Storage of biomass is often associated with problems such as heat development, dry matter losses and reduction of Fuel quality. The rise in temperature can potentially cause a risk of self-ignition in the Fuel storage. Moreover, emissions from storage piles can cause health problems in the surrounding. The dry matter losses and reduction of Fuel quality can have economical effects. The aim of this thesis project is to develop guidelines on how to store large amount of biomass at Vattenfalls heat and power plants in an optimal way.

The objective of this M. Eng. Diploma work was to validate the new version, CASMO-5M, and compare the results with CASMO-4E, by using the same input in both programs. The tasks that were included in this work was to compare TIP-measures, k-effective curves (warm), k-effective curves (cold), the effect of void on k-effective, the isothermal temperature coefficient (ITC), the moderator temperature coefficient (MTC), damping ratio calculations, internal effect in a Fuel bundle of a BA-rod, the speed of BA-out burn, impact of xenon, falling control rod, margins and isotopes.The TIP-measures showed that the differences were small for all reactors, at most, 6% nodal improvement by C5M (Casmo-5M) for Oskarshamn 3. The warm measurements of k-effective showed that C5M had a higher value for all cycles of Oskarshamn 1, 2 and 3 in comparison to C4E (Casmo-4E).

All products will eventually end up as waste, which in a sustainable society has to be handled in an efficient and environment friendly way. This report focuses on waste fractions meant for combustion, often difficult to characterize. However, more homogeneous fractions that are treated biologically are also discussed.The study concerns the region of Borås, Sweden, where the waste plant Sobacken has provided a good starting point. On this site, Fuel to the Energy-from-Waste plant of Borås Energi is prepared and the biological waste is treated through anaerobic digestion.One important part of the study has been to collect experience-based knowledge from the technical staff at Sobacken and Borås Energi. This information was compiled into an overview of wanted and unwanted fractions to the preparation plant and the boilers respectively.

The aim of this study was to develop a simple model for calculating stock costs for bio Fuel at Billerud Karlsborg and subsequently recommending a suitable stock level of bio Fuel. The stock components considered in the model are GROT (branches and tops), bark, dry wood chips, raw wood chips from barking and sawdust. The calculations are based on a probability distribution of historical deviations between ordered and delivered volumes. The model presents two different ways to manage the supply in case of irregular deliveries. The first way is to stock enough volume to cover the deviations and the second way is to compensate with a quick purchase from the spot market (at extra high purchase prices).

This report was written as a final thesis within the Department of forest economics at the Swedish University of Agricultural Sciences as a completion of the M.SC Forestry programme. The aim of this study was to create a model that, with respect to given stock levels, temperature, Fuel usage and Fuel price, would identify the optimal levels for purchase of bio Fuels, optimal levels of incineration of bio Fuels and the sum of the present values of all costs. The model would be applicable for a larger district heating plant. Data regarding temperature were received from SMHI. Information considering Fuel prices was taken from the Swedish Forest Agency and the facts about Fuel usage were collected from a large district heating plant, located in the southwest of Sweden. For the temperature, a sinus curve was adapted to describe the temperature over a year.

Recent turmoil surrounding nuclear power as an energy source, especially since the accidentat Fukushima, has largely contributed to the debate of whether or not nuclear power should beused as an energy source. This study has examined the economic feasibility of replacingForsmark?s 3rd nuclear reactor with a bio Fueled power plant, and find out how this could bedone.The power generation that has to be replaced is equal to 1170 MWe. To replace this, 6 largescaleCFB-boilers, each providing over 200 MWe, were necessary. In addition to this, eachboiler required their respective turbine sets, comprising one high-pressure-, and one lowpressureturbine with intermediate reheating capacities.Based on this, a rankine-cycle was modeled using the software EES, to be able to calculatethe total heat required in the power plant.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

Biogas is a renewable Fuel that can be extracted from anaerobic digestion of many differentsubstrates, for example biological household waste. An alternative handling of the waste is tomix it with other wastes and incinerate it in a combined heat and power (CHP) plant. Thisstudy uses life cycle assessment to investigate which type of waste handling that is betterfrom an environmental point of view, anaerobic digestion with biogas production orincineration. The results are based on a case study of a biogas production plant owned by thecompany Ragn-Sells in Vänersborg. The alternative is incineration at a CHP plant inGothenburg.

