Swedish energy policy aims to increase the use of energy from renewable sources and this should be done in a safe, environmentally and sustainable manner. According to the Energy Agency the use bio-fuel increased by 73% between 1990 - 2006. Stands with high share of slash are often located on areas with high productivity which often are located on soils with poor bearing capacity. This will increase traffic on susceptible soil leading to increased ground damage. To reduce the risk of ground damage at slash-forwarding, ground protection is needed.

Fuel produced from renewable resources is of big interest. In this project the difference between a few different renewable materials are compared on the matter of environmental load when ethanol is produced. The renewable materials that are compared are Salix, straw and reed canary-grass (rörflen). The cellulose in the material is cut down to small pieces and then hydrolysed so that the sugar from the cellulose can be fermented into ethanol. Tha amount of ethanols that is studied in this work is the smount of ethanol needed to cultivate 1000 ha. The functional unit in the report is 1000 ha.

The demand for district heating is expected to decrease in the future, due to competition from heat pumps and energy efficiency measures in buildings. Development of existing district heating systems is therefore necessary for district heating companies to maintain market shares. This Master?s thesis describes and investigates the heat and electricity production and profitability of a combined Organic Rankine Cycle (ORC) and heat pump that is integrated with an existing district heating system. The studied district heating system is utilizing heat from waste incineration. In Sweden waste constitute 20 % of the fuel mix used in district heating systems, and this share is expected to increase in the future.

Waste appears to be a low-cost fuel compared to biofuel. This Masters thesis was conducted for Vattenfall Utveckling AB and deals with how waste in the fuel affects the performance of a SCR-catalyst. Different mechanisms of deactivation were surveyed, focusing on the poisoning mechanism. A literature study was carried out, which was used as a reference when analysing the results.Small samples (9x2x2 cm, 64 pieces) cut out from a full-scale unused honeycomb catalyst were exposed up to 1500h in two different combustion plants, Johannes in Gävle (co-combustion) and Högdalen in Stockholm (waste-combustion). The activity was measured mainly at 300°C but also at 250, 350, 375 and 400°C.

The thesis was performed at Forsmarks Kraftgrupp AB in the department ofmechanical engineering, FTCM. Forsmark nuclear power plant has had problems with cracks in some of the controlrods which are placed in the reactor at Forsmark 3. To investigate the cause of this,material samples were taken from five of the damaged control rods. This sampling ofthe rods resulted too short rods to be transported in the shipping container to theinterim storage facility for used nuclear fuel in Oskarshamn. Control rods are crucial components in a nuclear reactor, regulating the reactoreffect by blocking or unblocking fuel rods. Control rods which have been in thereactor are always handled under water in order to protect against the radiation theyemit. The task was to design a control rod adapter that extends the control rod sotransport can be performed from Forsmark. The goal of the work was a complete setof blueprints so the control rod adapter can be manufactured and mounted on theshort control rods and then be transported to the interim storage facility. The work began with mapping of how control rods normally being handled from thereactor to the interim storage facility.

This thesis aims to examine the viability of various techniques for increased electricity generation in CHP plants and the effect of electricity price fluctuations on the profitability.The techniques examined are fuel dryer, pellet production, methane production, combined methane- and pellet production, seasonal heating storages in caverns and pit heat storages and condensing tail. Using Excel and Matlab, the prerequisites for investment costs, revenues and expenses were calculated.What affects the price of electricity is a combination of economic and technological development, energy prices, economic structure, population changes and weather. Different scenarios for the electricity price were therefore examined. In the base case, the electricity price was given by the Nord Pool electricity price statistics of area three in 2011. Thereafter, WiMo was used to design the electricity scenarios for 2030, which was then applied to the data to obtain the viability of various scenarios. The techniques examined were found to give greater profits to the CHP plant by increasing and optimizing the production of electricity.

The jetengines of today are growing in complexity. Reliability for aircraft engines are of extreme importance, mainly due to safety reasons but also economical ones. This master thesis deals with faultdiagnosis in the turbine section of RM12, the engine used in Saab/BAe's Gripen. Three different faults which can occur in the turbine section was studied. These faults are: clogged fuel nozzle, hole in outlet guide vane and sensor fault.

