The purpose of this study has been to evaluate whether a Low temperature bio-mass dryer could be integrated with the local district Heating system in Malå. The aim is to increase the thermal efficiency of the cogeneration plant in Malå, by lowering the temperature of the cooling medium. Another benefit that comes from this is improved combustion efficiency at the power plant, since drying the fuel causes an Increase of the heating value.Simulations has been made in Excel, and with use of linear regression, to find out if it is profitable. Data for this purpose has been supplied by the power company Skellefteåkraft and furthermore SMHI.The result of the Calculations shows that a very efficient bio-mass dryer is needed, if yield of investments should be made possible. An Investment of 4,27 Mkr, in a dryer, could at a such criterium return 60000 kr/year, if the price of the biomass is 190kr/MWh.

This diploma work covers an investigation over the heat - and hot water systems of thetenant-owner's association, Bogården. The heat - and hot water needs of Bogården aresatisfied by both district heating as well as three heat pumps. Implemented investigationshows that the heat pumps are not used in a profitable way. Apart from that, the reservepossibilities are small. There is also a risk of the growth of Legionella bacterium in thehot water system.Since the heat pumps are already installed, HSB-Gävleborg (responsible for Bogården)has a wish to investigate possible proposed actions for optimization of existing plant.After completed investigation, a new proposed action is presented.

This thesis provides a good introduction to the American environmental certification system LEED, Leadership in Energy and Environmental Design, and trough compar-isons between Sweden and the United States an explanation to the systems design is given. The work is closely linked to a LEED Core & Shell project in Stockholm, Swe-den, where the goal is to reach the second highest rating in LEED - Gold.This thesis gives a broad description of the LEED system and a more profound study of the energy sector, Energy and Atmosphere. Here, for example, an analysis has been made of how the energy consumption of an imaginary building designed according to the requirements of the BBR (Swedish building code) performs in comparison to the Baseline building in LEED.The existing model of Borgarfjord 3, which served as a case study in this work, has al-so been modified to investigate the energy savings that could have been achieved by adding extra insulation to the building. A description of the problems, regarding how the Swedish district Heating system (DES) is treated in LEED, is given as well as the suggested modifications. This is an issue that will be pursued during the process of shaping a new, international, version of LEED due to be launched 2012..

A possible way to reduce pollution and slow down the process of global warming is to increase the usage of renewable energy sources. One of these renewable energy sources is solar power. With the aid of solar panels and solar cells the energy from the sun can be transformed into both heating and electricity. The requirement to use the sun in this fashion is a suitable surface, for example a big roof, an angle between 40-60 degrees and that the surface should be exposed to the south. Almost every farm meets these requirements.

This Master degree project has been performed at the Braviken paper mill on papermachine 53 (PM53) which produces newsprint paper. The current economic situationhas contributed to declining demand for newsprint, which means it is extra important tobe competitive by high energy efficiency. Particularly as energy prices are expected torise when the economic growth returns.One way to increase energy efficiency is by reducing the water use in paper and pulpmills and consequently save energy through reduced heating of water. The thesis's maintask is to evaluate whether a water purification plant (microflotation plant) forpurification of process water in PM 53 is profitable. The microflotation plant enablesreuse of warm process water instead of losing the energy to receiving waters.

The thesis aims to compare differentpiping materials in Heating systems interms of cost as well as to illustratethe impact of energy characteristics ofdifferent materials over its servicelife. The methods used for costcalculations regarding piping are alsoto be examined to highlight thedifferences between template basedcalculations and more carefully executedones. The work is delimited to discusspipes of steel, copper, plastics andcomposites. The aim is that the resultcan be compiled to illustrate the prosand cons of various materials whenevaluating investments.The main object of the survey is part ofa Heating system in the office-block KVSommaren located in southern Stockholm.The configured piping system is designedwith the mentioned piping materials andis used to make up the data for flow andcost calculations. The differentmaterials are calculated in both aconventional manner with a supplementarycost for additional fittings and with amore accurate quantification of thecomponents.

An energy calculation model for Swedish houses   that is fast, flexible and user-friendly has been developed within the   framework of this thesis.  The model   also provides a set of actions which may be investigated in the model based   on savings and payback period. Energy use in a house depends on the technical   conditions, such as building envelope and Heating systems, which outdoor   climate the house is exposed to and who lives in the house. Energy use for a   house can be divided into heating, hot water and household electricity. There   are several methods to calculate the energy use of a house. This report   summarizes the methods that may be suitable for a fast and user-friendly   calculation model.