AbstractThis report is made in cooperation with the municipality of Vasteras and technical committeestaff. The report addresses several topics that affect Fuel stations in Vasteras. The reportcontains two parts, first is a inventory that review all stations in the area to be addressed. Theinventory is made with consideration to various things that geographic situation, whatcompanies are represented and what level of service stations have. And the second part of thereport, is done with the analysis of how it looks in daily situations review.

The main aim of this study was to investigate and compare different methods for the extraction of forest Fuel from environments close to an archipelago. The study was based on relevant literature and published reports as well as personal communications. Forestry has traditionally been characterized by intense efforts to rationalize and mechanize the cutting technique used for timber and pulpwood. In line with the increasing importance of forestry, more concentrated efforts can be expected in the area of techniques and methods, especially for the above-mentioned product lines. In Sweden, forestry is of major importance and the Swedish economy and standard of living have mainly been created based on the revenues generated from it. Thus, it is vital that Swedish forests are harvested in an efficient and responsible manner. The demand for bioFuel is growing and today accounts for 15% of total Swedish energy production, a share that will probably increase. This study is based on three research questions, which are described under the heading of Aim. The results reveal that the most profitable method for handling forest Fuel is the traditional one, which is also the most commonly used method in southern Sweden, namely the stockpiling of logs in a clearing by means of forwarders followed by splintering at the place from where they will be distributed. Today, the high cost of barge transport required for the extraction of forest Fuel in an archipelago environment renders such operations unprofitable.

To achieve the requirements to decrease emissions of greenhouse gases by 20 % by 2020, Swedenneeds to increase its use of bioenergy. In doing so it seems natural that those who already haveaccess to large amounts of bioFuels in the form of by-products such as straw, wood chips anddigestible materials take advantage of these assets locally. By combining production of heat withpower production at the farm it may be possible to not only reduce the direct use of fossil Fuel forheating but also reduce energy costs.The purpose was to simulate different cases of using a small scale bioFueled combined heat andpower plant for farm-based systems. A MatLab-model was developed and used to draw conclusionsabout the costs for production of heat and electricity with different conversion technologies.The model uses climate data to simulate the variations in heat energy demand on a day-to-day basis.The given heat demand is the base of the simulation and from this the possible electric output iscalculated. This study has focused on the impact of the following properties: electric-, heat- andtotal efficiency, Fuel, Fuel price and specific Fuel requirements.

Humidity problems and poor ventilation are factors that we associate with poor indoor airquality which are known to negatively affect health. Such problems have decreased with timein Sweden but, in other countries this is still a major problem especially during winter. InChile, this is most common in the central regions of the country, especially the Strait ofMagellan. This issue is primarily due to surface condensation happening indoors which bringsabout dampness which facilitates the growth of fungus and stains, foul odors, metal corrosionand more. This is due to a combination of poor ventilation and insufficient forms of heatingalong with buildings which have no insulation.

A new type of device for measuring thev m& ?rate of Fuel sprays from a diesel Fuel injector has been developed and the various steps in the development are described. The device works by deflecting all of the sprays from the injector at the same time by using a bell shaped deflector. A load cell consisting of a machined steel part with strain gauges mounted on it measures the resulting force. The shape of the curvature in the deflector bell shape has been evaluated by photographing the flow in a 2D?version of the curve shape.

Summary Today energy prices are rising. As a result biomass Fuel is getting more and more interesting. Wood chips is very popular, but also straw from grain production is on the table. Lunds Energi AB project a combined power and heating plant in Örtofta out of Lund. Wood chips is meant to be the main energy source, complemented by straw. In this thesis the transportation of straw for Fuel is studied.

AbstractThis report is made in cooperation with the municipality of Vasteras and technical committeestaff. The report addresses several topics that affect Fuel stations in Vasteras. The reportcontains two parts, first is a inventory that review all stations in the area to be addressed. Theinventory is made with consideration to various things that geographic situation, whatcompanies are represented and what level of service stations have. And the second part of thereport, is done with the analysis of how it looks in daily situations review.