This master thesis was initiated with the aim to answer at what level of installed capacity of wind power in the northern parts of Sweden it would be beneficial to improve the transmission capacity from the northern Sweden. During the process of this work the aim has changed to try and create a model that can be used to analyze how well the hydro power installed in the northern Sweden can even out the quick changes in wind power production.To create a good model of all hydro power in northern Sweden is a very large job, unfortunately too large for a master thesis. This report therefore ends with an extensive analysis of the simplifications that have been made and their effects as well as a list of the future work that has to be done.The model that has been created have shown to be effective and produce good results. The conclusions that can be made is that the northern Swedish hydro power have very good possibilities to balance the wind power production. Only a few cases where water have been spilled even though there has been some free capacity has been discovered.

Individual cellulose ?bers were studied to identify the transport and absorbtion phenomena as well as the in?uence of drying. A Chalmers University of Technologydeveloped method within ESEM (Enviromental Scanning Electron Microscope) has been used in this study. The results from the laborations gave the following conclu-sions: The transport of water occurs in ?bers in the ?ber wall surface and the lumen.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

Detta arbete undersöker 4 olika algoritmer som används för bred kollisionsdetektering. De olika metoderna för bred kollisionsdetektering kan delas in i 4 olika kategorier. Algoritmerna som är valda att representera varje kategori är Bruteforce, Sweep and prune, Hierarchical grid och Bounding volume hierarchy. Fokus i arbetet ligger i att mäta deras lämplighet för spelmotorer där det är viktigt att algoritmerna kan köras i realtid.Algoritmerna körs i simulationer av olika miljöer. Där antalet objekt, hur många som är rörliga och objektens distribution varieras mellan miljöerna.

In times of increased flooding, enhanced by climate change, polluted stormwater poses an increased threat to the environment through contaminated water entering waterways. Bioretention utilizes natural processes in soil and vegetation to treat pollutants and combat this threat. Biochar produced through pyrolysis, has a high cation exchange capacity (CEC) and could therefore increase treatment in bioretention systems. This research applies a literature review, interview, and a model to explore the benefits and disadvantages of biochar in order to specify a soil-mix through an understanding of the production process and preferred application rate. High purification through CEC, increased water holding capacity, and carbon sequestration being the benefits discussed.

Results have shown that flow batteries may be a solution in the future as an effective and environmental friendly method to an energy storage system (ESS). The technology is reliable and has a high efficiency that comes with low energy losses and a long lifetime. The range of possible fields is suitable for cutting energy peaks in the power grid, by always have a ready and available energy storage that balances the production. By comparing the advantages of flow batteries with conventional batteries it is mainly the fact that they can conserve energy for a long time without being self-discharged thanks to that the storage capacity is in principle endless and limited by the size of the electrolytes tanks that makes them a great energy storage system. The batteries won?t take any damage or decrease in performance when charging or discharging it or if you exhausts it to 100 % and leave it discharged for a long time.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

opera byggnad, innergård,betong , schakt, genomsiktlig, mesh, grid.

Wind power is expanding rapidly in Sweden. Increasing amounts of wind power sets higher requirements on balancing power and grid expansions and would affect the whole Swedish electricity system. The aim of this report is to examine the factors affecting the wind power expansion in Sweden. How many wind power plants projects will obtain building permissions and what costs and revenues can be expected? How much balancing power will be required and does a changing geographical distribution of the wind power plants reduce the need of balancing power?A survey of the county board?s official applications has been made and out of all the applications, corresponding to 80 TWh produced per year, about half of the applications are expected to obtain a permit with a major portion of them located in the north of Sweden.Especially older wind power plants, deriving revenue from Nord pool, find themselves today in a complicated financial situation.

Most companies have a bottleneck in their production, that is a constraining re-source. When the demand is higher than the capacity in the constraining resource it is impossible to produce the demanded output. This problem leads to delayed deliveries, unhappy customers and ultimately to decreased revenue. Bottlenecks therefore has a significant role in production and must be handled thereof.MW Power in Sävsjö, Sweden designs and manufactures water and steam boilers for the customer's unique needs. MW Power invested in a new plasma cutting ma-chine but the machine has not reached the expected capacity.

In Sweden more than 400 000 private households have not yet sufficient wastewater purification. These effluent is considered as an increasing problem and many onsite purification methods have been studied. In this investigation, the method of reactive bed filters have been tested by column and batch experiments. Five different kinds of filter materials with reactive surfaces have been studied concerning their capacity to absorb ammonium and phosphorus from wastewater. The materials that were examined are Filtra N, wollastonite Filtra P, blast furnace slag and Polonite®.

Today?s wind power plants are only compensated for their reactive power consumption at no-load. As the wind power plants grow bigger the amount of reactive power they need also increases. This is no longer a problem that can be ignored, especially as the net owners are beginning to charge the reactive power they transport.In this thesis a couple of different methods of compensation and their prices will be discussed and evaluated. Problems, such as self-excitation, that can occur if one fully compensates the wind power plant will also be brought to surface.

Today?s wind power plants are only compensated for their reactive power consumption at no-load. As the wind power plants grow bigger the amount of reactive power they need also increases. This is no longer a problem that can be ignored, especially as the net owners are beginning to charge the reactive power they transport.In this thesis a couple of different methods of compensation and their prices will be discussed and evaluated. Problems, such as self-excitation, that can occur if one fully compensates the wind power plant will also be brought to surface.

Previous studies of central tire inflation (CTI) in truck transport of roundwood have shown potential benefits to include more even wood flow and reduced road damage. The greatest benefits are found to be during periods of low bearing capacity such as spring thaw. No previous studies have examined geographical variations in the potential benefit of CTI-equipped trucks. The aim of the study was to develop and use a simple method for geographically prioritizing the use of CTI-equipped trucks within a forest company´s sector of activity.The host company for the study was Holmen Skog. The area studied consisted of Holmen Skog?s entire sector of activity extending from the province of Västerbotten to the province of Småland.

Today?s wind power plants are only compensated for their reactive power consumption at no-load. As the wind power plants grow bigger the amount of reactive power they need also increases. This is no longer a problem that can be ignored, especially as the net owners are beginning to charge the reactive power they transport.In this thesis a couple of different methods of compensation and their prices will be discussed and evaluated. Problems, such as self-excitation, that can occur if one fully compensates the wind power plant will also be brought to surface.