The industrial sector accounts for a large share of greenhouse gas emissions. To reduce its negative impact on the environment is crucial in the quest for a sustainable future. In discussions of the industrial sector's impact on the environment guidelines have been highlighted as a tool to assist the industries in their efforts to change the relationship between the consumption of energy and production. This by improving energy efficiency and a shift to the best available technology. During the past 30 years the steel industry has reduced its energy consumption per ton of steel produced by 50 percent.

The purpose with this essay was to examine how the European Union is working totransfer norms to states they signed an agreement with and provide support for inframe of the Barcelona process and the Tacis programme. The theory which weused was Ian Manners (PhD in Political Science) theory of "the EU as a uniquenormative power". The aim was to examine whether the EU - which Manners mean- has had a normative power to influence states to change. We used a qualitativeapproach through the use of a multiple case study and qualitative text and contentanalysis. The States which formed the basis of our study were within the BarcelonaProcess; Morocco and Tunisia as well as Azerbaijan and Armenia funded by theTacis programme.

We are heading towards a huge switch of how energy is produced with fossil fuels being replaced by renewable energy sources. It is not difficult to replace the energy you use in the house and there is no need for futuristic technology. There are already many established products on the market such as high efficiency vacuum solar collectors, heat pumps & small wind power stations that can supply the energy being used in a house. The company Sol & Energiteknik SE AB in Huskvarna has many different products which can reduce the need for an outside energy distributor. An average house in Sweden uses 15 000 kWh for heating, 5000 kWh for tap water and 5000 kWh for electricity.

AbstractElectricity consumption is a globally increasing problem caused by the high share of electricity produced in coal power plants. These contribute to high carbon emissions when only about 1/3 of the heat generate electricity and the remaining 2/3 of the heat cools off. Combined heat and power plants (CHP) have high efficiency because they use the residual heat for domestic heating. The CHP plant often use fuels from renewable resources, giving them a lower carbon footprint, but are also depending on the heat demand. If electric powered products such as drying cabinets convert to heat powered products more environmentally friendly electricity will be produced by CHP plants, which can supplant electricity, produced from coal power plants and reduce carbon emissions.

The municipality, of Gatukontoret in Local government of Borås has in the long run, a required need to look after the current heating devices (the gas production plant) in sewage treatment plant, called Gässlösa. The practical work of the examination is about, trying to find a better way to take care of the current heat recovery. That may be one way or another, rather easy to implement in the existent construction.Through the work to increase the efficiency of the gas engine, implement of some external cooling system by heating exchange device. That gives an opportunity to heat (primary) the digester, (but even all internal public areas) with its own superfluous heating.The report shows that if the management group may invest 422 704 crown to implement a heat exchanging device, it gives more space to reduce the need to buy expensive external energy. Gatukontoret´s pay off time, for buying machines, is 20 years, with reservation to calculate with 4 percent internal interest, leads to the yearly mount of 31103 crowns.If Gässlösa increases the gas engine time in (effective) duty approximately (correspondingly) 48 hours a month the entire investment will generate a profit in January in year seven after the implementations.

Stockholms vattenskärning AB in Kungsängen has through the acquisition of a company begun to design and produce aircraft heaters whose origin is early 1970s which follows a high inefficiency in terms of energy consumption and size.The aircraft heater, which is sold worldwide, serves its purpose for customer satisfaction and has done so ever since it was developed in the 70s.Stockholms vattenskärning AB is now investigating the possibility in making the aircraft heaters more efficient, both in terms of energy consumption but also on a more efficient design with the belief that it would lead them to an edge in the market. The aircraft heater consists of several main components whose function altogether is to keep passenger aircrafts warm while they are on the ground.This project has been limited to the further development of the heat exchanger package which accounts for the conversion of the hot medium to the fresh air being carried in to the aircraft cabin. Work has been divided into different phases in order to create a better understanding of the project range and to make it easier to divide the various elements in the time available, 10 weeks. These phases are literature review, situation analysis, concept generation, CAD, concept comparison and writing reports.After the initial literature review was made, a fundamental theory was written which is essential in understanding the remaining parts of the project.With the theoretical part as support, measurements and calculations were made on the current heat exchange package in a situation analysis to ensure its operation and efficiency.In the concept generation phase, the collected facts from the literature review was used as the basis for creating a matrix. The purpose of the matrix was to indicate the two most suitable types of heat exchangers to develop four new concepts out of.In the CAD phase the four concepts was drawn up and then described with text and images.The last phase is the concept comparison where a concept selection matrix is used to function as a decision basis for further production at Stockholms vattenskärning AB. The four concepts have been developed based on the current heat exchanger and is gradually changed into a design of a cross-flow heat exchanger constructed out of stainless sections. The purpose of this is to have gradual upgrading of the heat exchanger as an option, in order not to saturate the market..

