Cost allocation ? a study of how Swedish energy companies allocate costs between electricity and district heating in a combined heat and power plant District heating is today the most utilized alternative for heating in Sweden. In a combined heat and power plant (CHP) electricity and heat are cogenerated. The environmental and economic advantages with this kind of production are high. A problem in a CHP-plant is to allocate costs between electricity and heat since both products are generated in the same process.

Poly- and perfluoroalkyl substances (PFASs) are a group of environmental contaminants that have gained increasing attention due to their potential to bioaccumulate, environmental persistence and potential toxicity. PFASs have been found in surface water, sediment, air, soil, sludge and ice caps globally, as well as in wildlife and humans. Furthermore, PFASs have also been detected in drinking water, leading to raised concerns for human health, since drinking water is one of the most significant sources of PFASs for the general population. Conventional water treatment techniques have shown to be ineffective removing PFASs, highlighting the importance for further research to develop efficient removal techniques. The aim of this study was to investigate the removal efficiency of PFASs in water using two treatment techniques; granular activated carbon (GAC), type Filtrasorb 400®, and anion exchange (AE), type Purolite A-600. Additionally, the effect of dissolved organic carbon (DOC) on removal efficiency was studied.

A new build in the Swedish nuclear power system would entail increased re-quirements for the proposed repository, which is adapted after the reactors of today. With a fast reactor, capable of burning nuclear waste, operating in parallel with the light water reactors, the increased requirements on the repository could be reduced.In this thesis, simulations of a light water reactor and a fast reactor have been performed by using the Monte Carlo code Serpent to investigate the changes in the fuel inventory. The light water reactor in the study is a boiling water reactor and the fast reactor of the type sodium-cooled fast reactor and they have been used for three different operation scenarios.By studying the fuel composition and the results from the simulations of the three scenarios conclusions can be drawn. Conclusions regarding the change of the fuel inventory and decay heat in Clab as well as the interim storage facility and in the repository. Depending on the operation alternative the changes dif-fered significantly and especially regarding the mass of burned actinides for different fuels in the fast reactor.The lowest increase of fuel assemblies was meet when using 50 years old fuel with 20MWd/kg U burnout and 2,0 % enrichment for start up of the fast reactor and 30 years old fuel assemblies with 50MWd/kg U burnout and 4,7 % enrichment for the further operation of the reactor.The increase of the number of fuel assemblies was 3174, which is equivalent to 641tons of heavy metal.

The aim of this study is to find a method to incorporate the energydemand of a building in the investment cost estimate.The study is based on an actual apartment block. The significant energyaspects are identified, and changed to more energy efficient options.These are then simulated using the energy calculation program VIP+.The calculated energy need is used in the investment cost estimate, andthe simulated alternatives are compared in regards to their economicalprofitability.Depending on the focus, different alternatives are the most advantageous.Since this study aims to show which alternative is the mosteconomically profitable, the annual profit is the parameter of mostimportance. This means that individual measuring of heating and hotwater use is the recommended change of the original house. A changeof the windows to new ones with a U-value of 1,0 as well as 0,8W/m2K also results in a positive change of the annual profit comparedto the original house..

Stage-discharge equations for lakes without disharge measurementsSimon AnderssonIn 2015 all lakes, rivers, coastal water and groundwater should be of good ecological statusaccording to the water framework directive from the European Union. In the process ofimproving the quality of Swedish water bodies, knowledge of where problems occur isneeded in order to utilize the resources optimally. The ability of lakes to store water is animportant factor since it controls the flow of water through the country. A stage-dischargeequation is a mathematical relation between discharge from a lake and its water level. Bybetter understanding of stage-discharge equations for lakes, their storage capacity can bedescribed better in hydrological models.This master thesis aims to evaluate methods for determining stage-discharge equations forlakes where a variable amount of field measurements is available.

This report investigates a possible solution to the problem with adapting wave powerplants to work in countries with tidal water. The wire connecting the buoy at the surface with the generator at the bottom needs to adjust to the varying water depth. Our solution to this problem is to attach the wire to a jack which is then placed inside the buoy. The jack is then powered by an electric engine. The report discuss what forces the buoy will be exposed to and then the structural integrity of the design is evaluated through simulations.

