This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

The rising demand for electricity and heat raises a big challange for the society and engineers. Many products have been introduced to the market to supply more energy to the energy systems. Absolicon AB is a Swedish company that develops and markets a combined heat and power generating product. The product, Absolicon X10, uses a parabolic trough to concentrate the radiation of the sun onto a receiver. The receiveris equipped with mono crystalline solar cells and is cooled by a circulating liquid media.

Biogas is a gaseous fuel, rich in methane, produced through a biological route in an anaerobic digester. A gas engine generates combined heat and power, which can be used at the farm to reduce energy cost. The process also generates a digestate, with better utilization of nutrient compared to cattle manure. The aim of this study is to analyze the profitability of a farm-scale biogas plant for combined heat and power (CHP) at Wapnö. Wapnö is an agriculture company located in the southern part of Sweden.

The energy in laundry rooms, in form heated air, can be utilized with a heat exchanger. A concept and an early prototype of the heat exchanger have already been developed to show that the theory works. This report describes the continued development and construction of the product.A field study was made in order to investigate the environmental usage and establish the product design. The most common washing machine was used as a calculation model, and calculations were also made to estimate the amount of energy in the air. A previous analysis of the existing prototype is also presented in this report, to show the products potential capacity.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

In this work an assessment of the compressed air system in the facilities of Vattenfall Heat Uppsala has been conducted. The facilities constitutes, among others, a combined heat and power plant, and two waste incineration plants. The compressed air is supplied primarily by seven rotary screw compressors and yearly electric energy consumption in these has been determined. Furthermore, the usage of compressed air has been mapped in order to find processes with energy savings potential. Several suggestions how to reduce the usage of compressed air have been presented, resulting in decreased need of electric energy and reduced CO2-emissions.The results show that total need of electric energy in the compressors, during a standard production year, amounts to 5.83 GWh.

Uppsalahem AB is a municipally owned real estate concern that owns and administrates housing for nearly 30 000 people. The company puts a lot of effort into reducing the energy use of their housing stock. This project is a master?s thesis in the energy systems programme at Uppsala University, carried out in collaboration with Uppsalahem. The aim of this thesis is to provide energy saving measures for fourteen student housing buildings in Uppsala, Sweden.

Sala Silvergruva AB är ett av många företag som just nu kämpar med höga energi-kostnader. Denna rapport undersöker vilka möjligheter det finns att skapa ett hållbart energisystem i Sala Silvergruva med avseende på ekonomi, miljö samt sociala aspekter. Rapporten undersöker nio tekniker; vindkraft, vattenkraft, solfångare, solceller, pelletspannor, värmepumpar, effektivisering samt lagring av värme från växthus respektive fjärrvärme. Dessa analyseras var för sig med utgångspunkt i tio krav som speglar hållbarhetsaspekterna. I samband med analysen ges rekommendationer angående investering i respektive energilösning. Rapporten mynnar ut i en resultatskarta där det tydligt framgår vilka krav de olika teknikerna uppfyller. Den följande diskussionen leder fram till en slutsats som presenterar vilka åtgärder som bör vidtas i syfte att skapa ett uthålligt energisystem för Sala Silvergruva AB. Pelletspannor och värmepumpar visar sig i nuläget vara de mest uthålliga tekniklösningarna.

The milk production per cow has increased considerably during the last 50 years and due to the breeding for higher milk production also brings decreased reproduction efficiency. In a Swedish study 1996 it was shown that on average only half of all estruses were detected. Every time a farmer fails to detect oestrus it costs the farmer about 1200 Swedish crones and the need of means of detecting oestrus is therofore large. With this study we wanted to investigate if heart rate respectively crystallisation of vaginal mucus (arborisation) could be useful means of detecting oestrus. We monitored two oestrus cycles in four heifers.

The company Sol & Energiteknik wanted to examine the possibility to make a standardhouse totally energy independent. Based upon this I have, during the spring of 2007,examined the possibilities available at the market today through litterature studies, contactwith several companies and reading reports at the internet.The first thing to examine has been to determine the energy consumption for a standardhouse, and find out if there are better technologies to be used for energy conservation.My conclusion in this matter is that there are possibilities today for building a house moreenergy efficient.When I had reached the point at which my design for the house was decided, I also hadto choose the different products to use to produce energy as well as to store that energy.To produce heat and electricity to the house I decided to use a wind turbine and a solarwater heater.The most difficult part of designing a house that is energy independent is that theproduced energy must be stored somehow. Storing the heat is relatively easy beacuse theheat can be stored in a large water tank. The electricity is a bigger problem beacuse itmust be stored in batteries, which today are too expensive to be used in a standard house.In the future producing and storing hydrogen might be used to produce electricity, buttoday that technology is both expensive and not tested enough.My final conclusion is that a standard house can not be built to be totally energyindependent today, unless it is very expensive to connect the house to the electricitynetwork. As an alternative solution I came up with a proposal for a house which isconnected to the electricity network and have some amount of own produced energy.This house prooved to be a good investment if you choose to build it today, and it couldbe a very good investment in the long run beacuse energy prices increase every year..

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The biogas plant Kungsängens gård, owned by Uppsala Vatten och Avfall AB, produces biogas and biomanure from organic household waste, food processing waste and slaughterhouse waste. In year 2012, 4.4 million Nm3 of biogas were produced from 25 200 tons of waste. Before digestion all substrate is sanitized by pasteurization at 70°C in order to kill pathogens. Another method, integrated thermophilic sanitation (ITS), is of interest in order to decrease the energy demand. The method implies that the substrate is sanitized during ten hours in the digestion chamber, where the temperature is 52°C.

The energy use in a workshop company has been examined in this work in order to find areas for energy efficiency improvement. The combined oil and electricity heating in the company were compared with other alternative heating systems including cooling of the premises in following combinations:Ground source heat pump for heating and coolingDistrict heating and absorption coolingDistrict heating and low temperate surface water coolingEnergy use, operation costs and carbon dioxide emissions were calculated for the current heating systems and the three alternatives including cooling. The ground source heat pump for heating and cooling decreases bought energy with 34 MWh annually compared to current heating only. The district heating and low temperate surface water cooling has the largest reduction of operation cost and carbon dioxide. The operation cost decreases with 42 kSEK and the carbon dioxide with 43 metric ton CO2 annually.

The need for snow-free surfaces at squares, bus stops, platforms, car parks and sports facilities increases and at the same time energy price rise and the environment is becoming a hotter issue. The construction of the ground heating systems often lack thermal insulation under the heating pipes, which means that the heat from the pipes not only warm up the soil surface but also heats the surrounding soil. The insulation also has more features, by insulating the risk of frost damage is minimized. The goal of this report is to demonstrate the large heat loss and energy costs in the absence of insulation under the heating system.The report begins with a scientific way to study and treating the soil heating system uses, and the theory involved. Furthermore it also deals with different routing principles of heat pipes depending on the facility.All calculations are made with so called finite element method (FEM), in COMSOL Multiphysics 3,5a, where models are created with different conditions.

Along with rising energy prices and increasing awareness of environmental issues, the criteria for buildings energy performance have been sharpened through the years. Today, ?passive house? and ?low energy house? are commonly used phrases in the construction industry and is expected to become increasingly common in the future.For houses with well-insulated building envelope the importance of well constructed details increases when minimizing the heat losses. Examples of these details are floor-wall junction and window openings in the wall. In such connections thermal bridges occur, which means that heat more easily is transported out of the building, compared to the rest of the building envelope.This report deals with detail solutions around windows and a comparison between a traditional slab and a foundation from Koljern consisting of foam glass.