The increasing oil prices during the last years have made it profitable to use cereal grains as a fuel. When compared with wood, cereals contain higher amounts of Cl, S and ash. The Cl and S content makes the gases from cereal combustion more corrosive than gases from wood combustion. The goal of this master thesis was to find out the variation of Cl, S and ash content for oat grain grown under different conditions. Oats was chosen because in Sweden it's considered as the cereal with the best fuel qualities.

Uppsala County has ambitious environmental aims for the planned residential area inÖstra Sala backe. In this thesis different energy sources have been evaluated todetermine which system that would be most favorable given currently availableinformation about the project. Planned energy usage has been divided into tap waterheating, space heating and power. Three base case scenarios were made with districtheating, small scale bio fuel and heat pump. Solar power and solar heating were thensimulated and the production from the two could individually be deducted from theenergy need in the base cases, constituting 9 different scenarios.

Approximately 60 million cubic meters of round wood are transported every year with trucks in Sweden and stand for 15 % of all truck transportation in the country. The big amount that is transported results in many haulage companies works in different parts of the country with different conditions to get a good flow on their transports. Today the transport pricing is very general and the payment consists of the unit round wood they are transporting and the distance of the transport. The purpose of this study were, from the freighter and the haulage company?s perspective, try to find ways to change the today applied transport pricing to more differentiated and compare them to historic payment of transportation.

Acrylamide (AM) is a commonly used monomer in the manufacture of polyacrylamide. In addition, AM has been found in heated foods that are rich in starch. The main dietary sources in Sweden tend to be crisps, French fries, fried potatoes, crisp bread, cookies and coffee. Un-fortunately, dietary intake of AM has in several studies been shown to cause cancer in ro-dents. Consequently, the compound is currently regarded as a potential carcinogen in hu-mans.

Alstom Power i Växjö arbetar med utveckling och försäljning av bland annat elektrofilter tillrökgasreningssystem vid olika typer av miljövårdsanläggningar för t.ex. kraftverksindustrin.Dessa elektrofilter kontrolleras och regleras med hjälp av styrutrustning uppbyggd av ettantal styrenheter som idag kommunicerar via en egentillverkad standard kallad ?Fläktbuss?. Föratt övervaka detta system vill man använda handburna PDA och kommunicera med Fläktbussenvia USB. För att få kommunikationen mellan USB och Fläktbuss att fungera krävs någon form avaktiv konvertering.Detta examensarbete kommer att ta upp så väl problematik och lösningar kring detproblem som finns i samband med denna konvertering..

This report describes the manufacture and control of a flying platform. The report describes the basic and fundamental theories required to get the platform flying. It touches on subjects such as A/D-conversion. PWM-control and PID-control. The sensors used in the platform are a gyro and an accelerometer.

Volvo Construction Equipment is one of the worlds largest manufacturer of heavymachinery. In Braås, Sweden, they develop and manufacture articulated haulers inseveral sizes. The biggest, the A40, is capable of loading almost 40 metric tonnes.These haulers have a bogie to distribute the forces of the load evenly onto the two axlesand there wheels. The bogie is constructed using a rigid balance beam on each side ofthe frame connecting the axles or an independent solution using hydropneumatics.An analysis has been made in order to establish the forces created during corneringand through the theory, an estimation of the extensive tyre wear and extra fuelconsumption has been made. All due to the effects of the tyres not being inline with thecornering radius.

This thesis work has been performed at the department of diagnosis and dependability at Volvo Car Company, Torslanda. The background of this project is based on interest in ascertaining how different factors possibly can affect a diagnosis method, which has been developed to find leaks in the fuel tank and evaporation system. According to the OBD II requirements leaks with an orifice diameter larger or equal to 0,5 mm, must be detected. The idea of the diagnosis method is to create an over pressure in the system with an air-pump. The current through the pump is measured and correlates to the power consumed by the pump.