I want to look at the possibilities to start selling hot water from a small district heating plant with bioenergy. My reason for doing this project is to look at a new business opportunity for our farm. Our company have less work during the winter time compared to the spring and this project will give us more work during the winter. I also want to take as much material as possible for heating from our farm in order to increase the value of the products from the farm. The project is in a village near us, where we should support a school, a churh, a home for the aged, a kindergarten and a parish hall with heat. In my work I have compared two different alternatives with each other. The first alternative is to put a central heater in one of the buildings, the home for the aged, in which we will burn oat.

This report is made as a literature review, focusing on the work done to increase understanding of efficiency in the categories of substations and secondary heating systems, with respect to the deviation from the theoretically possible cooling off in the distribution network as well as the economic benefit that appear. The main purpose of a considerable part of the literature used in this report addresses the issue of identifying individual causes of reduced cooling in district heating systems. These literature resources have been compiled and summarized as part of the report.The technology of district heating is associated with benefits such as better use of the energy in a fuel. This is the case of cogeneration plants where serial generation of electricity and thermal energy increases efficiency compared with the parallel generation where heat is generated locally and electricity is generated centrally. Serial generation thus allows for lower primary energy demand.

The aims of this project were to describe the circumstances around dogs being left alone in cars, to investigate owners? knowledge of the risks associated with leaving dogs in cars and the relevant legislation and, finally, to study how changes in the air temperature and air composition in the car affect the dog. The project consisted of a survey of the literature, a questionnaire part and an experimental part. An important conclusion is the importance of the level of knowledge of owners, since there are several ways in which an owner can prevent their dog from heat stroke and, in the case of an eventual accident, their action can have direct consequences in minimizing the long-term damage to the dog and even whether or not it survives. Fewer than half of the owners in the study knew that for a dog suffering heat stroke, the most important thing is to bring the body temperature down. Only a third of dog owners knew that if a dog is left in a warm car and showing signs of heat stress, then the police should be contacted and the dog quickly helped out of the car.

Heat and power stations are often in need of optimizations. A simulation model is a tool for findingways to optimize the plant. The scope of this diploma work is to develop a simulation model ofBoiler 5 at Mälarenergi AB. Boiler 5 is a circulated fluidized bed boiler that was taken into service inyear 2001. Among the included parts in the boiler are cyclone, convection part andINTREX-chambers.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

Due to global climate change and the rising levels of greenhouse gases (GHG) in the atmosphere, the interest for seeking solutions for mitigation has increased. While much attention has been directed towards technical solutions such as carbon capture and storage (CCS), biogenic carbon sinks has also garnered significant attention. Previous studies have shown that coastal ecosystems such as seagrass meadows and mangroves have a much greater capacity for storing carbon (C) compared to terrestrial ecosystems. That raises the question if other coastal ecosystems, such as coastal wetland forests, that previously haven?t been considered as blue carbon habitats also contribute to coastal carbon sink capacity.

AbstractWith increasing population and increasing demands for comfort and thus an increase in energy demand, it is necessary to examine various energy-efficiency measures. This work deals with the ability to control the flow through the heating system to achieve the desired comfort with as little energy as possibleA heating system contains of different parts, roughly speaking, you can divide it to three main components: Heat source, Distribution and Heat emitters. All components are working together to bring heat to the building. What is examined in this report are different ways of adjusting the flow and supply temperature and how it affects comfort and energy use in a building.At today ?s date the conventional method is to use a high flow through the heating system, which affects pressure drop and cooling of the fluid.

This thesis examines a possible control strategy to minimize flow fluctuations in Uppsala?s district heating system. High variations in flow rate may lead to complications caused by hydraulic constraints in the district heating system. These complications, such as inadequate pressure and temperature levels, increase the risk of heat delivery failures. It is therefore important to avoid such situations both for the producer and for the customers.Typically, the forward temperature is controlled by using a rough correlation with respect to the outdoor temperature.

Carbon dioxide in the atmosphere contributes to the greenhouse effect, which is essential tolife on our planet. Furthermore, it plays an important part of the photosynthesis andrespiration of the world?s organisms. Since the start of the industrial revolution the amount ofcarbon dioxide in the atmosphere has increased exponentially. The main source is theextensive burning of fossil fuels.

Chapter 1 defines the aim of the project and gives a general orientation about ground heat extractors. In chapter 2 physical processes that could be expected to be involved in the heat transport around a ground heat exchanger are discussed. It is shown from a literature study what amount of moisture transport due to thermal gradients there could be expected in a ground heat exchanger. The conclusion is drawn that the moisture gradient (Sr) is of same magnitude as the driving temperature gradient (°C). At the expected amount of increased moisture around the pipes the moisture transport could be considered to have a little effect on the brine temperature.

Norconsult AB has developed a solarhousing concept, a house designed for the warm climate in the Middle East andwith large quantities of solar panels installed. The cooling system for the house was designed in an earlier report, the purpose of this thesis is to investigate the possibility of short and long term storage of thermal energy via an underground energy storage volume.Two different designs of the storage and three different filling materials have been integrated into a model to simulate different cases. The first design consisted of pipes installed in the ground, without insulation. The second design consisted of an insulated concrete box installed to prevent thermal energy from the surrounding soil to flow towards the lower temperature regions within the storage. The three different filling materials were dry saudi sand, water saturated saudi sand and the filling material used by the client for energy storage in Sweden.The results from the simulations show that neither of the designs, regardless of the filling material, managed to extract enough thermal energy from the house to the ground to uphold the demands of indoor climate.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

The rising demand for electricity and heat raises a big challange for the society and engineers. Many products have been introduced to the market to supply more energy to the energy systems. Absolicon AB is a Swedish company that develops and markets a combined heat and power generating product. The product, Absolicon X10, uses a parabolic trough to concentrate the radiation of the sun onto a receiver. The receiveris equipped with mono crystalline solar cells and is cooled by a circulating liquid media.

Biogas is a gaseous fuel, rich in methane, produced through a biological route in an anaerobic digester. A gas engine generates combined heat and power, which can be used at the farm to reduce energy cost. The process also generates a digestate, with better utilization of nutrient compared to cattle manure. The aim of this study is to analyze the profitability of a farm-scale biogas plant for combined heat and power (CHP) at Wapnö. Wapnö is an agriculture company located in the southern part of Sweden.

The energy in laundry rooms, in form heated air, can be utilized with a heat exchanger. A concept and an early prototype of the heat exchanger have already been developed to show that the theory works. This report describes the continued development and construction of the product.A field study was made in order to investigate the environmental usage and establish the product design. The most common washing machine was used as a calculation model, and calculations were also made to estimate the amount of energy in the air. A previous analysis of the existing prototype is also presented in this report, to show the products potential capacity.