This is a degree project performed at Halmstad University in Sweden on the subject carpet ofreinforcement. This project is developed in association with Celsa Steel Service in Halmstad.The purpose of this report is to investigate how much time that can be saved if carpet ofreinforcement is used instead of the traditional way to work with reinforcement and seewhat kind of parameters that is important between the choices. We are also going to seehow this product affects the situation for reinforcement workers from an ergonomic point ofview.Carpet of reinforcement is made by straight reinforcement?s bars that are welded togetherwith steel bands. These rolls are made at a Factory with a machine that welds together thebars in determined centre distance, with desired dimensions after the constructionengineers? blueprints.

Nowdays an efficient production is critical to achieve for companies competing on the market for steel cutting tools. One of such companies is Halmstad based Tooling Support Halmstad AB that manufactures threading-taps, threading-dies and parting off tools, towards a centralized warehouse in Schiedam, Holland. The large amount of different products, approximately 2500 is a big contributor to the problem along with a new order system that creates a demand of low setup times. Previously the company was forwarded orders through quarter based prognoses which enabled planning of the production over a longer time span. Currently the newer order system ZENIT is in use and the company thereby gets their orders weekly.

A study was carried in conjunction with the Orthodontic department at Halmstad General Hospital in Sweden to investigate the possibility of reducing cost and manufacture time of dental implant drill guides. The current system involves sending a digital image in STL format to the Materialise Factory in Belgium where information of the position of dental implants is translated onto a moulded mouthpiece. Drill guides are placed in the mouth piece which is then returned to the surgeon. The mouthpiece complete with drill guides is then placed in the patients mouth and used as a guide for the implant drill holes. The cost of 10000 sek and a turnaround time of 2 weeks gave rise to the need for a faster and cheaper solution.

AbstractThe future of ethanol is depending on good solutions for the production. ENA energy power plant produces electrical power and district heating by heating biofuel. By building an integrated bioenergy plant surplus steam could be used to produce ethanol as fuel to vehicle.This would mean that ethanol is produced renewable energy and the energy for the process derives from the surplus of power.  ENA energy, MDH (the University of Mälardalen) and the energy authority has initiated a research project were different bioenergy combinations integrate with existing power plant.  As a part of the project which size an integrated Factory should be to gain the best efficiency for the plant was investigated. Consideration will be taken to the cost of the production in order to be competitive to the price of imported ethanol.  Etanolens framtid vilar på bra lösningar för framställning.  I ENA energi kraftverk i Enköping produceras el och fjärrvärme genom eldning av biobränsle.  Genom att bygga ett integrerat bioenergikraftverk där skulle man kunna använda överskottsånga till att framställa etanol som fordonsbränsle.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Isaberg Rapid AB is a company that manufactures for instance staplers and glue guns. Headquarters and main Factory is located in Hestra but there are also subsidiary companies in Denmark, Netherlands, France, Spain, China and England. There are also two filial factories in France and China.Today has the company no logistic guidelines committed and that leads to problems since the salesmen promise different things to the customers. This contributes too many different logistic solutions for Isaberg Rapid AB. The company has also noted problems with returns of goods.The purpose with this task is to standardize and compile logistic guidelines, usable to all Isaberg Rapid AB's small to midsize customers.

AbstractThis degree thesis was made in cooperation with Chematur Engineering in Karlskoga.Many of the environmental issues of today are a result of the motor traffic. Consumption of fossil fuels harms our environmental through formation of carbon dioxide and other greenhouse gases. To get under control with our environmental issues it?s important to find substitutes for oil that are both cheap and environmentally friendly. Ethanol has a long history as a motor fuel and is both enviromentally friendly has a high efficiency.According to the EU commissions directives for motor fuels, 5, 75 % of all the fuels in Sweden should be renewable in 2010.

