The knowledge of the chloride content and its fluxes and patterns in trees is insufficient. Increased knowledge would be desirable, one of many reasons is to be able to more efficiently meet the problems that the substance causes in the pulp industry. The purpose of this study was to examine and describe the chloride concentration of Norwegian spruce (Picea abies L. Karst.) in the south of Sweden. Furthermore the aim was to be able to predict chloride concentration from readily measurable site factors.

The purpose of this project was to investigate if retention of polar compounds that are given to treat tuberculosis, diabetes, inflammatory bowel disease and childhood leukemia could be obtained with HILIC separation. By varying different parameters for different types of columns the compounds were analyzed with the aim of finding guidelines for future method optimizations. To perform these analyzes three different columns were tested ? ZIC-HILIC (silica-based with zwitterions), ZIC-pHILIC (polymer-based with zwitterions) and XBridge Amide (amide functions). The results were evaluated with selected quality measures.

Superficial digital flexor tendon injuries are common causes of premature retirement or pre-longed convalescence periods for race horses. The curve gradient at Täby Galopp race track is very small and most races as well as high speed training are done on the left rein. It is believed that the horses left foreleg is under considerably more strain then the right foreleg when being ridden on the left rein during gallop at high speed. During gallop on the left rein the horse puts its entire weight on the left foreleg when regaining ground contact. The purpose of this study has been to find out, through analyzing the statistics concerning the horses that visited the ATG clinic at Täby during a period between January 2003 and September 2006, whether there is a higher frequency of superficial digital flexor tendon injuries on the left leg rather than the right and if so, can this support the theory that the design of the race track in combination with continuous left rein races can be a contributing cause of these injuries. The result of the study shows that 57% of the tendon injuries occurred on the left front leg and 38% on the right front leg. The difference is not large enough to support the above theory of the underlying cause of these injuries..

Long time-series of pressure measurements often have high quality because the early instrumentsare more or less the same as the modern ones. A time-series from Lund consisting of three dailymeasurements from 1780-1997 has been homogenised and is therefore suitable for analysingpossible influences of the enhanced greenhouse effect. According to a two-layer model of theatmosphere one finds a shift in the frequency of baroclinic instability due to an increasedtemperature gradient caused by the increasing CO2. Baroclinic instability over the Atlantic Oceanis the main cause for frontal zone production, causing cyclonic activity over the southern part ofScandinavia. Changes to the baroclinic instability would therefore be traceable in the time seriesfrom Lund.

This thesis is about a part of the marquetrytechnique, scorching. Scorching is made by heating up something, put a veneer into the heated substance and make a controlled burning. This technique is old but still used today and have according to me great potential for development. In my work I wanted to give the scorching greater room then I earlier have seen. I wanted the scorching to be the dominant ingredient for a decorative element in a piece of furniture or an interior.

Denna slutrapport är resultatet av ett samarbete mellan Kockums AB / Karlskronavarvet och Blekinge Tekniska Högskola (Institutionen för maskinteknik). Det av Kockums initierade projektet har benämnts till ?System med ?Pop-up?-munstycken för helikopterplattform på korvett?. Uppdraget har bestått i att utprova och verifiera ett befintligt munstycke, vars primära funktion är släckning av petroliumbränder (helikopterolycka) på ett stelthfartygs helikopterplattform. Munstyckets sekundära funktion består i att vattenbegjuta (sk.

AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

Denna slutrapport är resultatet av ett samarbete mellan Kockums AB / Karlskronavarvet och Blekinge Tekniska Högskola (Institutionen för maskinteknik). Det av Kockums initierade projektet har benämnts till ?System med ?Pop-up?-munstycken för helikopterplattform på korvett?. Uppdraget har bestått i att utprova och verifiera ett befintligt munstycke, vars primära funktion är släckning av petroliumbränder (helikopterolycka) på ett stelthfartygs helikopterplattform. Munstyckets sekundära funktion består i att vattenbegjuta (sk. wash-down) stelthfartyget, för att minska dess IR-signatur och för användning vid NBC-sanering (Nuclear, Biological and Chemical).

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.