A third party access to district heating networks has been proposed in Sweden, to increase the competition on the district heating market. Such third party access could create opportunities for the agricultural sector as an energy producer. This study describes the technical, economical and environmental prerequisites for a farmer cluster to build and run a heating plant, fueled with local wood fuel. The heating plant in the described scenario is 8 MW and will supply a village of 1000 houses, and is fueled with wood chips exclusively. Supplying a heating plant with fuel puts high demands on the logistics, since there need to be a continuous flow of fuel. In the scenario, wood residues from felling and thinning is stored in stacks in the forest, and a few times a year chipped and transported to a storage area at the heating plant. In the study, an estimation of the profitability has been made by estimating the cost of the investment, personnel, operating and maintenance costs and costs for the fuel and ash handling.

Today there is a limited demand for quality certified cereal in Sweden. The demand can in the future increase and become a requirement for the entire market. Since the first of January 2005, grain producers in Sweden are food producers and traceability is important for the food industry. It is possible for grain producers to certify the productions under the certification IP SIGILL. The purpose of this essay is to explore why some grain producers continue to be certified while other producers end the IP SIGILL certification.

This report is a study made at Pallco AB. Pallco is a subcontractor that is specialized on steel and aluminium components.The aim of the report is to show an improvement proposal that leads to a reduction of the storage and improve the flow through the production of one item that is a part of a product that Pallco manufactures.With the increasing competition from other countries who can manufacture with lower costs must Swedish companies try to make theirs manufacturing as efficient as possible and remove all waste. By using the tools of Lean Production it is possible to reduce the costs and increase the efficiency.The method we used is value stream mapping. A map of the present condition has been made and then different improvement proposal were discussed. A map of a future condition has also been designed..

This study has investigated the possibilities of implementing lean in a division of a hospital in Stockholm. The goal was to reduce the lead time for the patient to get his diagnose by implementing lean in the two production flows of this division. In order to accomplish it, a complete map over the value stream has been done. With the help of the value stream map and lean theory a list over the processes in contradiction with lean has been made. Finally propositions to implement lean and by this way reduce the lead times in this stream have been made out.

The environmental assessment system Miljöbyggnad is a Swedish system initiated by Bygga-Bo-Dialogen to assess buildings with regards to three main areas; ?Energy?, ?Indoor climate? and ?Materials?. A building can obtain three different classifications depending on how well it manages to meet the demands. GOLD is the highest classification and is followed by SILVER and BRONZE. The majority of the measures needed to comply with the demands are done during the design phase.

The Swedish building contractor JMRegion Öst would like to to investigatethe possibilities of developing andstreamlining the production of singlefamilyhouses. JM are producing singlefamilyhouses with prefabricated framesat a rate of about two houses per week.During construction, the different tasksare performed by JM?s own productionstaff but also by varioussubcontractors.When examining the schedules of recentlyproduced projects, it appears that allthe houses are more or less completedeight weeks before the customer moves into the house. During those eight weeksseveral operations are conducted such asinspections, installation of appliancesand cleaning procedures. The inspectionperiod constitutes between 25 and 35% ofthe complete construction period.By conducting interviews, it has beendiscovered that this final phase is anessential security buffer for delays anderrors that often occur.

This survey was made during the summer of 2004 and the spring of 2005, on commission from the National Board of Forestry. The aim of this report was to investigate how often Norway spruce (Picea abies L. Karst), is planted on poor Scotch pine (Pinus Silvestries) sites and if it affects the yield of Norway spruce? In order to investigate this, data from 29 stands witch had a lower site index than T24 was collected. The investigated stands were situated in the southern-eastern Sweden. In 20 plots in each stand, the highest tree, age, number of seedlings, site index and tree species per stand were measured.