Uvån Hagfors Teknologi AB (UHT) has developed a process ? GRANSHOT® ? for quicksolidification of metals in water baths. In the process liquid metal is splintered ? granulated ?into small drops. The drops are rapidly cooled in a water bath where all the heat energy from theliquid metal is transferred into the water.

If a building is heated by a heat pump, it is of high importance that the heat pump has a high coefficient of performance. An exhaust air heat pump extracts heat from the building?s exhaust air. The air has a relatively high and constant temperature all year around, leading to a high seasonal coefficient of performance. This thesis examines whether it is profitable to complement an exhaust ventilation system with an exhaust air heat pump in an apartment block that already has geothermal heat pump, district heating, oil- or biofuel heated system.

Hemp has been used for textiles for a long time in history until it became illegal to grow in many countries in the 1930s. It is interesting from an environmental point of view because it doesn?t need any pesticides and in most locations it doesn?t need any irrigation either, compared to cotton, which normally requires big amounts of both pesticides and water for irrigation. Hemp is a bast fiber, which means that the fibers are located on the bast of the stem (on the outer layer of the stem). Therefore they cannot be spun directly, they have to be removed from the stem first.

Most of the saw and pulp industries have stored wood nearby their production, the main reason is to have a continuous wood flow to the production. Wet storage of wood is of great importance to keep the wood quality. Without water sprinkling the risk of drying outand decomposition through biological activity increases significantly and will result in a negative effect on future production and quality. One drawback of wet storage of wood is the leaching of chemical substances into the surrounding recipient. The log yard run-off contains phosphorus, nitrogen, phenols and organic substances. These substances can cause problems for the surrounding environment. The main objective of this project is to gain an understanding of the wet storage used by the Swedish wood industry and estimate the environmental consequences that run-off water will have on the recipient.

Buffer zones play an important role for the water quality in our watercourses. When harvesting a forest close to a watercourse a buffer zone should be left. When it's not left, it will lead to radical changes in the environment for the water organisms. The overall purpose of this thesis was to illuminate the production- and environmental thinking when establishing new buffer zones in south of Värmland. The partials goals were to determine choice of tree species, ways of regenerate, occurrence of soil scarification and the occurrence of machine tracks in newly established buffer zones.

Arlanda airport is Sweden?s largest airport. The demand for comfort cooling of the airport?s buildings is high and is mainly provided by district cooling. District cooling is based on the same principle as district heating.

In order to reach the environmental targets, set up by the EU, there are many measures taken to make Sweden more energy efficient. In the housing and real estate sector, an installation of an exhaust air heat pump that reuses the heat in the exhaust air in order to lower the amount of acquired energy, is an example of such an action. The recovered energy can then be used for heating of radiators and tap water. This report aims to evaluate and compare three different systems using exhaust air heat pumps regarding COP, degree of coverage and cost savings. This study was delimited to only account for apartment buildings.The theory chapter describes the different conditions and factors that affect a building?s energy balance.

In the process of making carton boards into Skoghall Mill, are great quantities of water being contaminated. This water has to be treated before it is possible to release into the recipient, Kattfjorden. One of the contaminations that is important to extract from the wastewater, is organic carbon (measured as TOC-total organic carbon) because microbiological breakdown can lead to the bottom becomig free of oxygen.The wastewater treatment at Skoghall Mill is done through an external wastewater treatment that is located at the factory. The biological treatment (aerated lagoon) is a 140 000 m3 water pool with surface aerator, which is give oxygen to the water. In the lagoon live microorganisms who performs the biggest part of the TOC-reduction.One problem with the lagoon is that the treatment of TOC is considerably worse during wintertime than during summertime.

Latent heat storage is a way to store thermal energy when a phase change material undergoes a phase change. The advantage of latent heat storage is the capability to store more energy per mass unit than other heat storage methods. The most commonly used phase change in latent heat storage is the transition between solid and liquid. Phase change materials can be divided into organics, inorganics and eutectics.In the Nordic electricity market the price of electricity is set every hour by Nordpool spot, which leads to price fluctuations because of changes in demand. The main goal of this report is to create a latent heat storage system in a single-family home and investigate the possibility to save money by charging the latent heat storage system when the price of electricity is low, and discharge when the price is high.The thermodynamic model consisted of a ?tube-in-tube? heat exchanger with phase change material in the outer tube and water as the heat transfer fluid in the inner tube.