Abstract Background: In 1997 the Kyoto Protocol was signed, it?s an international agreement which is aimed to reduce greenhouse gas emissions. Sweden's goal is to reduce energy using in buildings with 20 percent by 2020 and 50 percent by 2050. This is a comparison with levels from 1995 (Glad, 2006). For Sweden to be able to reach its goals, they need to construct more low-energy buildings (Åhman, Wahlström & Lundblad, 2010).

Each year, the coffee machines at Ericsson in Kista produce around 100 tons of ground coffee waste.The companies Coor Service Management, Löfbergs Lila and Selecta are all responsible for differentstages in the logistical chain in delivering coffee and, together with Ericsson, they want to increasetheir environmental benefit. The plan is to produce biogas through anaerobic digestion instead ofincinerating the coffee waste in a heating plant. The results are to be presented as different businesscases in which different biogas plants are compared with the reference case (heating plant),comparing costs and environmental impacts.There are two major environmental benefits from producing biogas; reduced carbon dioxideemissions from when fossile fule is replaced by carbon neutral biogas, and reduced emissions fromreturning digestate from the bio reactor to farmland instead of using industrial fertelizer.In order to determine the biogas potential in coffee waste, a couple of properties had to bedetermined in a laboratory. Properties such as the dry substance content, heating value, moisturecontent and ash content. The results show that 100 tons coffee waste could produce around 16 500Nm3 biogas which would contain 163 MWh.The biogas reactor and upgrade plant both need energy gas to function and uses around 14 MWh ofthe produced gas.

To fulfill the climate target that EU and the Swedish government have decided to apply, it becomes increasingly important that the energy efficiency of existing buildings and making new buildings energy efficient as possible. Of Sweden?s total energy consumption in 2011 was 40% used by residential and service. Of the 40% of the energy consumption was 60% used for heating and domestic hot water. A report from year 2012 shows that one reason why the heating volume is so great could be due to underestimating on the energy consumption for the heating in the planning of the building.

During the past 30 years the fuels for energy production in heating and power plants have changed. Fossil fuels have decreased in usage whereas bio fuels in Sweden have increased with 60% since the 1970's. Different fuels affects combustion and the release of various substances and particles into the flue gas. This is caused by the diverse components and chemical structures of fossil fuels and bio fuels. When the flue gas leave the combustion chamber and enters the path to the chimney particles in the gas are being transported out of the combustion chamber.

Gävle kommun har som mål att öka cyklandet i Gävle. År 2025 ska andelen resor kortare än fyra kilometer vara 60%, i senaste undersökningen från år 2012 låg den andelen på 24% (Atterbrand et al, 2012). Enligt samma undersökning konstaterades det att Gävle kommun inte är på väg att uppnå sina mål då andelen kortare resor som genomförs med cykel har stått på samma siffra sedan 2006 (Indebetou et al, 2012).Examensarbetet syftar till att ta fram ett koncept som uppmuntrar fler människor till att välja cykeln framför andra färdmedel. Problemformuleringen handlar om hur intresset för att cykla i stadsmiljö kan ökas.Arbetet har begränsats till att fokusera på en lokal nivå, men tanken är att resultatet ska kunna användas för att skapa liknande produkter till alla stadsmiljöer.Metoder som har använts för att komma fram till slutresultatet är intervjuer med privatpersoner och nyckelpersoner inom Gävle kommun, litteraturstudier, funktionsanalys och marknadsundersökning.Till undersökningen har matrial från Gävle kommun använts, men även vetenskapliga artiklar och intervjuer. Här används fakta för att styrka anledningar till varför personer bör välja att cykla framför andra färdmedel samt vad Gävle har för potential som cykelstad.I genomförandet visas flera skissförslag som tagits fram med inspiration från undersökningen.

A patient simulator for testing anaesthesia machines has been developed at Maquet Critical Care AB, to reduce costly and time-consuming experiments on animals. The device simulates human lungs regarding lung dynamics and volume, uptake of anaesthetic agents and the production of carbon dioxide, heat and moisture. Further demands on the simulator are durability and size; the device shall be compact enough to be moveable.The resulting simulator fulfils the requirements and enables better repeatability and ability to test extreme cases than experiments on animals do.Uptake of the anaesthetic agent is achieved in a active carbon filter and controlled by regulating the flow. The flow is created by a regenerative blower and controlled using a proportional valve. The uptake can be set by the user or by a simple uptake model modified to recursively handle changes in the concentration of anaesthetic agent.Carbon dioxide is fed into the system from a tank by a mass flow regulator.

The housing sector uses 40 % of the energy in Sweden and half of the electricity usage. Theuse of energy is the main reason to the increasing rate of carbon dioxide in the atmosphere.This is the main motive but also a wish of higher safety, that is a higher rate of selfsufficientenergy production in Sweden, we want to decrease the need of using fossil fuel. Now whenthe energy price rise, the interest in energy issues increase and more people discuss thepossibility of reducing the usage of fossil fuel. A change to renewable energy such as sun,wind and water is the only solution where we can get a sustainable development.One way to contribute to a better use of energy is to build in the principle of passive house.The house is being built with a thick and tight insulation. If you use a heat-exchanger withhigh degree of efficiency and a final heating battery on the ventilation system, the heat fromlamps, devices and the ones living in the house should be enough to fulfil the criteria ofliving.

