This report describes how a syringe pumpwas developed for Q-linea AB inUppsala Science Park as a bachelor´sthesis at Uppsala University. Thepurpose of the syringe pump is toreplace existing pumps in one of Qlineasdosage instruments. The reasons for whythe pumps are replaced are that they arebig and heavy. Therefore the task was todesign a smaller and lighter syringepump.The goal of the project was to create aprototype of the design that met themechanical requirements posed. Therequirements were met.In the report the work process can befollowed from the development of thespecifications to the final design andtests of the prototype.

This master thesis was a continuation of a previous study in the diesel exhaust characterization, which is part of the academical work embedded in the EMIR-1 project. The main objective of this thesis work was to finish the installation and make the proper modifications of the particulate mass measuring system located in one of the engine test cells at KTH, in order to be able to measure the mass of the particles from the exhaust of diesel engines.This experiment requires a diluted flow sample from the exhaust that should be sent to the device that makes possible the measurement of particle mass, called TEOM. In the first stage of this project, the objective was to study and make the proper modifications in the existing KTH diluter because there were several problems to obtain a constant dilution ratio from it during tests.This modifications were made and it resulted in a great improvement in the maximum inlet and outlet flow that this diluter can handle. Therefore another modification is proposed for controlling the inlet exhaust flow so it will be possible to regulate the dilution ratio and make it constant along a wide range of engine loads and speeds.The second and most important stage was to make particulate mass measurements possible by analyzing the frequency signal from the TEOM device. The idea was to obtain the frequency of oscillation from the tapered element in the TEOM, and therefore with the proper correlations, be able to predict the particulate mass concentration in the exhaust flow from the engine.An electrical problem in the TEOM circuit was detected and corrected, so the signal that carries the frequency from the TEOM can be analyzed properly.

As a part of the fight against the global warming the energy production needs to be more efficient and redirected towards sustainable options. One alternative is cogeneration, which means that electricity and heat is produced in one plant. The purpose with this survey is to examine if there are any commercial available combined heat and power techniques, based on combustion of solid moist biomass, which are suitable to small-scale applications. The technique must be able to produce between 2 and 10 MW thermal and the heat demand is a Swedish district-heating system. When already published reports had been studied, the Organic Rankine Cycle (ORC) was chosen as the most suitable technique.

The thermal response of a borehole field is often described by non?dimensional response factors called gfunctions.The g?function was firstly generated as a numerical solution based on SBM (Superposition BoreholeModel). An analytical approach, the FLS (Finite Line Source), is also accepted for generating the g?function. In thiswork the potential to numerically produce g?functions is studied for circular borehole fields using the commercialsoftware COMSOL.

The aim of this study is to illuminate factors in nurses´ work, which can cause a state of exhaustion called burn out. The results indicate that work related mental illness is a lengthy process that gives rise to both physical and psychical problems. These problems might lead to a state of burn out. However, several authors prefer to use expressions like exhaust syndrome or exhaust depression as they are criticising the concept of burn out. The study is a literature analysis of 11 scientific articles that have been scrutinized using the criterions presented by Polit et al (2001).

Gtherm is an innovation company who has an unique air heat exchanger underdevelopment. The purpose of this thesis is to provide data of suitable motors for theheat exchanger and to find suitable motor suppliers.A motor specification was designed. It is an important basis for the search of suitablemotors. A compilation was made of nine motor suppliers and the suitable motorsfrom those. The compilation can be used by GTherm in their choice of suppliers andmotors.The compilation of the demands on the motor and analysis of suppliers indicated thatthere were no standard motors available to GTherms air heat exchanger.

The main environmental problem for aviation is the great amount of exhaust gases, mainly nitrogen oxides, carbon monoxide, carbon dioxide and hydrocarbons - mostly "greenhouse gases" leading to climate changes. I decided to sort out what is being done to decrease these problems and what regulations there are concerning air pollution by the means of searching the internet and using publications from aviation authorities for current figures. I chose to scrutinize authorities on political, authority and company level, resulting in summarizing the work of UN and EU respectively, ICAO (International Civil Aviation Organization), JAA (Joint Aviation Authorities) and LFV (Swedish Civil Aviation Authority), and finally SAS, representing the airline companies. Conclusion that I have drawn are thatthere are regulations for air pollution, written down in ICAO's Annex 16, that are to be followed. Secondly, LFV are environmentally controlling their nineteen airports and since economy is an important reason for not giving priority to environmental issues in aviation emission charge and noise charge are added to the landing fees.

