Understensho?jden is Stockholm's largest eco-village which was built in the early 1990s with the vision of enabling ecological living for people. However the ecovillage is no longer considered as environmentally friendly because of its relatively high energy consumption, and non-updated energy system. The purpose of this study is therefore to investigate how Understensho?jden should reduce their energy consumption and upgrade its energy system by using Blower-Door, IR-camera and Design Builder.

Waste appears to be a low-cost fuel compared to biofuel. This Masters thesis was conducted for Vattenfall Utveckling AB and deals with how waste in the fuel affects the performance of a SCR-catalyst. Different mechanisms of deactivation were surveyed, focusing on the poisoning mechanism. A literature study was carried out, which was used as a reference when analysing the results.Small samples (9x2x2 cm, 64 pieces) cut out from a full-scale unused honeycomb catalyst were exposed up to 1500h in two different combustion plants, Johannes in Gävle (co-combustion) and Högdalen in Stockholm (waste-combustion). The activity was measured mainly at 300°C but also at 250, 350, 375 and 400°C.

This report was written by Sofia Ericson and describes the degree thesis with the title: ?Connections between the growing site of bio fuel, the chemical composition of bio fuel ash and the deposit growth in a bio fuel fired boiler.? The purpose of this degree thesis was to avoid melted deposit growth in the bio fuel fired boiler at ENA Kraft in Enköping. Potassium and sodium are known to lower the melting point of bio fuel ashes and are therefore not wanted in the trees in higher amounts than necessary for the growth. Silicon is also known to be important for the deposit growth but it is not possible to say in general if higher or lower contents of silicon is better. The relation between silicon and other chemical substances is more important than the total amount of silicon.

The background for my thesis is the fact that with rising electricity and oil prices it becomes interesting to calculate on alternative heating systems. I have chosen to calculate upon my parents? farm, which today heats the dwelling house with wood. This is very time-consuming work, time which could be spent on other work. The main objective for this study is to compare three different heating systems to decide how they differ considering effort and cost. The result from the calculations was that grain-heating system demanded the least amount of work, but the total cost was a little higher compared to chips heating. Chips heating required half as much work as today?s wood heating and had a little lower total costs compared with the corn heating. Which system to choose largely depends on how the own work is valued.

Göteborg Energi has a surplus of district heating during spring, summer and fall. The heat surplus is due to a constant production of waste heat from oil refineries and heat from waste incineration over the year. It would be desirable to increase the demand for heat and the uptime for the newly built combined heat and power generation plant, Rya Kraftvärmeverk. One alternative could be to integrate Rya Kraftvärmeverk with a pellet production facility. By producing heat, electricity and pellet in a joint process the energy use can be decreased.

The Swedish government has introduced a goal to reduce the energy intensity by 20% to the year 2020. To reach this goal actions need to be taken throughout the energy sector which includes residential and commercial buildings. This thesis considers the possibility to reduce the energy usage in a building located close to Uppsala. The analyzed building is a combined office, cafeteria and entrance and was completed about half a year before this project started. Therefore the measures presented for a more energy efficient building are presented as measures for future constructions.Simulations have been made in VIP-Energy, a dynamic energy calculation program.

The idea to develop  a platform for a PID-controller came from the need to control the temperature in  an espresso machine in a more exact way than a thermostat could perform. In discussions with Syntronic AB the idea developed into PID-control for industrial use. Syntronic AB suggested that the platform should be based on a commercially available processor module to shorten the development time. The suggestion included the use of the microcomputer Raspberry Pi, which supports USB, HDMI, memory card and Ethernet.The work began with establishing a schedule for the 10 weeks of the projects duration, and after that a system specification listing all functions, implementation and limitations was made. When the foundation of the system specification was done, a preliminary system design took shape.Because of the Raspberry Pi´s lack of Analog-to-Digital converter, a circuit board containing Wheatstone bridges, differential amplifiers and a two channel Analog-to-Digital converter was fabricated.

Gunsta is situated about 10 km east of Uppsala. Today there are plans to establish 1000 new households in Gunsta before year 2030. The required energy for heating houses and water would be distributed via a district heating system, which also includes 200 existing residences. The annual required energy, according to this study, would be 16.2 GWh with a maximal peak effect of 6.9 MW. To meet this need, the study suggests a system with heat pumps to upgrade the 31?C water from a 1.8 kilometre deep borehole.

