This Master of Science Thesis was a complement project to the PIEp study MENTOL, carried out at a Swedish midsize medical device company.. PIEp nationally works for a long-term increase of the innovation capability of people and organizations. The purpose of this study was to find measuring parameters of innovation that fit medium-sized technological companies and organizations, Another purpose was to evaluate an innovation investment at the company, consisting of external consultant?s education of key personnel in innovation, and a two day innovation seminar with all personnel at the company participating. The methods used during this Master of Science Thesis were: feasibility and literature studies about innovation and innovation measurements, quantitative and qualitative interviews, surveys and workshops.For an accurate measure of innovation it is crucial to a have full understanding of what innovation is, and clarity of the purpose of the measurement itself.

The gas turbines in the Swedish secondary reserve are reaching the end of their technical lifetime, hence alternative solutions need to be considered. One of the solutions thought to have the greatest potential is the use of so called consumptionreduction. By entering contracts with large consumers, agreements are made to reduce consumption in the event of major disturbances in the power system and thus being used as a secondary reserve. This thesis investigates the feasibility of consumption reduction as part of the secondary reserve. This has been achieved by developing a requirement specification for the disturbance reserve and by studying the technical and economic potential for consumption reduction among a range of consumers.The technical potential for consumption reduction that fulfils the requirements for participating in the secondary reserve are on average 750 MW in SE 3 and 98 MW in SE 4.

Wind power is a growing energy sector in Sweden. However, it still represents only a small part of the total electricity production, about 0.7%. In order to create good conditions and to facilitate the establishment of wind power in Sweden, the government has for example, created a national centre for wind use. The objective has been to reach the governmental goal, which is an expansion of wind power by 10 TWh by year 2015 compared to the level in 2002. The Swedish electricity market was deregulated in 1996 which refers to the introduction of a competitive market in electricity production and trade.

The gas turbines in the Swedish secondary reserve are reaching the end of their technical lifetime, hence alternative solutions need to be considered. One of the solutions thought to have the greatest potential is the use of so called consumptionreduction. By entering contracts with large consumers, agreements are made to reduce consumption in the event of major disturbances in the power system and thus being used as a secondary reserve. This thesis investigates the feasibility of consumption reduction as part of the secondary reserve. This has been achieved by developing a requirement specification for the disturbance reserve and by studying the technical and economic potential for consumption reduction among a range of consumers.The technical potential for consumption reduction that fulfils the requirements for participating in the secondary reserve are on average 750 MW in SE 3 and 98 MW in SE 4.

Public participation in urban planning is meant to increase democracy in the planning process. Even though all citizens have the option to participate in urban planning debates, few seize their chance to partake. This thesis describes a study on how user needs are met and prioritized in design processes concerning urban planning. The aim was to determine whether user-centered design (UCD) methods could be used as an avenue for public participation in urban planning and ultimately invite more citizens into the planning process.The thesis details a design process where a team worked to develop Farsta, a suburb of Stockholm. The design problem was the question of how Farsta could become an attractive business location.

The gas turbines in the Swedish secondary reserve are reaching the end of their technical lifetime, hence alternative solutions need to be considered. One of the solutions thought to have the greatest potential is the use of so called consumptionreduction. By entering contracts with large consumers, agreements are made to reduce consumption in the event of major disturbances in the power system and thus being used as a secondary reserve. This thesis investigates the feasibility of consumption reduction as part of the secondary reserve. This has been achieved by developing a requirement specification for the disturbance reserve and by studying the technical and economic potential for consumption reduction among a range of consumers.The technical potential for consumption reduction that fulfils the requirements for participating in the secondary reserve are on average 750 MW in SE 3 and 98 MW in SE 4.

This Master Thesis is a product development project that has been carried out incooperation with Metso Paper Sundsvall AB. The task has been to develop a holdingsolution that generates force between two rolls and to evaluate the new solution withrespect to functionality, manufacturing, structural stability, costs, assembly etc. Theroll holding solution is a system that is part of a rollpress. The rollpress is used towash and dewater pulp. The existing solution creates forces that have to be absorbedby the gable of the press.

The gas turbines in the Swedish secondary reserve are reaching the end of their technical lifetime, hence alternative solutions need to be considered. One of the solutions thought to have the greatest potential is the use of so called consumptionreduction. By entering contracts with large consumers, agreements are made to reduce consumption in the event of major disturbances in the power system and thus being used as a secondary reserve. This thesis investigates the feasibility of consumption reduction as part of the secondary reserve. This has been achieved by developing a requirement specification for the disturbance reserve and by studying the technical and economic potential for consumption reduction among a range of consumers.The technical potential for consumption reduction that fulfils the requirements for participating in the secondary reserve are on average 750 MW in SE 3 and 98 MW in SE 4.