Successful forest regeneration is a prerequisite for sustainable forest management. Therefore, it is important to prevent browsing damage on the commercially important tree species Scots pine. In this study I have tested a new alternative way to increase the available amount of forage and increase the use of these resources by especially moose. The method is based on a slash treatment at harvest, where the accessibility of slash as forage is increased during final felling or commercial thinning by gathering the slash and putting the Scots pine slash on top of the slash piles. This study has compared the availability of forage, the amount of browsed biomass and the number of fecal pellet groups between conventional and slash treated stands after final felling and commercial thinning in southern Sweden.

This study in the subject of forest planning is made for Sveaskog and its aim is to develop tools that prognosticate outcome in terms of volumes per sort from not yet cut forest stands. The degree of detail is just to get reliable results for at least one months volumes, for Sveaskogs own forestland in the market region of Norrbotten that is about 100 000 m3fub. The course of action to accomplish this is regression analysis and the data consists of cut tracts on own forestland in Norrbotten during the years 2006, 2007 and 2008. That is a little more than 4 million m3fub. Two tools were made.

The purpose of this master?s thesis was to find problems that occur in the production line at Atlas Copco Rocktec Division, in order to decrease the costs of defect in quality. When the problems were distinguished, the authors ought to choose the problem with the highest improvement potential. One request from the constituent at Atlas Copco Rocktec Division was to connect the improvement to the document The Way We Produce. The document provides information and values about Atlas Copco and consists of 10 principles to be able to reach their vision.

The purpose of this thesis is to analyze the design and function of an engine production management?s control system and its intended function, and to contrast it with the present management control systems in use on an operational level. Interviews conducted with employees from all levels of the engine production are the main source of this study?s empirical foundation. Information has also been gathered from relevant written material such as annual reports, internal documents etc.

Bakgrund: I takt med att konsumenters preferenser har förändrats, har företag fått överge massproduktion till förmån för produktionssystem som bättre avspeglar konsumenternas ökade krav på flexibilitet. Ett sätt för att överbrygga denna utmaning är att implementera lean production. Även om detta sätt att producera på har tydliga fördelar för dagens företag, verkar lean production även kunna medföra problem i avseende på att kombinera med den befintliga, i många fall, traditionella styrningen i företaget. En del av styrningen som verkar vara speciellt svår att kombinera med implementeringen av lean production rör mätningen av produktionen. Vid en närmare granskning visar det sig att det råder vissa motsättningar mellan traditionell mätning och lean production som kan påverka företagets beslutsfattande negativt.

Induction motors, often referred to as the workhorse of the industry, play an important role in production today. Therefore, it's important to diagnose any faulty induction motor prior to failure to avoid costly and time consuming production stops.This thesis compares methods for diagnosing induction motors in operation, MCSA, Park's vector approach and the standard method used by Swedish industries today. By simulating broken rotor bars and short-circuit in one of the windings, each method is tested and the results are compared using matlab.The results need further verification due to uncertainties of the condition of the test motor, even though the experiment gives a hint of the different advantages of each method. A combination of the methods should be able to tell if the motor needs further examination..

The energy consumption in the sectors of residential and public buildings is 40 % of the total energy consumption in Sweden. The main part, 85 %, of the energy use in these sectors is for operation of the buildings. The rest is used in the building process. When energy-efficiency measures are taken the energy use during the operation time decreases and the fraction of energy consumption during the building time increases. This project is carried out in cooperation with JM AB and concerns the energy use during the building time of production of blocks of flats at the building site.The main part of the electricity that is used during the production of apartment buildings goes into the heating of portacabins and illumination of the building during the construction phase.

My aim in this case study has been to create a method for creature design to test this method in a production and evaluate the results. To achieve this I studied and analyzed the methods of three concept artists and illustrators named James Gurney, Neville Page and Iain McCaig. From the analysis of these artist´s methods, combined with my own personal experience, a new method was formed. To test this method a creature was designed based on directives given by a game design group in the process of creating a table top role playing game in a fictitious world. These directives where given for the creature´s role and its living conditions.