Future emission legislation puts great emphasis on increasing the efficiency of the engine, thereby reducing fuel consumption. The tribological contact between cylinder liner and piston ring is where an great amount of energy is lost due to friction, and by reducing these losses an reduction in fuel consumption can be achieved.The aim of this thesis was to evaluate the tested piston ring coatings against a plasma sprayed cylinder liner and rank these combinations of materials for friction and wear resistance. The coatings that were tested was Cr + Al2O3, (Al,Cr)N, two types of CrN and WC / C.The experimental tests were performed with a so-called pin-plate, where used oil with addition of an acidic mixture of sulfuric and nitric acid to mimic the acidic condensate formed when exhausts recirculate, were added with a continuous flow. The results were then analyzed by weighing, studies by optical microscopy and scanning electron microscopy (SEM) and profile measurements.The results from each material combination were that the plasma coated cylinder liner wears too aggressively in order to yield a ranking of the piston ring coatings based on the parameters of friction and wear resistance. It is therefore proposed that an alternative coating on the cylinder liner should be developed, lacking the large abrasive wear on piston rings and that can withstand the corrosive environment resulting in engines equipped with EGR.

The purpose of this study has been to make an inventory of combustible waste in the region around Norrköping and to investigate the composition of domestic waste, industrial waste and two different types of sludge. The work was performed at the request of Norrköping Miljö & Energi, due to the planning of an incineration plant. The inventory of the waste was performed through inspection of environmental impact reports, from waste disposal plants in a number of local government areas in the region. The quantities were also compared to another inventory, carried out in a different way. The characterisation of the wastes was compared to the fuel specification determined by Norrköping Miljö & Energi.

Uppsala County has ambitious environmental aims for the planned residential area inÖstra Sala backe. In this thesis different energy sources have been evaluated todetermine which system that would be most favorable given currently availableinformation about the project. Planned energy usage has been divided into tap waterheating, space heating and power. Three base case scenarios were made with districtheating, small scale bio fuel and heat pump. Solar power and solar heating were thensimulated and the production from the two could individually be deducted from theenergy need in the base cases, constituting 9 different scenarios.

Buildings worldwide account for 40 % of the total energy use. Climate change is of increasing importance, but few are willing to reduce their standard of living or get a higher cost for the change. Energy efficiency of existing buildings gives the greatest benefit economically and environmentally. The real estate company Klövern AB manages 46 properties in Karlstad. Heating is the major cost of the total operating costs of real estate. Rising energy prices increase the need for Klövern AB to improve energy efficiency and to investigate alternative sources of heat.

Safety and risk management currently have a starting point based on the negative outcome of safety, thus the lack of safety. The starting point for the thesis is to find a way to measure the positive outcome of safety through ergonomic aspects regarding chemical plants that are covered of the Seveso II Directive.Through a literature study of safety and ergonomics fourteen key aspects of safety were found. Safety Performance Indicators (SPI's) are used to assess the fourteen identified proactive indicators of safety. An analysis in three steps - called risk status assessment - is design to give an SPI its value. A pilot study of the risk status assessment was performed at the ethanol producer Lantmännen Agroetanol in Norrköping, Sweden..

Biogas is increasingly used for fuel in for example vehicles and it´s produced in a biogas processconsisting of the steps of pretreatment, digestion and gas cleaning. The pretreatment is a method usedto increase the gas production and / or destroy pathogens. The digestion is the stage when anaerobicmicroorganisms convert bio-mass of a substrate to a raw gas containing about 65% of methane. Thegas cleaning is used to increase the methane content to about 97% so the gas can be used for motors invehicles. The biogas part of the Ekeby sewage plant in Eskilstuna is using multiple substrates.

This report summarizes the development of a calculation program estimating the profitability of converting a peak-load oil-fired boiler to pellets. To convert an oil-fired boiler to pellets a new fuel handling system must be designed. Changes also have to be made to some other components. Since there are many different techniques for transportation, storage and treatment of the fuel only the most interesting techniques from Swecos experience and interest were included in the study.The capacity of the different parts in the system was dimensioned based on the power of the boiler after conversion. To estimate prices, installed power and dimensions manufacturers and distributers were contacted.

Future emission legislation puts great emphasis on increasing the efficiency of the engine, thereby reducing fuel consumption. The tribological contact between cylinder liner and piston ring is where an great amount of energy is lost due to friction, and by reducing these losses an reduction in fuel consumption can be achieved.The aim of this thesis was to evaluate the tested piston ring coatings against a plasma sprayed cylinder liner and rank these combinations of materials for friction and wear resistance. The coatings that were tested was Cr + Al2O3, (Al,Cr)N, two types of CrN and WC / C.The experimental tests were performed with a so-called pin-plate, where used oil with addition of an acidic mixture of sulfuric and nitric acid to mimic the acidic condensate formed when exhausts recirculate, were added with a continuous flow. The results were then analyzed by weighing, studies by optical microscopy and scanning electron microscopy (SEM) and profile measurements.The results from each material combination were that the plasma coated cylinder liner wears too aggressively in order to yield a ranking of the piston ring coatings based on the parameters of friction and wear resistance. It is therefore proposed that an alternative coating on the cylinder liner should be developed, lacking the large abrasive wear on piston rings and that can withstand the corrosive environment resulting in engines equipped with EGR.

