The comprehensive purpose of this Master of Science thesis is to examine which fleetmanagement services for engineering vehicles, ?Fleetech? preferablyought to develop inorder to reach a broad market and meet the demands of contractors.Scanty explained, fleet management is the management of a company's vehicle fleet and theservices can include a range of functions such as driver management and Fuel management. Inshort the thesis encompasses four sections:1.Survey of the general contractor industry: The survey has been preformed toevaluate the potential size of the market for fleet management services in the generalcontractor industry.2.Needs analysis: The needs analysis aim was to define what contractors tasks andgoals are, and to determine what functions they want and need from a system.3.The use of CAN and the technical premises: The prerequisite for developing asophisticated and generic system is that vehicle data can be accessed from the CANbuss.The use of CAN standards in construction equipment has therefore beenexamined.4.Specification: An explicit set of requirements have been set to be satisfied by a Fuelmanagement service, based on CAN standard protocol J1939.Important conclusions: The use of CAN protocol standards are extensive and the prerequisitesfor developing elementary and CAN based services good. The services should be compatiblewith different manufacture?smachines.

Overdue cleanings have for a long time been an important topic of discussion within the forestry sector. When stands that have not been pre-commercially thinned are reaching the level of commercial thinning, many problems occur in terms of decision-making and economical outcomes. These types of stands are commonly known as conflict-stands. The work was carried out partly as an interview survey towards representatives from the forest sector and the energy sector, partly as a case study of conflict-stands situated in Böksholm, north of Växjö and in Tönnersjö east of Halmstad. The criteria for the studied stands were that they had to be dominated by Norway spruce and be in a severe status of ?conflict?. The aim of the interview was to get an overview of the situation today, and also analyse trends in terms of conflict stands.

As emission legislations across the world continuously pushes engine development forward,engineers constantly need to come up with and implement Fuel saving technologies. During thelast decade, variable cam phasing has become a popular solution to increase gas exchangeefficiency. This configuration is typically mechanically constrained by camshaft limitations, anda solution to circumvent this problem would be to use a different valve actuation principle.One example of this is to use pressurized air controlled by electrical solenoids. Such a systemhas been developed byCargine Engineering and this provides the starting point for this work. Tobe able to operate the valvetrain on an actual engine, a control system is needed.

There have been changes in Earth?s climate system on both global and regional scale since the pre-industrial era and some of these changes are due to human activities such as the combustion of fossil Fuels. This calls for the development of engines with a higher efficiency and less harmful emissions. One interesting concept is the Homogeneous Charge Compression Ignition (HCCI) engine, which has the advantages of potentially low emissions combined with high efficiency. However, HCCI with diesel Fuel requires a relatively long Fuel/air mixing time to ensure a "homogenous" charge.

Future emission legislation puts great emphasis on increasing the efficiency of the engine, thereby reducing Fuel consumption. The tribological contact between cylinder liner and piston ring is where an great amount of energy is lost due to friction, and by reducing these losses an reduction in Fuel consumption can be achieved.The aim of this thesis was to evaluate the tested piston ring coatings against a plasma sprayed cylinder liner and rank these combinations of materials for friction and wear resistance. The coatings that were tested was Cr + Al2O3, (Al,Cr)N, two types of CrN and WC / C.The experimental tests were performed with a so-called pin-plate, where used oil with addition of an acidic mixture of sulfuric and nitric acid to mimic the acidic condensate formed when exhausts recirculate, were added with a continuous flow. The results were then analyzed by weighing, studies by optical microscopy and scanning electron microscopy (SEM) and profile measurements.The results from each material combination were that the plasma coated cylinder liner wears too aggressively in order to yield a ranking of the piston ring coatings based on the parameters of friction and wear resistance. It is therefore proposed that an alternative coating on the cylinder liner should be developed, lacking the large abrasive wear on piston rings and that can withstand the corrosive environment resulting in engines equipped with EGR.

The purpose of this study has been to make an inventory of combustible waste in the region around Norrköping and to investigate the composition of domestic waste, industrial waste and two different types of sludge. The work was performed at the request of Norrköping Miljö & Energi, due to the planning of an incineration plant. The inventory of the waste was performed through inspection of environmental impact reports, from waste disposal plants in a number of local government areas in the region. The quantities were also compared to another inventory, carried out in a different way. The characterisation of the wastes was compared to the Fuel specification determined by Norrköping Miljö & Energi.

Uppsala County has ambitious environmental aims for the planned residential area inÖstra Sala backe. In this thesis different energy sources have been evaluated todetermine which system that would be most favorable given currently availableinformation about the project. Planned energy usage has been divided into tap waterheating, space heating and power. Three base case scenarios were made with districtheating, small scale bio Fuel and heat pump. Solar power and solar heating were thensimulated and the production from the two could individually be deducted from theenergy need in the base cases, constituting 9 different scenarios.

