In cooperate with Asko Cylinda we have developed a new heat system too short the processtime and reduce the energy consume in a dishwasher and still have it too be a class AAA.The environment and quality is important for the company too still be the number one onthe market, If they want too keep that position the product developed of new innovations willbe very important. The systems we have developed are more effective and reduce energy uptoo 25 %. The process time is reduced too less than two hours, from the today two andhalf-hour. The solutions are too heat up the rinse water and the dishwater at the same time,with a new heating system and it make are solutions unique and effective. Its good for thedish and the environment.

Författarna har genom studien funnit att faktorerna engagemang, tidigare internationell erfarenhet, systematiskt tillvägagångssätt, företagets storlek,nätverk och kunskap haft tydligast påverkan på de studerade svenska företagens internationalisering och framgång i Ryssland. Dessa framgångsfaktorer tycks även likna de faktorer som generellt framträder i tidigare forskning. Dock framstår möjliga marknadsspecifika element som kan kopplas specifikt till den ryska marknaden. Dessa framgångsfaktorer kan inte enskilt förklara företagens framgång, utan ger en nyanserad bild av de studerade företagens främsta attribut vid etableringen..

Works on transparent paper, also commonly known as tracing paper, have been described as ephemeral or temporary working documents and they usually number large quantities in archival and museum collections. They have therefore previously been considered of lower priority and can be found in poor condition due to a lack of treatment or suitable storage prospects. In addition, transparent paper can be very sensitive to moisture and reacts by deformation or loss of transparency. Due to the volume of these works and the necessity of treatment, there is a call for simple and efficient conservation methods. A common solution in archives for the treatment of water-sensitive works on paper has been the use of heat-activated tissues as they can be applied without the introduction of solvents. There is little published about the use of heat-activated tissues on transparent paper and is mentioned only briefly in existing literature.

The purpose of this thesis has been to determine experimentally how good a peltierelement is to convert waste heat from wood burning. Three different peltier elementswere used in a comparison study. The comparison was mainly done to know howmuch power could be obtained from each element. Even, a circuit with a step-upfunction has been created to give a higher output voltage than the peltier elementitself. The result of the experiments was a low output power, the highest valuereached 2.18W.

I want to look at the possibilities to start selling hot water from a small district heating plant with bioenergy. My reason for doing this project is to look at a new business opportunity for our farm. Our company have less work during the winter time compared to the spring and this project will give us more work during the winter. I also want to take as much material as possible for heating from our farm in order to increase the value of the products from the farm. The project is in a village near us, where we should support a school, a churh, a home for the aged, a kindergarten and a parish hall with heat. In my work I have compared two different alternatives with each other. The first alternative is to put a central heater in one of the buildings, the home for the aged, in which we will burn oat.

The report addresses four main tasks, situation analysis of the company's total costs and transportation volume, cost analysis associated with the adjustment of the filling ratio, transport costs for the expansion and new expenses on a combination of expansion with new adjusted filling ratio.  Increasing transport costs for the company was the main reason for the request of the current situation analysis. A survey of the total cost with the actual volumes and transport provider pricing is the basis of the analysis that extends from May 2006 to October 2008. The results show an increase in costs, both overall expense and per cubic meter of transported goods. Volume spreads, trends, and seasonal variations are according to our and the company?s expectations.

The aims of this project were to describe the circumstances around dogs being left alone in cars, to investigate owners? knowledge of the risks associated with leaving dogs in cars and the relevant legislation and, finally, to study how changes in the air temperature and air composition in the car affect the dog. The project consisted of a survey of the literature, a questionnaire part and an experimental part. An important conclusion is the importance of the level of knowledge of owners, since there are several ways in which an owner can prevent their dog from heat stroke and, in the case of an eventual accident, their action can have direct consequences in minimizing the long-term damage to the dog and even whether or not it survives. Fewer than half of the owners in the study knew that for a dog suffering heat stroke, the most important thing is to bring the body temperature down. Only a third of dog owners knew that if a dog is left in a warm car and showing signs of heat stress, then the police should be contacted and the dog quickly helped out of the car.