A Swedish electronics company wants to make the cooling of one of their electronic components more efficient. They propose that a retrofit liquid cooler is the way to achieve this goal. The current air cooling has high energy cost due to the high amount of power needed to power fans and heat exchangers. Using high volumes of air for cooling also leads to noise pollution. The conversion from air to liquid cooling would possibly make the operation of the electronics more cost efficient and less noisy.The purpose of this project is to theoretically evaluate different concepts of drawing the heat generated by the electronic component in to a fluid, using numerical calculations in Matlab and FEM simulations in ANSYS.

This report treats whether it is viable to invest in solar heating to heat the therapy pool at Östersunds Rehabcentrum. The rehab center is owned by the county council of Jämtland and is located on Solliden in Östersund city. The solar heating where supposed to be a complement to the district heating that was heating the pool in the current situation. Later, it however showed that this was not the case. The pool is currently being heated by a radiator circuit that is being heated by the district heating.

In cooperate with Asko Cylinda we have developed a new heat system too short the process time and reduce the energy consume in a dishwasher and still have it too be a class AAA. The environment and quality is important for the company too still be the number one on the market, If they want too keep that position the product developed of new innovations will be very important. The systems we have developed are more effective and reduce energy up too 25 %. The process time is reduced too less than two hours, from the today two and half-hour. The solutions are too heat up the rinse water and the dishwater at the same time, with a new heating system and it make are solutions unique and effective. Its good for the dish and the environment.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.

Swedish family companies are facing a tremendous change in the form of generation changes because of the large part of owners that are about to retire. If all 45 000 to 50 000 family companies ceases to exist, Sweden looses a significant part of business trade.There are numbers of different methods for an older generation of owners to transfer their companies to a younger generation such as inheritance, gift, will, internal stock transfer, division?s etc., where inheritance is the most complex area. That an owner of a company dies without any plan for the future of the company is not preferable because the rules of legal successions occur. The law system regarding inheritance is usually not a good method since the surviving wife, who has the primary right to the inheritance, may not be interested in the company.

According to a decision of the European Commission, measures are to be taken to reduce the use of energy in the EU. The goal is to reduce it by 20 % compared to the current use. This shall be done to the year 2020 (European Commission, 2011). One industry that use large amounts of energy is the construction of buildings which account for almost a third of the energy use (Brogren, 2012). The major part of the energy that is used in the construction industry is not used when the buildings are built, but rather during the rest of their subsequent lifetime.

Clostridium difficile is a pathogen for both humans and animals and is often associated with antibiotic-associated diarrhea. Recently, several human cases of C. difficile-infection with increased mortality and morbidity have been reported. In studies performed in different countries C. difficile has been found in meat.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.

This report was performed in order to evaluate a new technological measure and focuses generally on a heat pump system to a HWC-washing machine. The client is Asko Appliances AB, a company well known for its environmentally friendly products. The goal of this study was to improve the energy efficiency of a washing machine by combining a heat pump device to the heater of the wash water, in order to reduce the energy consumed for heating the water. Besides reducing the energy consumption in heating the water, the washing machine was required to meet low noise and short operating time specifications. For that purpose, nine trials in three test series have been carried out.