Buildings worldwide account for 40 % of the total energy use. Climate change is of increasing importance, but few are willing to reduce their standard of living or get a higher cost for the change. Energy efficiency of existing buildings gives the greatest benefit economically and environmentally. The real estate company Klövern AB manages 46 properties in Karlstad. Heating is the major cost of the total operating costs of real estate. Rising energy prices increase the need for Klövern AB to improve energy efficiency and to investigate alternative sources of heat.

Biogas is increasingly used for Fuel in for example vehicles and it´s produced in a biogas processconsisting of the steps of pretreatment, digestion and gas cleaning. The pretreatment is a method usedto increase the gas production and / or destroy pathogens. The digestion is the stage when anaerobicmicroorganisms convert bio-mass of a substrate to a raw gas containing about 65% of methane. Thegas cleaning is used to increase the methane content to about 97% so the gas can be used for motors invehicles. The biogas part of the Ekeby sewage plant in Eskilstuna is using multiple substrates.

This report summarizes the development of a calculation program estimating the profitability of converting a peak-load oil-fired boiler to pellets. To convert an oil-fired boiler to pellets a new Fuel handling system must be designed. Changes also have to be made to some other components. Since there are many different techniques for transportation, storage and treatment of the Fuel only the most interesting techniques from Swecos experience and interest were included in the study.The capacity of the different parts in the system was dimensioned based on the power of the boiler after conversion. To estimate prices, installed power and dimensions manufacturers and distributers were contacted.

Future emission legislation puts great emphasis on increasing the efficiency of the engine, thereby reducing Fuel consumption. The tribological contact between cylinder liner and piston ring is where an great amount of energy is lost due to friction, and by reducing these losses an reduction in Fuel consumption can be achieved.The aim of this thesis was to evaluate the tested piston ring coatings against a plasma sprayed cylinder liner and rank these combinations of materials for friction and wear resistance. The coatings that were tested was Cr + Al2O3, (Al,Cr)N, two types of CrN and WC / C.The experimental tests were performed with a so-called pin-plate, where used oil with addition of an acidic mixture of sulfuric and nitric acid to mimic the acidic condensate formed when exhausts recirculate, were added with a continuous flow. The results were then analyzed by weighing, studies by optical microscopy and scanning electron microscopy (SEM) and profile measurements.The results from each material combination were that the plasma coated cylinder liner wears too aggressively in order to yield a ranking of the piston ring coatings based on the parameters of friction and wear resistance. It is therefore proposed that an alternative coating on the cylinder liner should be developed, lacking the large abrasive wear on piston rings and that can withstand the corrosive environment resulting in engines equipped with EGR.

Swedish energy policy aims to increase the use of energy from renewable sources and this should be done in a safe, environmentally and sustainable manner. According to the Energy Agency the use bio-Fuel increased by 73% between 1990 - 2006. Stands with high share of slash are often located on areas with high productivity which often are located on soils with poor bearing capacity. This will increase traffic on susceptible soil leading to increased ground damage. To reduce the risk of ground damage at slash-forwarding, ground protection is needed.

Swedish energy policy aims to increase the use of energy from renewable sources and this should be done in a safe, environmentally and sustainable manner. According to the Energy Agency the use bio-Fuel increased by 73% between 1990 - 2006. Stands with high share of slash are often located on areas with high productivity which often are located on soils with poor bearing capacity. This will increase traffic on susceptible soil leading to increased ground damage. To reduce the risk of ground damage at slash-forwarding, ground protection is needed.

Fuel produced from renewable resources is of big interest. In this project the difference between a few different renewable materials are compared on the matter of environmental load when ethanol is produced. The renewable materials that are compared are Salix, straw and reed canary-grass (rörflen). The cellulose in the material is cut down to small pieces and then hydrolysed so that the sugar from the cellulose can be fermented into ethanol. Tha amount of ethanols that is studied in this work is the smount of ethanol needed to cultivate 1000 ha. The functional unit in the report is 1000 ha.

The demand for district heating is expected to decrease in the future, due to competition from heat pumps and energy efficiency measures in buildings. Development of existing district heating systems is therefore necessary for district heating companies to maintain market shares. This Master?s thesis describes and investigates the heat and electricity production and profitability of a combined Organic Rankine Cycle (ORC) and heat pump that is integrated with an existing district heating system. The studied district heating system is utilizing heat from waste incineration. In Sweden waste constitute 20 % of the Fuel mix used in district heating systems, and this share is expected to increase in the future.