Uppsatsen har undersökt hur ett antal textbaserade utbildningsmaterial avsedda för utbildning inom företagsvärlden utformas i förhållande till olika sätt att förstå och tolka innehåll. De teorier som används som utgångspunkt i undersökningen har varit Howard Gardners inlärningsteori om multipla intelligenser, samt Stuart Halls kommunikationsteori Encoding/decoding. Undersökningen har omfattat tre utbildningsmaterial som används vid Södra Cell Mönsterås som tillverkar pappersmassa, där jag undersökt en teoribok avsedd för utbildning av truckförare, en internhandbok i grundläggande datakunskap samt ett textmaterial avsett för att öka personalens kunskap om hur produktionen av pappersmassa går till. Undersökningen har gjorts i form av fallstudier där varje utbildningsmaterial har blivit ett separat fall. Analysen av materialen har genomförts i form av en riktad innehållsanalys baserad på Gardners multipla intelligenser, i syfte att finna svar på vilka intelligenser som var representerade i utbildningsmaterialet. Utifrån det resultat som analysen gav förde jag ett hermeneutiskt teorietiskt resonemang med utgångspunkt i Halls teori Encodin/decoding i hur brukarna av materialet skulle kunna tolka innehållet, beroende på faktorer som förkunskaper i ämnet och kulturell/social bakgrund. Resultatet av analysen visa att endast ett fåtal intelligenser blev representerade i de olika materialen.

In the middle of Australia there is a city called Alice Springs. The city has one of the highest amounts of daily sunshine hours and sun irradiation in the world. The Australian Government runs a project called Solar Cities, and Alice Springs is one of the participators. The main part of the goal with the Solar Cities project is to increase the amount of electricity generated by solar power and by doing that lower the impact on the environment. This thesis examines the possibilities for construction of a large scale solar power plant in Alice Springs. This is done to determine the potential of creating a more sustainable energy system in the city.

The Swedish road transport sector relies almost completely on fossil fuels. In 2007, as much as 96 percent of the total sales of fuels was made up of petrol and diesel, while at the same time the share of total emissions of greenhouse gases in Sweden that came from road transports amounted to close to 30 per cent. Sweden is by no means worse off than any other European country in these respects. In order to address the questions of high oil dependence and CO2 emissions the European Commission has proposed a reinforcement of the legislative framework, with a 10 percent minimum for the market share of biofuels in 2020. Furthermore, the proposed target is binding for the member states, unlike the current voluntary target of 5.75 percent by 2010. More than doubling the usage of biofuels in only a bit more than a decade will most likely not be possible without policy interventions.

Fuel wood is currently the third largest assortment from the forest in Sweden after pulpwood and lumber. Branches and tops i.e. logging residues are one of the assortments of fuel wood which is a common by-product after harvesting nowadays. The way to utilize, disintegrate and transport the logging residues varies between northern and southern Sweden. Branches and tops are collected throughout the year at appropriate stands, but are consumed mainly wintertime.

The first part of the thesis consists of a brief introduction to the general principles of target detection and the sensor-systems used. In the following part there is a theoretical description of the algorithms this thesis focuses on. The detection algorithms described in this paper are called Cell Average, Ordered Statistics, 2parameter and Gammadetector. Two different discriminators called Extended Fractal Features and Quadratic Gamma Discriminator are also described. The algorithms are tested on three different types of data, simulated SAR-pictures, authentic SAR-targets and IR-pictures.

This master thesis encompasses an inventory of the older industrial community of Gimo. Investigations of the contamination situation for each industrial area were done. A risk classification according to the Swedish Environmental Protection Agency?s ?Method of Surveying Contaminated Sites?, phase one, followed. The risk classification was done on areas of Iron Work, a rockwool industry and a landfill. Gimo have had iron manufacturing from 1615 until 1945. Gimo have had two blast-furnaces and two smithies periodically.

In the middle of Australia there is a city called Alice Springs. The city has one of the highest amounts of daily sunshine hours and sun irradiation in the world. The Australian Government runs a project called Solar Cities, and Alice Springs is one of the participators. The main part of the goal with the Solar Cities project is to increase the amount of electricity generated by solar power and by doing that lower the impact on the environment. This thesis examines the possibilities for construction of a large scale solar power plant in Alice Springs. This is done to determine the potential of creating a more sustainable energy system in the city.