The dishwasher is a wide spread product that occurs in many households. It saves the user time,water and energy. When using a dishwasher instead of doing dishes by hand a lot of energy issaved.The importance of lowering the energy consumption does not only come from the consumerwinnings but also from an environmental point of view. Scientists are certain that the globalwarming comes from the emission of green house gasses that is created by human consumptionof oil, gas and coal.Dishwashers today are a lot more energy efficient than older dishwashers, but there are stillmargins to lower the energy consumption. The aim with this project is to investigate thedishwasher and it?s washing cycle, noting different phases and components that contribute towaste of energy.

The aim of this thesis is to develop a new business model for district heating and cooling firms which can contribute to a stabilization of the Swedish national energy system. The business model is developed for a district heating and cooling firm and is exemplified with Fortum Heat. The theoretical investigation around the topic creates a rigid base for following qualitative empirical studies. Osterwalder?s canvas for business model generation is used together with a Casual Loop Diagram to identify a number of business opportunities which stabilizes the national energy system.

The report is a master thesis about energy efficient measures for an underground facility Hemsö fortress.Several proposals are evaluated economically.Statistics of the electricity used and measurements of several heat pumps are analyzed to find energysavings potentials.The results indicate that several units of a dehumidification system are responsible for over 70 % of theyearly electricity cost. The air that is being dehumidified by these units can otherwise cause damage ofculturally important interior designs.The proposal with highest profit suggests an alternative method for dehumidification. The cooler in theair handling units in Hemsö fortress have capacity to dehumidify the air. However complementary fansneed to be installed to circulate humid air towards the air handling units. The solution can be implementedin three different locations within the facility.

The study aims to reduce energy consumption in apartment buildings where individual metering and charging of heat is applied. The aim is to develop planning and design for individual metering and charging in apartment buildings.The study is based on literature review, interviews and case study that include analysis of existing documents. Interviews were carried out with the property developer and the involved consultants who planned the apartment building Yasuragi. To investigate the differences the condominium association has noted in heat consumption between flats, the debit values of the heat were used to discern which houses that were furthest from the average consumption. On these flats there were temperature measurements and thermal photo shoots made for discriminating behavior and possible construction techniques which could be the explanation for the heat spread.Boverket shows that the consumption of heat can be reduced by 10-20% after insertion of individual metering and charging in an apartment block.

This degree project handles acoustic measurements of the heat pump EcoAir 107, made by Enertech CTC AB. The sound from the three sound sources of the heat pump, fan, compressor and four way valve, have been measured to find out how they affect the total sound level of the product.Measures to attenuate the sound level have been developed and tested. By comparing these with the sound of the heat pump, in its original state, we have found out the measures which have best effects.The best attenuating measures came to be: taped openings and holes around the compressor space, isolating the top and the bottom of the whole construction, support of the fan bottom part and shielding of the sound source with a screen at a distance of 110 mmThese measures have been tested together and an average attenuation of the total sound level with 3,9 dB have been accomplished. In the front of the fan where the continuous sound is the strongest, the attenuation was 4,7 dB.This project is meant to be used as a guide by Enertech CTC AB:s during their future developing process..

This thesis is done in cooperation with SWECO Energuide in Växjö. They have been assigned by SKB in Oskarshamn to renew their electrical power supply and the ancillary processing systems in their Central provisional storage of spent nuclear fuel, CLAB. Today in the CLAB facility, the spent fuel is cooled down with water pumps, driven by asynchronous induction motors, where the water is regulated by mechanical valves to the desired flow. After the upgrade, the engines will be powered by AC drives that can control the pumps by changing the rotational speed and thus change the water's cooling effect on the nuclear fuel. In this study, I investigated the interference AC drives causes the feeding network and how to go about averting them.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

To achieve the requirements to decrease emissions of greenhouse gases by 20 % by 2020, Swedenneeds to increase its use of bioenergy. In doing so it seems natural that those who already haveaccess to large amounts of biofuels in the form of by-products such as straw, wood chips anddigestible materials take advantage of these assets locally. By combining production of heat withpower production at the farm it may be possible to not only reduce the direct use of fossil fuel forheating but also reduce energy costs.The purpose was to simulate different cases of using a small scale biofueled combined heat andpower plant for farm-based systems. A MatLab-model was developed and used to draw conclusionsabout the costs for production of heat and electricity with different conversion technologies.The model uses climate data to simulate the variations in heat energy demand on a day-to-day basis.The given heat demand is the base of the simulation and from this the possible electric output iscalculated. This study has focused on the impact of the following properties: electric-, heat- andtotal efficiency, fuel, fuel price and specific fuel requirements.