AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

People in today?s society are becoming more and more aware of how important it is to use energy as efficiently as possible. This is clearly noticeable by an increase in home produced heat with e.g. solar panels or heat pumps Heating systems. These changing customer demands forces district heating technology to be redesigned, which is why there is an ongoing research regarding the next generation of district heating - low temperature district heating (LTDH).

In order to facilitate testing of anesthesia machines a patient simulator has been required by Maquet Critical Care AB. A patient simulator has been developed to reduce expensive and time consuming animal experiments and temporary lab arrangements. The patient simulator has been developed and designed to simulate human lungs with regards to anesthetic uptake, production of carbon dioxide and heating and moisturizing exhaled air.The system comprises a container and a test lung to simulate the volume and the dynamic of the human lung. The simulation of uptake of anesthetics has been implemented by pumping a fraction of the gas from the container through a bypass circuit with an active charcoal filter that adsorbs volatile anesthetics. The flow through the bypass circuit is generated by a pump and is controlled by a linear valve.The resulting performance of the patient simulator has fulfilled the requirements.

Aeroseum is an aviation museum located in an old military underground hangar. The ventilation system in the hangar is designed for the military purpose of the hangar. This design includes a solution with air flowing through the space between the construction of the hangar and the rock surface. The solution is intended to avoid a buildup of inflammable gases. This design leads too high humidity levels in the hangar.

The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.

AbstractThis thesis examines and discusses a sample of the medieval hypocausts (stone-heating ovens) in the Baltic area. The medieval construction is thoroughly explained as well as the antique hypocaust in order to establish a base for the following discussion. The medieval hypocaust has been almost forgotten for a long period of time. The last time someone dealt with this category of finds were in the 1960?s by Swedish archaeologist Iwar Andersson and in the 1970?s by Danish archaeologist Johannes Hertz.

An increased awareness about the global warming has created a demand for more information on how the climate is affected by different activities.This master thesis was initiated by Tricorona, a Swedish company that offers its customers analysis and calculation of their climate impact. Tricorona also supplies climate neutralisation with CERs, in accordance with the Kyoto protocol and controlled by the UN. This work demands updated emission factors for greenhouse gases. An emission factor gives information about the greenhouse gasintensity of a service or a product [kg CO2-eq./ functional unit].The purpose of this thesis is to examine how electricity, district heating, hotels, taxis, food and materials affect the climate and how emission factors for these areas can be calculated.This was done by reviewing and comparing different studies and by interviewing experts. The information was evaluated and recommendations on calculations and emission factors were made.The consumption of energy is the main source of greenhouse gas emissions for district heating, electricity, hotels, taxis and materials.

In today?s society a large focus is put on energy systems and how our energy systems are built up. In order to make sure that we in the future still can enjoy the living standards that we are used to today, Sweden and EU have made a number of decisions on making our energy system more energy efficient and consequently reduce the usage of energy resources. By 2020 the European Union should have reduced its energy consumption by 20 % compared to 1990?s level, and by 2050, 50%.

In order to reach the environmental targets, set up by the EU, there are many measures taken to make Sweden more energy efficient. In the housing and real estate sector, an installation of an exhaust air heat pump that reuses the heat in the exhaust air in order to lower the amount of acquired energy, is an example of such an action. The recovered energy can then be used for heating of radiators and tap water. This report aims to evaluate and compare three different systems using exhaust air heat pumps regarding COP, degree of coverage and cost savings. This study was delimited to only account for apartment buildings.The theory chapter describes the different conditions and factors that affect a building?s energy balance.

Stump wood is a hot alternative when the heating plants demands more and more forest fuel. The aim with the study has bean to calculate the costs in four different systems for transportations of stump wood, examine if there are any differences in fuel quality for the stump wood in the different systems, analyse if the fuel quality in stump wood is affected with the time it lays by the road side and how much space the stump wood demands on the road side. To calculate the costs for the different systems a system analysis was carried out, where some of the costs were collected through field studies on Holmen Skog stump experiment and other costs were collected from literature and contacts. Data for the fuel quality study was collected from Eons heat plant in Norrköping. Data for the study of how much space stump wood takes along a roadside was collected from field studies.

Sweden has distinct seasons with cold winter and temperatures down to minus 25 ?C andpleasant summers with temperatures above 20 ?C. During spring and autumn there could becomechallenges with precipitation. The diverse climate in Sweden affects many homeowners. For thepeople living in leisure boats and permanent housing boats the seasonal changes are clearlyimpacting their economy and the indoor climate.

Biogas is a renewable fuel that can be extracted from anaerobic digestion of many differentsubstrates, for example biological household waste. An alternative handling of the waste is tomix it with other wastes and incinerate it in a combined heat and power (CHP) plant. Thisstudy uses life cycle assessment to investigate which type of waste handling that is betterfrom an environmental point of view, anaerobic digestion with biogas production orincineration. The results are based on a case study of a biogas production plant owned by thecompany Ragn-Sells in Vänersborg. The alternative is incineration at a CHP plant inGothenburg.

Wavecraft AB develops medical equipment for heating of organic synthesises. The heating is done with microwaves, which improves the process in both speed and accuracy compared to the more traditional methods where heating elements are used. This report discusses the developement of an automatic lid mechanism for one of Wavecraft's product prototypes. The company assumes that the final product will be integrated by customers into fully automated systems, and the upgrade from a manually to an automatically controlled lid is therefore an important step in the product's developement process.The first stage och the project was an idea generation process. The ideas generated here were organized into five different concepts of which the best one was selected through the use of a concept matrix.

The sun is a huge energy source with great potential of providing energy to the heating of homes and other buildings in an environmentally sustainable manner. In order to provide buildings with energy from the sun it is necessary to transfer the energy supply over time to when the demand arises. By storing the heat in a seasonal storage, solar energy from the summer can be used in the winter when the demand for heating is greatest.Today's existing plants are mainly in Europe and particularly in Germany. These facilities are designed to supply heat demands greater than 400 MWh and covers about 40-50 % of this need which consists of energy for space heating and domestic hot water. How much of the heat demand that is covered, the solar fraction, is partly due to losses from the storage which in turn is connected to the surface area of the storage.

After been told that an ordinary winter service for our combine should cost more than 20000 SEK, not included spare parts, I decided to write this paper about today?s requirement of the workshop on a farm. I think that the lack of proper premises is the reason way not more of the ordinary machinery maintenance or upkeep is performed on the farm. When I did my literature survey I found that the Swedish environmental code, set by the Swedish law regulate how drain or sewer should be built. The environmental code however leaves a lot for your own interpretation. It might not be so bad but it must be very hard for the local environmental office to interpretation the regulations, since they are the ones that gives permission for the sewer in your workshop.