SAPA´s resource of waste heat is the basis for this thesis to investigate the possibility of energy assets in their cooling water and possible uses for it. The energy in the waste water is greater than the current need which has three uses which are (1) heating the factory, (2) converting liquid propane to propane gas and (3) local domestic heating. The average energy load that is available is 1, 7 MW and the average temperature in the cooling water is 41°C. The total energy load at dimensioning out side temperature is approximately 1,6 MW for the three current uses. The temperature is currently too low to be used directly in the existing systems so an upgrade is needed.

An increased awareness about the global warming has created a demand for more information on how the climate is affected by different activities.This master thesis was initiated by Tricorona, a Swedish company that offers its customers analysis and calculation of their climate impact. Tricorona also supplies climate neutralisation with CERs, in accordance with the Kyoto protocol and controlled by the UN. This work demands updated emission factors for greenhouse gases. An emission factor gives information about the greenhouse gasintensity of a service or a product [kg CO2-eq./ functional unit].The purpose of this thesis is to examine how electricity, district heating, hotels, taxis, food and materials affect the climate and how emission factors for these areas can be calculated.This was done by reviewing and comparing different studies and by interviewing experts. The information was evaluated and recommendations on calculations and emission factors were made.The consumption of energy is the main source of greenhouse gas emissions for district heating, electricity, hotels, taxis and materials.

AbstractThe Municipality Council decided in 2010 to develop a comprehensive energy efficiency strategy with financial and methodological support from Energimyndigheten (The Swedish Energy Agency). The strategy should include 3 major parts: an inventory of the 2009 energy use defining the current situation, the 2014 and 2020 goals for energy use, and an action plan for goal achievements. According to Energimyndigheten, the strategy must include all municipal administration premises, vehicles, and all majority-owned companies (as Laholmshem, the municipal housing company).The report describes the inventory work in order to obtain the 2009 energy use and the sources of information used. The inventory values are used as the base year values for the 2014 and 2020 goals. The inventory showed that information about the vehicles is dispersed in the municipal administration and no clear structure exists with respect to mileage and fuels used.

In June 2006 the Swedish government decided that the use of energy in buildings should be reduced by 20 percent until 2020, compared to the level of energy used in 1995. To contribute to this goal, the real estate company ?Eskilstuna Kommunfastigheter AB?, set up own goals for their buildings. In 2009, the goal for schools was to have a maximum energy use of 118 kWh/m2year for heating and hot water.The school ?Hållsta skola?, just south of Eskilstuna, exceeds the limit since it used 270 kWh in 2008.

Wavecraft AB develops medical equipment for heating of organic synthesises. The heating is done with microwaves, which improves the process in both speed and accuracy compared to the more traditional methods where heating elements are used. This report discusses the developement of an automatic lid mechanism for one of Wavecraft's product prototypes. The company assumes that the final product will be integrated by customers into fully automated systems, and the upgrade from a manually to an automatically controlled lid is therefore an important step in the product's developement process.The first stage och the project was an idea generation process. The ideas generated here were organized into five different concepts of which the best one was selected through the use of a concept matrix.

The building sector accounted for around a fourth of the total energy usage in Sweden in year 2010 (Energimyndigheten, 2012). Therefore it has become very interesting to achieve a lower energy usage in residential buildings. One way to achieve that is to build so called passive houses. By being very well insulated and have low leakage through the walls, they can reduce the energy usage for heating with a substantial amount. The first passive house was built during the 90?s in Germany; and in Sweden the first passive house was built in Gothenburg 2001.

AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

This thesis has been written with our society?s current energy-situation in mind.Although it only deals with one particular block of buildings, the solutions and suggestions presented herein are quite applicable on other objects of the same type.This thesis is intended to be used as a guideline for energy-preserving projects in general, with an eye to buildings erected during the Swedish ?million-programme? in the sixties and seventies.The paper starts with the acquiring of all necessary blueprints and technical specifications. It then moves on to a thorough description of the buildings in question, and their heating- and ventilation-systems.Followed by this the reader is guided through the successive stages of energy-perseverance measures that are available, and possible. Reasoning around the economic factors concerning all measures is also held.The paper ends with conclusion, and a discussion concerning the delicate issue of the higher return-temperatures possibly reaching the district-heating plant..