours of consumer. Especially great is the influence of negative information. At the same time it is likely for brands to be subject to negative publicity. Since companies are investing gigantic sums into buidling strong and positive associations around their brands it is of great economic interest to have a better understanding how negative publicity influence brand equity and what factors might moderate this effect. This thesis focuses on brand strength as a moderating factor of negative publicity.

Publicity is argued to have relatively great impact on attitudes and behaviours of consumer. Especially great is the influence of negative information. At the same time it is likely for brands to be subject to negative publicity. Since companies are investing gigantic sums into buidling strong and positive associations around their brands it is of great economic interest to have a better understanding how negative publicity influence brand equity and what factors might moderate this effect. This thesis focuses on brand strength as a moderating factor of negative publicity.

This report will try to evaluate the use of rented concrete casting moulds, which are used to build walls and system of joists. The evaluation is only examining the economical aspects.The cost of using concrete casting moulds is a big part of the total production expenses. Therefore it is important that the calculated price not exceeds the final costs of the casting moulds. The calculated price is the price used in the process of making an offer.The evaluation consists of a comparison of the calculated price and the final costs for three building projects. It also evaluates the exploitation of the concrete casting moulds for each project.The report is made by Sven Gynne and Anders Alexandersson at School of Engineering, Jonkoping University, in cooperation with PEAB Jonkoping.

In this diploma work the approach of determining the required amount of reinforcement in slabs exposed to pure tension is processed, on behalf of Ramböll Uppsala. It is a well-known problem in the industry that there are uncertainties in the determining of the amount of crack reinforcement, especially for structures exposed to pure tension. Cracking caused during the time of dehydration in concrete slabs is the most common defect according to statistics made by CBI[1], which provides numbers as high as 35 % of all the defects caused on slabs are generated by cracks. Comparisons between Sweden's former national standard BBK 04, Building Regulations for concrete structures due to restrained forces of shrinkage, and the current European standard Eurocode 2 are carried out through theoretical studies and concludes with several examples of calculations. Rigorous calculations of both standards, BBK 04 and Eurocode 2 with application of the national annex in Sweden and Denmark are performed.

Wooden joist slabs is a common type of floor in residential buildings. Higher demand and production of residential buildings increases the possibilities of profiting by optimizing the system of joists in a variety of areas. Spring and deflection is something most people can relate to since it?s not that uncommon to hear furniture rattle when you walk over a wooden floor. To remove the presence of those kinds of vibrations the system of joists have to be made stiffer than the standard joist construction that is used in today?s constructions.

This essay examines the indirect effects of the local strength of the Swedish Democrats on refugee acceptance in the Swedish municipalities. With statistical methods this essay has aimed to investigate if such effects exist and by using statistical data from three periods of time - 2002, 2006 and 2010 ? the investigation has been able to measure effects over time. Based on former research and reasonable expectations the hypothesis for the essay claims that the Swedish Democrats has got an indirect effect upon the refugee acceptance. With the statistical analyses made, the essay is able to conclude that the strength of the Swedish Democrats in municipality elections as well as the change of this strength between the elections does have a negative effect upon refugee acceptance in the Swedish municipalities.

In this diploma work the approach of determining the required amount of reinforcement in slabs exposed to pure tension is processed, on behalf of Ramböll Uppsala. It is a well-known problem in the industry that there are uncertainties in the determining of the amount of crack reinforcement, especially for structures exposed to pure tension. Cracking caused during the time of dehydration in concrete slabs is the most common defect according to statistics made by CBI[1], which provides numbers as high as 35 % of all the defects caused on slabs are generated by cracks. Comparisons between Sweden's former national standard BBK 04, Building Regulations for concrete structures due to restrained forces of shrinkage, and the current European standard Eurocode 2 are carried out through theoretical studies and concludes with several examples of calculations. Rigorous calculations of both standards, BBK 04 and Eurocode 2 with application of the national annex in Sweden and Denmark are performed.

The incidence of damage to the claws and legs in piglets caused by the floor in farrowing pens is a widely known problem and very common in today's pig herds. Although the association between floor and damage has been known for over 35 years, no suitable solution has been found to reduce the negative impact. The purpose of this study was to make a literature study to document the experiences of the use of different types of flooring in farrowing pens and also, in an own study, examine if soft floor in farrowing crates could lead to reduced damage to the claws and legs in piglets compared to concrete floor. The study was conducted in two herds, A and B. In each herd, farrowing pens with concrete floor and concrete floor with polyurethane coating were compared.