ANVÄNDNING AV PCA-PUMP UR ETT SJUKSKÖTERSKE-PERSPEKTIV EN ENKÄTSTUDIE BODIL ANDERSSON-FRANKE ANNA FRIDÉN-HANSSON Andersson-Franke, B & Fridén-Hansson, A. Användning av PCA-pump ur ett sjuksköterskeperspektiv. En enkätstudie. Examensarbete i omvårdnad 15 högsko-lepoäng. Malmö Högskola: Hälsa och Samhälle, Utbildningsområde omvårdnad, 2009. Syftet med denna studie, var att belysa sjuksköterskans erfarenheter och upplevel-ser av PCA-pumpsbehandling som en del i smärtlindringen inom postoperativ omvårdnad.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Chapter 1 defines the aim of the project and gives a general orientation about ground heat extractors. In chapter 2 physical processes that could be expected to be involved in the heat transport around a ground heat exchanger are discussed. It is shown from a literature study what amount of moisture transport due to thermal gradients there could be expected in a ground heat exchanger. The conclusion is drawn that the moisture gradient (Sr) is of same magnitude as the driving temperature gradient (°C). At the expected amount of increased moisture around the pipes the moisture transport could be considered to have a little effect on the brine temperature.

Norconsult AB has developed a solarhousing concept, a house designed for the warm climate in the Middle East andwith large quantities of solar panels installed. The cooling system for the house was designed in an earlier report, the purpose of this thesis is to investigate the possibility of short and long term storage of thermal energy via an underground energy storage volume.Two different designs of the storage and three different filling materials have been integrated into a model to simulate different cases. The first design consisted of pipes installed in the ground, without insulation. The second design consisted of an insulated concrete box installed to prevent thermal energy from the surrounding soil to flow towards the lower temperature regions within the storage. The three different filling materials were dry saudi sand, water saturated saudi sand and the filling material used by the client for energy storage in Sweden.The results from the simulations show that neither of the designs, regardless of the filling material, managed to extract enough thermal energy from the house to the ground to uphold the demands of indoor climate.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

The work covered in this report includes a literature study of the diesel dual fuel technology(hereinafter referred to as DDF). The literature study covers earlier work that has been doneregarding the use of compressed natural gas (CNG) and diesel in a DDF system. Moreover a onecylinder research diesel engine was fitted with a CNG fuel system for experimental testing. Theinstallation of the engine and the test cell is described. Results from the tests are presentedcovering emissions, heat release and pressure traces from the DDF-concept.During the literature study it was found that most research was related to heavy duty dieselengines.

The rising demand for electricity and heat raises a big challange for the society and engineers. Many products have been introduced to the market to supply more energy to the energy systems. Absolicon AB is a Swedish company that develops and markets a combined heat and power generating product. The product, Absolicon X10, uses a parabolic trough to concentrate the radiation of the sun onto a receiver. The receiveris equipped with mono crystalline solar cells and is cooled by a circulating liquid media.

Biogas is a gaseous fuel, rich in methane, produced through a biological route in an anaerobic digester. A gas engine generates combined heat and power, which can be used at the farm to reduce energy cost. The process also generates a digestate, with better utilization of nutrient compared to cattle manure. The aim of this study is to analyze the profitability of a farm-scale biogas plant for combined heat and power (CHP) at Wapnö. Wapnö is an agriculture company located in the southern part of Sweden.

The energy in laundry rooms, in form heated air, can be utilized with a heat exchanger. A concept and an early prototype of the heat exchanger have already been developed to show that the theory works. This report describes the continued development and construction of the product.A field study was made in order to investigate the environmental usage and establish the product design. The most common washing machine was used as a calculation model, and calculations were also made to estimate the amount of energy in the air. A previous analysis of the existing prototype is also presented in this report, to show the products potential capacity.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

In this work an assessment of the compressed air system in the facilities of Vattenfall Heat Uppsala has been conducted. The facilities constitutes, among others, a combined heat and power plant, and two waste incineration plants. The compressed air is supplied primarily by seven rotary screw compressors and yearly electric energy consumption in these has been determined. Furthermore, the usage of compressed air has been mapped in order to find processes with energy savings potential. Several suggestions how to reduce the usage of compressed air have been presented, resulting in decreased need of electric energy and reduced CO2-emissions.The results show that total need of electric energy in the compressors, during a standard production year, amounts to 5.83 GWh.

Uppsalahem AB is a municipally owned real estate concern that owns and administrates housing for nearly 30 000 people. The company puts a lot of effort into reducing the energy use of their housing stock. This project is a master?s thesis in the energy systems programme at Uppsala University, carried out in collaboration with Uppsalahem. The aim of this thesis is to provide energy saving measures for fourteen student housing buildings in Uppsala, Sweden.

Sala Silvergruva AB är ett av många företag som just nu kämpar med höga energi-kostnader. Denna rapport undersöker vilka möjligheter det finns att skapa ett hållbart energisystem i Sala Silvergruva med avseende på ekonomi, miljö samt sociala aspekter. Rapporten undersöker nio tekniker; vindkraft, vattenkraft, solfångare, solceller, pelletspannor, värmepumpar, effektivisering samt lagring av värme från växthus respektive fjärrvärme. Dessa analyseras var för sig med utgångspunkt i tio krav som speglar hållbarhetsaspekterna. I samband med analysen ges rekommendationer angående investering i respektive energilösning. Rapporten mynnar ut i en resultatskarta där det tydligt framgår vilka krav de olika teknikerna uppfyller. Den följande diskussionen leder fram till en slutsats som presenterar vilka åtgärder som bör vidtas i syfte att skapa ett uthålligt energisystem för Sala Silvergruva AB. Pelletspannor och värmepumpar visar sig i nuläget vara de mest uthålliga tekniklösningarna.

The milk production per cow has increased considerably during the last 50 years and due to the breeding for higher milk production also brings decreased reproduction efficiency. In a Swedish study 1996 it was shown that on average only half of all estruses were detected. Every time a farmer fails to detect oestrus it costs the farmer about 1200 Swedish crones and the need of means of detecting oestrus is therofore large. With this study we wanted to investigate if heart rate respectively crystallisation of vaginal mucus (arborisation) could be useful means of detecting oestrus. We monitored two oestrus cycles in four heifers.

The company Sol & Energiteknik wanted to examine the possibility to make a standardhouse totally energy independent. Based upon this I have, during the spring of 2007,examined the possibilities available at the market today through litterature studies, contactwith several companies and reading reports at the internet.The first thing to examine has been to determine the energy consumption for a standardhouse, and find out if there are better technologies to be used for energy conservation.My conclusion in this matter is that there are possibilities today for building a house moreenergy efficient.When I had reached the point at which my design for the house was decided, I also hadto choose the different products to use to produce energy as well as to store that energy.To produce heat and electricity to the house I decided to use a wind turbine and a solarwater heater.The most difficult part of designing a house that is energy independent is that theproduced energy must be stored somehow. Storing the heat is relatively easy beacuse theheat can be stored in a large water tank. The electricity is a bigger problem beacuse itmust be stored in batteries, which today are too expensive to be used in a standard house.In the future producing and storing hydrogen might be used to produce electricity, buttoday that technology is both expensive and not tested enough.My final conclusion is that a standard house can not be built to be totally energyindependent today, unless it is very expensive to connect the house to the electricitynetwork. As an alternative solution I came up with a proposal for a house which isconnected to the electricity network and have some amount of own produced energy.This house prooved to be a good investment if you choose to build it today, and it couldbe a very good investment in the long run beacuse energy prices increase every year..