At the beginning of 2011, Sweden started using the European rules for structural design, the Eurocodes, instead of the previous national rules. In both the previous rules and the Eurocodes, it is possible to dimension concrete columns using tabled values. However, the required cross section measurements have increased considerably. Moreover, it is possible to dimension concrete columns using calculations, however, this is unusual.The development of a fire in a fire cell can be divided into the growth stage, the fully developed fire and the cooling phase. The duration of each phase, as well as the temperature, is dependent on a number of factors, e.g.

As trucks are getting more and more advanced, information about their weight has become a key factor for controlling them in a more fuel efficient and safe manner. Knowing the mass of a heavy duty vehicle in real time has been a difficult challenge for the truck manufacturers. With the processing power for electronic control units in trucks steadily increasing, more advanced algorithms for calculating the mass has been developed, but at the moment there still is a wish for better performance.Since there is a lack of good information regarding the external forces acting on the vehicle, forces that depends on the slope of the road, foundation of the road and the wind, the methods have to be able to disregard these. Such an approach, based on an indirect least square solution, has been evaluated in this thesis. The results have been promising and based on these a recommendation about further evaluation has been made..

Tall (Pinus sylvestris L.) är ett av Sveriges viktigaste trädslag. Med ökad efterfrågan på vedråvara samt ökade krav på naturavsättningar är det viktigt att öka produktionen i skogen. Röjning och tidig gödsling ger ökad volymproduktion men kan ge icke önskvärd påverkan på vedegenskaper som ökad mikrofibrillvinkel (MFV). MFV är vinkeln mellan mikrofibrillerna i cellväggens S2-lager och cellens längdaxel och påverkas av ståndort samt konkurrensen om ljus och näringsämnen. Höga MFV resulterar i sämre kvalitet på papper och sågade trävaror.

Namibia, southern Africa, suffers from an energy shortage and is therefore facing severalchallenging problems. The use of firewood as fuel for cooking is common in the whole countryand has negative consequences for health and the environment. This work have focused ondeveloping a solar baking oven, calledSunbaker, adapted for Namibian families needs forbaking. The development was based on classic solar cooking limitations, specific needs forNamibia and to have a feasible manufacturability.The project started with a theoretical study in Sweden where different solar cookers, informationregarding Namibia, technical aspects and end user aspects were studied. To assess the need for asolar baking oven aMinor Field Study took place in Namibia during eight weeks in July toSeptember 2009 and resulted in a product design specification.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

Fortum har i samarbete med Stockholms stad presenterat en gemensam vision för att göra Stockholm till en av världens främsta miljöbilsstäder till 2030. Ett viktigt led i detta mål är introduktionen av nya elfordon innehållande litium?jontekniken på den svenska bilmarknaden. Då det befintliga regelverket angående laddning av ackumulatorer i fordon inte nämner den nya tekniken har frågeställningen kring luckor i lagstiftningen lyfts fram av Fortum. Det övergripande syftet med studien har varit att undersöka risker och regelverk kring laddning av elbilar innehållande litium?jonackumulatorer.

In the thesis we have shown that it is possible with current technology, to buildneighborhoods that are largely self-sufficient. We have obtained some information aboutongoing work in the field of energy efficient buildings and active house which we have usedto develop a model. The feasibility study for Ranagård we have e.g been forced tofollow laws on groundwater covered, resulting in the construction of basements for singlefamilyhome is not possible. The model that we have built up overtime has been the central part of the work. The model illustrates very well what an activehouse neighborhood means and potential of such an area.

Using the Introductory Carbon Balance Model, ICBM, five different crop rotations with rye 1. Rye-Ley-Ley-Rye-Beans-Rye 2. Rye-Rye-Rapeseed-Rapeseed 3. Rye-Ley-Ley-Rye-Potatoes-Rye 4. Rye-Rye-Potatoes-Wheat 5. Rye-Rye-Potatoes-Beans-Wheat-Rye-Potatoes-Rapeseed were tested theoretically in four different cultivation scenarios ? Straw left on the field, biogas digestate added as fertilizer. Labelled ?+straw+BD?. ? Straw left on the field, only synthetic fertilizer. Labelled ?+straw-BD?. ? Straw harvested, biogas digestate added as fertilizer.