The main goal with this thesis report was to come up with ideas of how to make the use of energy more effective and thus save money for the company.First a survey was made to find out where and how the energy consumers were divided within the company. The results were then used in calculations to find out how much money that could be saved and how long it would take to get back the investments.There is a big potential in saving money by recovering heat from the UV-lamps with a heat exchanger. It would also even out the pressure in the factory which is a source to heat loss and a cause for discomfort amongst the employees. It?s possible to save 105 000 kr in a year and the money needed for the investments is 600 000 kr.By using the recovery air more effectively the company could save up to 250 000 kr a year in lowered heat purchases, but this would require the use of automatic dampers.If you reschedule the running times for the wood chipper and invest in some kind of load management, for example Sydkraft?s ?Energidirigent? you can save at least 42 000 kr.

Our purpose in this paper is to examine if there is any profitability for a company with a factory in the timber industry to invest in a combined heat and power, CHP. Based on analysis and the results that the paper generates, we will give Derome AB a suggestion on how it is a profitable investment or not to installing in a CHP.By investing in a CHP plant, you can get a high efficiency, which means that companies can use their resources more effectively. The Swedish wood industry has by-products of production that can be used for combustion in their boiler which is an advantage.The essay is a qualitative study where we have a case company, Derome AB. In this company, we interviewed two employees who have knowledge in the study. They have helped us to provide information and data about their business.We chose to use the pay-off- and the net present value method, NPV, to see if there are profitable advantages for the investment.

All products will eventually end up as waste, which in a sustainable society has to be handled in an efficient and environment friendly way. This report focuses on waste fractions meant for combustion, often difficult to characterize. However, more homogeneous fractions that are treated biologically are also discussed.The study concerns the region of Borås, Sweden, where the waste plant Sobacken has provided a good starting point. On this site, fuel to the Energy-from-Waste plant of Borås Energi is prepared and the biological waste is treated through anaerobic digestion.One important part of the study has been to collect experience-based knowledge from the technical staff at Sobacken and Borås Energi. This information was compiled into an overview of wanted and unwanted fractions to the preparation plant and the boilers respectively.

Emission of nitrogen oxides as well as carbon monoxides is an inevitable result of combustion. A Swedish law "Law of environmental fee for emissions of nitrogen oxides as a result of energy production" (lagen om miljöavgift på utsläpp av kväveoxider vid energiproduktion (SFS 1990:613)) controls the emission of NOx from energy production by a system of fees. The system has resulted in a strong approach toward less emissions of NOx among the energy production plants. High emission levels, today exceeding 52 mg/MJsupplied fuel, leads to costs for energy production companies. This paper examines possibilities to reduce the emissions of NOx by optimization of the SNCR-technique in a biofuel fired heat and power plant.

The purpose of this bachelor´s report is to expand the knowledge about heat supply of a small house in Malmö. The heat supply will be provided from solar panels in combination to two accumulator tanks which will storage the up heated water and a pellet boiler.The technique used here is warmth storage in water over seasons, which will provide the total need of heating for the house. Accumulator tanks in combination to solar panels gets more and more common in Sweden but this far it´s unusual to use it for storage over seasons. This report will highlight many of the difficulties associated whit heat storage and give information about a system's possible design and function.The design of this system is decided early on. An accumulator tank is placed 2 meters down in the earth on the backside of the house.

The moisture content in 10 deliveries of tree parts and 10 deliveries of wood residues were measured with different methods to analyze the quality of procedure used at Dåvamyran today. At the same time a survey was made on the measure procedures used at heating plants in Sweden The majority of the heating plants in Sweden use weight and moisture content as base for payment but at some plants only volume. The moisture content is usually estimated by drying wood chips in an oven but few plants a visual estimation is used. At few plants moisture content is estimated spectroscopicily. The techniques using near infra read light and other electromagnetic are still at a test stage. The methods of measurement used today are quit unreliable for the individual deliveries and there is a risk for systematic mistakes.

In June 2006 the Swedish government decided that the use of energy in buildings should be reduced by 20 percent until 2020, compared to the level of energy used in 1995. To contribute to this goal, the real estate company ?Eskilstuna Kommunfastigheter AB?, set up own goals for their buildings. In 2009, the goal for schools was to have a maximum energy use of 118 kWh/m2year for heating and hot water.The school ?Hållsta skola?, just south of Eskilstuna, exceeds the limit since it used 270 kWh in 2008.