Constantly growing demands from the costumers in the Automotive industry forces the subcontractors to seek alternative ways to compete. One parameter of quality is the components tolerance against NVH(Noise, Vibraion & Harshness) aspects. Kongsbergs Automotive has developed a new gear shifter platform (Shift-by-Wire) that is sold to Alfa Romeo and used in of their car models. However, the company is not pleased with the components sound quality, therefore the main purpose of this thesis is to develope a number of concepts that is supposed to enhance these NVH-aspects.To get an understanding of the problem an analysis of the causes of the emitted sound has been done parallell to a product decomposition, function decomposition and a Ishikawa-diagram. Together with these methods has a litterature study been performed to get familiar with the physics of an impact and especially the emittment of noise.

This thesis is a Feasibility study into how Fresenius Kabi may rationalize their destruction process in regards to cost, recycling, and work environment. The two main objectives are to identify scrap flows and the possibility to improve or replace the equipment that is now carrying out the physical scrapping. The flow has been visualized by a flow chart of the material and communication. A chart of the problem established to visualize where improvements are necessary. Based on the problems proposals are presented on how to improve the flow thru the plant.During analyze of the physical scrapping equipment it was also necessary to take a deeper look at how they are carrying out there work today, how does the procedure look like, working environment and where are the weaknesses.

The community Vessigebro, in Falkenberg and its surrounding areas housing one percent of all dairy cattle and two percent of all pigs in Sweden. This means that there is a large amount of manure as a basis for producing biogas in the area. A number of farmers have therefore formed a cooperative named Vessigebro biogas and started the project Green Vessigebro, with the goal of creating the conditions for a more profitable and more sustainable agriculture production.The study deals with the conditions and sale opportunities of the Feasibility study Green Vessigebro. The study has looked at the work that was previously carried out for the biogas that could be produced on the farms in Vessigebro, The main pipeline for natural gas on the Swedish west coast and its operators, the Swedish Competition Act , Electricity Act , Natural Gas Act, the District Heating Act , Sustainability Act , previously proposed measures, municipality interest in biogas from Vessigebro , possible collaborations, possible sale opportunities and perform calculations with data from the municipality Ljungby for a suggested transportation of biogas between Vessigebro and Ljungby.The study shows that there are several interesting sale opportunities for biogas from Vessigebro. The production and use of biogas in Sweden is increasing and the trend seems set to continue.

Our everyday life is becoming more active and the activities we perform influence the way we dress. Due to an increase in activities undertaken in an urban environment, demands are changing and the need for active wear that meets the new demands follow suit. The four characters represented in the research can be seen as a reflection of the functional features needed, including base layer, mid layer/insulation and shell.Despite the increase in activities, most of our clothes are still constructed on static dummies or drafted on a table in 2D and the main developments within the active sportswear field is driven by material innovation. By creating garments on a body in movement, my aim is to develop new functions and expression in active sportswear through construction.Construction methods in active sportswear are examined and understood through observations and reconstructions and constitute the foundation of a study of movement for a design recovery.The movement and features required for leading an active urban life sets the direction of the development of new func- tional garments. A series of trial and error sessions and draping fabric on a live model in movement created the prototypes used in functionality tests to establish their feasibility.

The Swedish agricultural sector is currently experiencing substantial structural changes, where the number of agricultural enterprises continuously decreases and the average farm size increases. In order to maintain competitiveness, it is important to be aware and adapt to changes concerning the surroundings of the company (Johnson et al., 2011). Agricultural commodity prices sharply fluctuate on the global market in recent years, affecting the profitability of farmers. High volatility market requires tools to reduce price variations and increases the need of decision-making (Bouder & Beth, 2003). Farm-based grain handling facilities increases the sale options regarding agricultural commodities; a flexible strategy to get additional compensation for the storing the grain produced on the farm (Edling, 2002; Edwards, 2013).

This report was written as a result of a Bachelor Degree Project at the School of Technology and Society at University of Skövde spring 2007, together with Jede AB in Mariestad. The report covers the development of a door to a coffee vending machine that is under construction, and will in a chronological order describe the project from ideas to final product.The project started with a rather extensive Feasibility study that thru market research and user tests sorted out the opinions of potential customers, concerning today?s available assortment. Technical areas concerning materials and manufacturing methods were also scrutinized for the consideration of the possibilities of a future production.The next step was to constructively generate ideas and thoughts that later on could grow to be potential solutions. After several weeks of hard work and pieces of good advice and recommendations from the assigner, four comprehensive concepts were built up.

A design methodology to mitigate timing problems due to long wire delays is proposed. The timing problems are taking care of at architecture level instead of layout level in this design method so that no change is needed when the whole design goes to backend design. Hence design iterations are avoided by using this design methodology. The proposed design method is based on STARI architecture, and a novel initialization mechanism is proposed in this paper. Low frequency global clock is used to synchronize the communication and PLLs are used to provide high frequency working clocks.