The dissertation were performed on SP, Technical Institute of Sweden. The dissertation were carried out on the measurement technical department, this dissertation is a part of a bigger project, project ClampCal. One of SP?s returning assignments are flow-measurement. When flow-measurement is performed, the flow has to be stopped so that a meter can be installed in the pipes where measurement is going to take place. At every stop there is time delay in the flow which causes the customers to loose money. This is why SP wanted to find a better solution so that measurement can be done without any stops in the flow. Usage of a so-called Clamp-on meter was considered, but since the measurement uncertainty is too large it takes some investigation on the parts where the largest uncertainties occur and thus find a solution that can diminish the uncertainty as much as possible. The parts that were considered to have an opportunity to reduce measurement uncertainties were the fluid temperature, its characteristics and the pipe geometry and its characteristics. For the fluid temperature a Pt100-sensor with four different radii for various pipes was used.

In central Jönköping, on Munksjöns northern waterside a shopping centre will be built, on the block Atollen. The construction will begin in autumn of 2007 and will be finished according to plan in 2009. Atollens goal is to counteract the competition from external retailers and strengthen the retail trade in the city centre, leading to more attractive and competitive city centre.Atollen will not be a shopping centre in traditional style and design, it will be focused on shopping and experience. The shopping centre shall be a natural venue with a wide and exclusive store mix, concentrated against trend conscious customers. This will be created with the help of a futuristic design and architecture, with light, open and transparent spaces.

This master thesis was conducted at Motala Wire Works Ltd (MWW) in Motala during the autumn and winter of 2007-2008. The thesis named ?Future layout of Motala Wire Works? focuses on making a better planed layout for the factory, which also take in to consideration future changes.Motala Wire Work produces wire mesh products of varying sorts for the white goods industry. The factory was started by Electrolux during the 1950?s.

This examination work is performed at the institution of industrial economy and production at Jonkoping technical university, for JELD-WEN Door Solutions plant in Forserum.Today the focus in the company is on to reduce their inventories binding of capitals as well as inventory of products and that includes to get a good control of the supply and handling of material which is of great importance.JELD-WEN Door Solutions is one of the worlds leading producers of windows and doors and the head-office is located in Oregon, USA.A great number of wooden doors are manufactured by the company in varying of constructions, classifications and performance.The production of the plant in Forserum has a project- and customer focus manufacturing where only internal doors are produced. The overall market they are concentrated on is to different institution such as schools, hospitals etc.The purpose of this work is to investigate possibilities to improvement of material- and production control at JELD-WEN. The report will handle the master production schedule to and from the production divisions within manufacturing industry. Focus will be on the way for information- and material flows from arrival, transport within the company and further on to customers.Further a map of the flow was performed which gave a clearer picture of the connection between the flow of information- and material for the manufacturing process. On the basis of the mapping of the flow, the group discovered that the flow of material had some improvement potential.

Human Computer Interaction (HCI) handlar om att utveckla produkter med god användbarhet. Med användbarhet menas att system ska vara lätta att använda och lära. Jakob Nielsen är en av förgrundsfigurerna när det gäller riktlinjer för hur detta ska uppnås. Han har utvecklat tio kriterier som kan användas för att ett så bra system som möjligt ska kunna utvecklas.På senare år har forskare börjat se till, inte bara tekniska aspekter utan även till de känslor som användaren kan tänkas uppleva under det att denna interagerar med en webbsida. Ett flertal forskare har utvecklat teorier kring begreppet Flow.

Detta projekt genomfördes i samarbete med akustikern Erling Nilsson på företaget Ecophon i Hyllinge. Uppdragsgivare var musikproducenten Magnus Ågren som äger studion Flow Music i Malmö. Uppgiften var att förbättra akustiken i ett av Flow Musics studiorum. Rummet hade före projektet en hård och obehaglig akustik. För att komma fram till ett åtgärdsförslag specificerades först hur enskilda akustiska egenskaper skulle påverkas för att ge ett så bra resultat som möjligt.

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

The goal of this study is to examine what five teacher?s impression of the teacher?s role is in their previous years. How important the ?joy at work? is in relation with the educational progress? And what aspects that contributes to the? joy at work? and what obstacles that stops them. The essay will also go through the concepts of a teacher role, with connection to the theoretical perspectives of Csikszentmihalyi?s Flow and Antonovsky?s Salutogenesis (KASAM).The method I used was interviewing five teachers and I used Larsen?s chapter of ?content analysis? as a basis, I also used Flow and KASAM as theoretical references in my analysis.