The purpose of this work was to see if it was possible to rebuild an old dairy house into a house fore sheep production. The goals fore the work was to see witch kind of production model was suitable, how the actual drawing would look like and witch kind of interior was needed. The building was built in the beginning of 1900. It is located on the mountain Kinnekulle in Sweden. It was a big production fore its time and hade about 60 dairy cows. It was a lot of hard work because the floor was built by big stone blocks and it was very hard to rebuild when some more automatic solutions came fore handling all the manure. The idea of remaking the building came when we rebuilt the roof fore 5 years ago.

Material handling is a term that includes all kinds of handling of material from a raw product to a finished one. ABB is active in the following segments; foundry, packaging and palletizing, metal industry and plastics industry.The demands for efficiency and reliability have been set very high in the industrial sector. Optimizing of the material handling will give the company higher cost-effectiveness. Around the robot there are different kinds of material flows, to optimize the cycle time, consisting of carriages combined in different ways.Motion Control is a complex system with main functions such as; positioning, synchronizing, indexing and more. The products in the system need to cooperate to make these functions possible therefore integration of motor- and servo products are important.

The aim of this project has been to raise the production efficiency of Daliff Precision Engineering through reduced transportation time and a more standardized manufacturing process. The problem has upraised because of a big and diversified product flora without any standard products and with just small batches ordered. The report also tries to show the work procedure with general analytical methods and be an example of how a similar problem can be resolved. The transportation time is being proposed to be reduced through a change in the layout of the Factory. By moving a few manual machines, dispatch and burring to more efficient locations, the total transportation time will be reduced by 55 %.

Considering that the current technology is constantly improving, it becomes increasingly important to have an efficient logistics in a company to maintain profitability while achieving a competitive business. Efficient logistics may be accomplished by improving the internal materials handling. In this thesis the internal material handling of steel frames has been studied at a Factory in Vaggeryd. The goal of this study is to investigate the problems that exist with the current production flow of products and provide suggestions on how it can be developed to reduce unnecessary handling and movement.The study has a deductive approach where the authors has been using literature studies parallel with empirical analyzes conducted at a company to achieve the purpose of the study. Documentation from the company and interviews with staff and observations form the basis for the data collection carried out.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The company System Andersson is developing systems for controlling materials and production in industries. They want to add a new service, where parts of those systems are accessible through cell phones.In this paper we are investigating which technology are best suited for this kind of application. And then we describe how we are developing a prototype fort this application, based upon that technology. After investigating technologies such as Java ME, Microsoft Silverlight, and web applications we settled upon building the system as a web application, customized for a mobile environment.To build a web page which is readable by many different cell phones we use the markup-languages which are developed for cell phones. We put much effort in reading about the standards and recommendations for the mobile web, produced by the organizations W3C and OMA.

This Master?s Thesis aims to investigate and assess the methods used to decrease the discharge ofmetals, primarily copper, from the water purification plant at Assa Industries plating Factory inEskilstuna.Literature studies of the purification methods precipitation, ion exchange, evaporation, reverseosmosis and electrolysis has been done to appraise the adequacy of the technique. Thesetechniques are commonly used for purification of industrial waste water.Assa has four plating lines: the Trumline, the big Zinkline, the new Zinkline and the Decorativeline. The new Zinkline is the most modern of the four lines and purification is done byrecirculation over an ion exchange unit. The demand for fresh water is thereby heavily reduced.The Trumline, the big Zinkline and the Decorative line all use older techniques.

BillerudKorsnäs is a leading global provider of primary fiber-based packaging materials and on Gruvöns Bruk in Grums, they have chosen to invest millions in the boiler at the facility to increase the total capacity of the Factory. This results in the Pulp Flash Dryer at Gruvön being burden more, which makes it important that it is of great reliability and can be run with a high capacity. The reliability of the Pulp Flash Dryer at Gruvön is not as good as one could hope, which leads to reduced availability and production, as well as to increased maintenance costs. There are a number of different reasons for this, but all the casual links are not known.The purpose of this project was to perform a system analysis of the Pulp Flash Dryer to identify bottlenecks and the most critical parts from a capacity- and availability perspective. Appropriate methodology for the system analysis was used and would be used in a structured way to perform the analysis with data from the process and the maintenance system.