SammanfattningEn ånganna monterades i EGR (Exhaust Gas Recirculation) slingan på en 12,7 liters Scania Euro V motor (DC1306). En modell som beskriver Rankine cykel togs fram med vatten som köldmedium i simuleringsverktyget GT-Power. Ångpannan i GT-power modellen kalibrerades m.h.a experimentell data.Simuleringarna visade att det optimala ångtrycket, det trycket där högst effekt kan erhållas från expandern, är beroende av EGR temperaturen. Det innebär att ju högre EGR inloppstemperatur desto högre optimalt ångtryck. EGR temperaturen i punkt 2 i ESC cykeln är 514? C för denna motor, vilket resulterar i ett optimalt tryck på 120 bar enligt simuleringen.

The housing sector of today represents for almost 40% of the energy consumption, an energy consumption of which the major part consists of non-renewable energy sources. This is not sustainable and utilization of new energy-efficient technologies in buildings can be a step in the right direction, towards a sustainable energy society.This report has been made on behalf of and in cooperation with Älvstranden Utveckling AB in Gothenburg to examine how future energy-efficient technologies can affect the energy demand in energy-efficient multi-dwelling buildings.The report is based on Älvstrandens passive house, Hamnhuset, a house whose energy consumption is far below the BBR's requirements. The report looks at the opportunities for improvement within windows, insulation, solar energy technologies, as well as white goods. Computer simulations are then made to apply the selected technologies into a reference building. Technologies are selected from an energy efficient perspective and no account has been taken of other aspects such as the economy.

The Scanian woodfences has been determined by two mainly elements: Scania's composition of tree species, with a large element of deciduous forest, and the local building tradition which has more in common with the European continent than the Swedish tradition. By examining responses from ethnological question lists deriving from the first half of the 1900s, combined with literature studies, I have been able to deepen and broaden the knowledge behind the various fencing design. In addition I ?ve constructed maps which could illustrate their historical geographic distribution.I have come to the conclusion that there was three main types of woodfences that was most common until the barbed wire was introduced in the early 1900s and later on replaced the elderly woodfences. Common for the three main types is that the base material was made out of Juniperus communis, this largely because of its durability against rot.

This paper examines the possibility of identifying votive offerings among a collection of stray finds in a Late neolithic material from one farm land on the island Hven.First, I identify the Late neolithic artefacts in a collection of stray finds and make a register as well as take photographes of the artefacts. Then I compare these stray finds with material from hoards found in Scania to analyz if any similarities arise regarding length, fragmentation and patina. Additionally, I use maps to identify wetlands and a field survey to help identify and discover important areas connected to votive offerings. There is a strong possibility that the stray finds collection contains some votive offerings because similarities can be found between the lengths of the stray finds and the materials from the hoards..

In developing countries such as Vietnam the population consumes more animal products for example milk and meat than before which requires greater livestock production. Ruminants contributes to more methane emission which creates a dilemma between food production and its environmental impact. By feeding ruminants with nutritive crops which humans can not assimilate the animal performance will increase in terms of better growth and milk production without inpinging on food that can be consumed directly by humans. Increasing animal performance reduces methane emission in terms of amount of methane in kg-1 milk and meat which today is much greater in developing countries than developed countries. The aim of the study was to investigate tropical tannin-rich legumes for their potential as a feed supplement for ruminants made in vitro.

In this thesis work a Geographical Information System (GIS) based methodology to identify locations suitable for the installation of wave energy converters has been developed. Parameters of importance have been identified and a GIS-database has been set up, containing data about the marine environment. In a case study of the Swedish west coast the methodology has been applied, resulting in a number of maps showing possible areas. The results show that large areas are suitable for installation of wave energy converters, from a technical and economical point of view. When consideration is taken to other interests in the area, such as navigation, fishing and environmental protection, the size of the suitable area diminishes considerably.

Academic research concerning how to determine the power situation in a supply chain where an investment product supplier is involved did not exist. Therefore new models has been developed that analyses the power relations and maps out the power situation in a supply chain. In the future these models can be applied on similar cases by modifying the included parameters. The new models show that case company FAS should focus on the big producers of garbage bag which are Trioplast, Rullpack and Miljösäck. By strengthen the brand FAS can make more money in these relations.

By using steady-state measurements for predicting emissions under a dynamic drive cycle wouldsave a lot of time and money for the exhaust aftertreatment specialists at Volvo cars. The idea forthis thesis has been to investigate if statistical regression models can be used with good accuracy.Questions included are for example if common operating variables such as engine speed, air-fuelratio etc. is sufficient to predict engine-out emissions over the engine operating range with goodaccuracy. Focus was set on the modelling of warm engine, but also the more complex engineheat-up phase was investigated since it is a great contributor to total emissions. While NOxcouldnot be measured because of malfunctioning measurement equipment, only HC, CO andtemperature at inlet of first catalytic converter has been modelled.