This thesis examines a possible control strategy to minimize flow fluctuations in Uppsala?s district heating system. High variations in flow rate may lead to complications caused by hydraulic constraints in the district heating system. These complications, such as inadequate pressure and temperature levels, increase the risk of heat delivery failures. It is therefore important to avoid such situations both for the producer and for the customers.Typically, the forward temperature is controlled by using a rough correlation with respect to the outdoor temperature.

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

Electronic article surveillance (EAS) is widely used in shops and libraries together with an RF-tag attached to the goods or books in order to prevent shoplifting. By implementing the addition of a moisture sensor to the RF-tag, other functions become possible, including the ability to use as an alarm with regards to frozen goods, which have been shipped but which have melted and have, subsequently, refrozen. In- relation to care for the elderly, one time-consuming step involves checking whether there is the necessity for a change of diaper and this can, instead, be based on an RF-tag with an EAS-system alarm. A preliminary investigation was made using the moisture sensors, which involved how the resistance changes when liquid and/or heat is applied. A simulation of the LCCR circuit (RF-tag with the sensor) was conducted in order to determine how the resonance frequency changes for different resistances levels.

This diploma work on D-level is made in cooperation with Varnäsföretagen AB in Eskilstuna. The company performs contract manufactured aluminium goods. This work is a continuation on earlier diploma work in Varnäsföretagen AB. Even if the industry process consumes much energy for melting the aluminium goods, they consume a great amount of oil to warm up the building. The purpose of this work is to examine some places in the building and the process to see how much energy it is possible to recycles to the heating system and reduce the costs for heating.

In Sweden there are 1894 small-scale hydropower plants in operation, which together generate 4.3 TWh of electricity per year according to Swedish hydropower compound (SVKF, 2011). This corresponds to the annual consumption of about 860,000 Swedish households (based on an annual consumption of 5000 kWh). In the mid-1950s there were around 4000 small-scale hydropower plants in operation in Sweden before cheap fossil fuels and uranium competed with them, in the current situation only 1,894 of these are in use. If slumbering small hydropower plants once again would be taken into use and some new ones are built, we would be able to extract about 7 TWh of renewable electricity from these annually in Sweden, representing about 1.4 million households.The thesis intends to calculate and construct a hydroelectric power plant at the existing dam in Olofsfors and give suggestions on how the power station should run during the time that fish migration is greatest in Leduån.The turbine and generator to the station in Leduån at Olofsfors is designed by the height of the fall and the water flow through the dam. The turbine selected for the station is a CK-1000RM turbine with a 4-pole 250 kW generator from Cargo & power turbine Sweden AB, which is expected to deliver 1.2 GWh per year.

The system tungsten-oxygen has potential of being suitable for decorative coatings since ceramic coatings are often hard and wear resistant, and since modulations in oxygen content or incorporation of small ions could give bright colours. The aim of this report was to investigate the relationship between process parameters and  the properties of the films, with the wear resistance being of special interest.Samples with tungsten to oxygen ratios in the range of 100:0 to 25:75 at% were made using reactive sputter deposition, either with constant gas flow, or gas flow controlled by optical emission of the plasma. The hysteresis of the system, which means that a certain gas flow will cause different pressure and/or target voltage depending on in what way the flow is reached, makes it interesting to control the process where the system makes the steep change from metallic tungsten to ceramic tungsten oxide. This is difficult and thus requires precise control equipment.The samples were analysed using X-ray diffraction, X-ray photoelectron spectroscopy and an empirical wear test suitable for small components like cell phone cover for example, in order to characterize the structure, composition and wear resistance of the coatings. The results could be divided into three groups: (I) tungsten-like, with very low oxygen content; (II) mixed phase and (III) tungsten oxide like, with oxygen content close to 75 at%.

In this essay, I research and discuss new spirituality (or what is commonly known as New Age) within some congregations in the Church of Sweden, Gothenburg. I question how and why this new spirituality has come to be accepted in parts of the Church. My hypothesis is that the church is a part, and a reflection, of a larger change throughout society, and I claim that this change depends much on the individualization and globalization during the last decades.The research is conducted through interviews with representatives from the Church ofSweden who are in charge of new religious activities. During these interviews we discuss their views on the change that has already taken place and is going on today.The interviews are then analyzed by applying rational choice theory on them. I discusswhether the Church can be seen as a producer of goods and services and if the churchgoers canbe seen as consumers of these goods and services.