Finnhamn is a group of islands that are located in the middle north part of Stockholm?s archipelagos. On the main island Stora Jolpan there is a camp called Sommargården, which consists of eleven different buildings in various sizes. The assignment given by the Archipelago foundation (Skärgårdsstiftelsen) is to analyze if it?s benefited to replace Sommargårdens current heating system that consists of electricity radiators, with a more energy efficient heating system. This research is done with help of the literature review and a visit to Finnhamn in order to map Sommargården?s current state and its energy usage.

This thesis aims at determining the heat losses in a property vent stack and its roof valve. Upon request of a company, the vent stack is analysed for possible heat recovering solutions to be implemented, while relining of the drain system is executed and with a suitable payback time for the economic investments. The heat loss calculations are based on data for properties that are located in the Stockholm region, but also easy to change depending on the situation. The calculations are done on pipes made out of cast iron, which still is the most common type of drain pipe in Sweden, and these are the pipes that relining is usually made on. The calculations that needed to take several variables into account have been done in MatlabR2014a and the thermos dynamical properties that were used in those calculations have been extracted from EES.Three different types of heat losses in the vent stack have been taken into consideration in this thesis.

In June 2006 the Swedish government decided that the use of energy in buildings should be reduced by 20 percent until 2020, compared to the level of energy used in 1995. To contribute to this goal, the real estate company ?Eskilstuna Kommunfastigheter AB?, set up own goals for their buildings. In 2009, the goal for schools was to have a maximum energy use of 118 kWh/m2year for heating and hot water.The school ?Hållsta skola?, just south of Eskilstuna, exceeds the limit since it used 270 kWh in 2008.

Syfte och frågeställningarStudiens syfte är att ta reda på ifall det är förenligt med lagen att använda sig av artistskatt (A-SINK) på signing bonus trots att spelaren i fråga tänker stanna i landet i mer än sex månader. Vi vill också utreda om det i så fall är möjligt att betala ut en stor signing bonus till spelaren istället för högre lön. Våra frågeställningar blir således:Kan man tillämpa artistskatt på signing bonus när en spelare går från en utländsk till en svensk klubb?Är det möjligt för klubbarna att betala ut en stor signing bonus och inte betala ut lön?MetodVi har baserat uppsatsen på kvalitativa intervjuer samt studier av lagtext, förarbeten, rättsfall och relevant litteratur. Intervjuerna är genomförda med låg grad av strukturering och standardisering.

Cost allocation ? a study of how Swedish energy companies allocate costs between electricity and district heating in a combined heat and power plant District heating is today the most utilized alternative for heating in Sweden. In a combined heat and power plant (CHP) electricity and heat are cogenerated. The environmental and economic advantages with this kind of production are high. A problem in a CHP-plant is to allocate costs between electricity and heat since both products are generated in the same process.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

The main purpose of this project was to make a survey of the steam and electricity consumption at Akzo Nobel Functional Chemistry AB and give suggestions of how to minimize them. These three different areas were focused on. First to make a survey of all the most important consumers, second to find the electricity consumption of the air compressors and the amount of waste heat produced from them. The third area was to calculate a model of how much fresh water that is used during a cooling sequence in the water based heating/cooling system of the reactors and give a suggestion of a suitable reuse for this water.The main result is a total survey of the energy consumption in steam and electricity. The survey shows that the second largest group after drying is heating of ventilation which gives big potentials of reducing the total steam consumption if there is a way of being self supporting in ventilation heat.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

This thesis includes an energy survey of the Herrgården pre-school, which has a modern heating- and ventilation system, and a comparison with Östers pre-school which has an older system. An energy survey of Östers pre-school has already been done by a group of three students and all the calculations and values have been collected from that survey. As of today, both pre-schools are heated thru district heating. It will be much easier to make smart and feasible energy-saving-measures by first conducting the energy survey.Herrgården pre-school in Gävle houses 81 children, therteen teachers, one cleaner and one cook. It was finished in the middle of 2009 and the staff has been very pleased with the in-door climate.

The Rya power plant in Borås produces district heating, district cooling and electricity. The plant is owned by Borås Energi och Miljö AB and is run by Dalkia Facility Management AB.In order to get the best heat exchange from the district hot water a pair of twin pumps and a turbine circuit pump are used as return pumps. Turbine circuit pumps are used to increase the pressure through the heat exchangers at the power plant. The pumps are in use when the flow is over 2 000 m3 h-1 and during the summer when re-cooling is used to improve the effectivens of the heat boilers.Since the pumps, that are parallel connected, rotating at a fixed rate per minute, the pressure is regulated with regulating valves. This report shows that during the 4,300 hours that the pumps where in use, energy corresponding to 590 MWh was wasted.

Agricultural drainage ditches are links between fields, lakes and oceans, having the potential to transport e.g. sediment and nutrients. When in a good condition, drainage ditches can act as sinks for e.g. phosphorus and sediments and prevent eutrophication downstream. The aim of this study was to determine the condition of one agricultural drainage ditch and to come up with suggestions for appropriate measures. The aim was also to determine which of the ditch?s properties that were possible to evaluate visually, which processes they represented as well as which properties required complementary physical analysis. This in order to contribute to the work of developing a method for determining the status/condition of agricultural drainage ditches.

This thesis includes an energy survey of the Herrgården pre-school, which has a modern heating- and ventilation system, and a comparison with Östers pre-school which has an older system. An energy survey of Östers pre-school has already been done by a group of three students and all the calculations and values have been collected from that survey. As of today, both pre-schools are heated thru district heating. It will be much easier to make smart and feasible energy-saving-measures by first conducting the energy survey.Herrgården pre-school in Gävle houses 81 children, therteen teachers, one cleaner and one cook. It was finished in the middle of 2009 and the staff has been very pleased with the in-door climate.

This thesis includes an energy survey of the Herrgården pre-school, which has a modern heating- and ventilation system, and a comparison with Östers pre-school which has an older system. An energy survey of Östers pre-school has already been done by a group of three students and all the calculations and values have been collected from that survey. As of today, both pre-schools are heated thru district heating. It will be much easier to make smart and feasible energy-saving-measures by first conducting the energy survey.Herrgården pre-school in Gävle houses 81 children, therteen teachers, one cleaner and one cook. It was finished in the middle of 2009 and the staff has been very pleased with the in-door climate.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.