Heat and power stations are often in need of optimizations. A simulation model is a tool for findingways to optimize the plant. The scope of this diploma work is to develop a simulation model ofBoiler 5 at Mälarenergi AB. Boiler 5 is a circulated fluidized bed boiler that was taken into service inyear 2001. Among the included parts in the boiler are cyclone, convection part andINTREX-chambers.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

AbstractWith increasing population and increasing demands for comfort and thus an increase in energy demand, it is necessary to examine various energy-efficiency measures. This work deals with the ability to control the flow through the heating system to achieve the desired comfort with as little energy as possibleA heating system contains of different parts, roughly speaking, you can divide it to three main components: Heat source, Distribution and Heat emitters. All components are working together to bring heat to the building. What is examined in this report are different ways of adjusting the flow and supply temperature and how it affects comfort and energy use in a building.At today ?s date the conventional method is to use a high flow through the heating system, which affects pressure drop and cooling of the fluid.

This thesis examines a possible control strategy to minimize flow fluctuations in Uppsala?s district heating system. High variations in flow rate may lead to complications caused by hydraulic constraints in the district heating system. These complications, such as inadequate pressure and temperature levels, increase the risk of heat delivery failures. It is therefore important to avoid such situations both for the producer and for the customers.Typically, the forward temperature is controlled by using a rough correlation with respect to the outdoor temperature.

 Introduction and research question: In the global media field, global expansion has become more common and is a way for media companies to reach out to a broader audience. Both advantages and disadvantages come with a global expansion and there are several cultural differences that have to be considered. This thesis will deal with the cultural differences and discuss how a Swedish media company efficiently goes about establishing in Vietnam. This leads us to this thesis' research question: How does a Swedish media company succeed in Vietnam? Purpose: This thesis' purpose is to find out what media companies do to successfully acclimate to the Vietnamese culture and the important aspects of the cultural differences to consider.Delimitation: In order to present a thesis with greater depth and acquire a deeper understanding, the study is limited to examine Swedish media companies and what intercultural aspects are important to consider when establishing in Vietnam. Method: The research we have done is based on interviews, which we thought could give us the accurate information and a good base to stand on.

This Master?s thesis is a comparative study of information retrieval results between three distinct search strategies in simulated automatic query expansion in a bibliographic database. Our purpose is to investigate which of the search strategies score the most effective precision and to what extent the same relevant documents are retrieved (overlapped). A thesaurus attached to the database is used to select appropriate descriptors for the baseline query formulations which subsequently are expanded with hierarchical relations. The search strategies are s1: A baseline query with two or three descriptors, s2: The baseline descriptors combined with at least one Narrower Term, s3: The baseline descriptors combined with Narrower Term and at least one Broader Term.

Chapter 1 defines the aim of the project and gives a general orientation about ground heat extractors. In chapter 2 physical processes that could be expected to be involved in the heat transport around a ground heat exchanger are discussed. It is shown from a literature study what amount of moisture transport due to thermal gradients there could be expected in a ground heat exchanger. The conclusion is drawn that the moisture gradient (Sr) is of same magnitude as the driving temperature gradient (°C). At the expected amount of increased moisture around the pipes the moisture transport could be considered to have a little effect on the brine temperature.

Norconsult AB has developed a solarhousing concept, a house designed for the warm climate in the Middle East andwith large quantities of solar panels installed. The cooling system for the house was designed in an earlier report, the purpose of this thesis is to investigate the possibility of short and long term storage of thermal energy via an underground energy storage volume.Two different designs of the storage and three different filling materials have been integrated into a model to simulate different cases. The first design consisted of pipes installed in the ground, without insulation. The second design consisted of an insulated concrete box installed to prevent thermal energy from the surrounding soil to flow towards the lower temperature regions within the storage. The three different filling materials were dry saudi sand, water saturated saudi sand and the filling material used by the client for energy storage in Sweden.The results from the simulations show that neither of the designs, regardless of the filling material, managed to extract enough thermal energy from the house to the ground to uphold the demands of indoor climate.