Sahlgrenska Academyat University of GothenburgDepartment of Internal Medicine and Clinical NutritionAbstractTitle: Alcohol consumption after training and its effects on muscle gain and recovery adult menAuthor: Frida Carlstedt, Puck JanssonSupervisor: Frode SlindeExaminer: Anna WinkvistProgramme: Dietician study programme, 180/240 ECTSType of paper: Examination paper, 15 hpDate: April 09, 2014Background: Today, the Swedish population exceeds the recommendations for alcohol intake while advised to move at least thirty minutes a day. It is well established what happens if you drink alcohol before a workout or if you workout the day after an alcohol intake, but it is less well established how muscle gain and recovery are affected by an intake of alcohol in the phase of recovery.Objective: The objective of this review is to investigate if there is a relation between alcohol intake after a workout and effected recovery and muscle gain. This was performed by measuring the outcomes cortisol, testosterone, creatine kinase as well as different measures of muscle strength. The issue was ?Does an intake of alcohol after training affect recovery and muscle gain??Search strategy: A systematic review in the databases PubMed and Scopus with the MeSH-terms: exercise, muscles, recovery of function, training, athletic performance, performance, sport, alcohol drinking, alcohols, alcohol and ethanol.Selection criteria: Criteria for articles to be included in this review were that they would be RCT- and human studies in healthy subjects as well as containing an ethanol intake after a physical activity that consisted of weight training in the form of resistance training or other forms of activity that promotes strength.Data collection and analysis: A systematic search for literature as mentioned above (search strategy) was performed as well as an analysis with the SBU quality review template for randomized studies, and a quality review for each measure of outcome according to Gothenburg University summarized evidence template for measures of outcome.4Main results: Many studies are authored by the same group of researchers and/or are of a lower quality.

Swedish energy policy aims to increase the use of energy from renewable sources and this should be done in a safe, environmentally and sustainable manner. According to the Energy Agency the use bio-fuel increased by 73% between 1990 - 2006. Stands with high share of slash are often located on areas with high productivity which often are located on soils with poor bearing capacity. This will increase traffic on susceptible soil leading to increased ground damage. To reduce the risk of ground damage at slash-forwarding, ground protection is needed.

Swedish energy policy aims to increase the use of energy from renewable sources and this should be done in a safe, environmentally and sustainable manner. According to the Energy Agency the use bio-fuel increased by 73% between 1990 - 2006. Stands with high share of slash are often located on areas with high productivity which often are located on soils with poor bearing capacity. This will increase traffic on susceptible soil leading to increased ground damage. To reduce the risk of ground damage at slash-forwarding, ground protection is needed.

The demand for district heating is expected to decrease in the future, due to competition from heat pumps and energy efficiency measures in buildings. Development of existing district heating systems is therefore necessary for district heating companies to maintain market shares. This Master?s thesis describes and investigates the heat and electricity production and profitability of a combined Organic Rankine Cycle (ORC) and heat pump that is integrated with an existing district heating system. The studied district heating system is utilizing heat from waste incineration. In Sweden waste constitute 20 % of the fuel mix used in district heating systems, and this share is expected to increase in the future.

Waste appears to be a low-cost fuel compared to biofuel. This Masters thesis was conducted for Vattenfall Utveckling AB and deals with how waste in the fuel affects the performance of a SCR-catalyst. Different mechanisms of deactivation were surveyed, focusing on the poisoning mechanism. A literature study was carried out, which was used as a reference when analysing the results.Small samples (9x2x2 cm, 64 pieces) cut out from a full-scale unused honeycomb catalyst were exposed up to 1500h in two different combustion plants, Johannes in Gävle (co-combustion) and Högdalen in Stockholm (waste-combustion). The activity was measured mainly at 300°C but also at 250, 350, 375 and 400°C.

The thesis was performed at Forsmarks Kraftgrupp AB in the department ofmechanical engineering, FTCM. Forsmark nuclear power plant has had problems with cracks in some of the controlrods which are placed in the reactor at Forsmark 3. To investigate the cause of this,material samples were taken from five of the damaged control rods. This sampling ofthe rods resulted too short rods to be transported in the shipping container to theinterim storage facility for used nuclear fuel in Oskarshamn. Control rods are crucial components in a nuclear reactor, regulating the reactoreffect by blocking or unblocking fuel rods. Control rods which have been in thereactor are always handled under water in order to protect against the radiation theyemit. The task was to design a control rod adapter that extends the control rod sotransport can be performed from Forsmark. The goal of the work was a complete setof blueprints so the control rod adapter can be manufactured and mounted on theshort control rods and then be transported to the interim storage facility. The work began with mapping of how control rods normally being handled from thereactor to the interim storage facility.

This thesis aims to examine the viability of various techniques for increased electricity generation in CHP plants and the effect of electricity price fluctuations on the profitability.The techniques examined are fuel dryer, pellet production, methane production, combined methane- and pellet production, seasonal heating storages in caverns and pit heat storages and condensing tail. Using Excel and Matlab, the prerequisites for investment costs, revenues and expenses were calculated.What affects the price of electricity is a combination of economic and technological development, energy prices, economic structure, population changes and weather. Different scenarios for the electricity price were therefore examined. In the base case, the electricity price was given by the Nord Pool electricity price statistics of area three in 2011. Thereafter, WiMo was used to design the electricity scenarios for 2030, which was then applied to the data to obtain the viability of various scenarios. The techniques examined were found to give greater profits to the CHP plant by increasing and optimizing the production of electricity.