This thesis includes an energy survey of the Herrgården pre-school, which has a modern heating- and ventilation system, and a comparison with Östers pre-school which has an older system. An energy survey of Östers pre-school has already been done by a group of three students and all the calculations and values have been collected from that survey. As of today, both pre-schools are heated thru district heating. It will be much easier to make smart and feasible energy-saving-measures by first conducting the energy survey.Herrgården pre-school in Gävle houses 81 children, therteen teachers, one cleaner and one cook. It was finished in the middle of 2009 and the staff has been very pleased with the in-door climate.

Syftet med arbetet är konstruera en balanseringsutrustning för pump- och fläkthjul åt Billerud Karlsborg. Det finns en balanseringsutrustning på företaget idag, men den klarar inte av alla dimensioner på pump/fläkthjulen varför en bättre lösning vore önskvärd. Målet med det här projektet är att kunna presentera en lösning på en balanserings utrustning i form av ritningar på själva stålkonstruktionen samt ett förslag på hur drivning av utrustningen skall ske. Därmed skall projektet tillhandahålla Billerud med tillräcklig information för att en ny balanseringsutrustning skall kunna tillverkas. Utrustningen bör klara av att balansera rotorer med en vikt på upp till 250kg och en största diameter på 1500mm.

Local charges may induce people to change their pattern of consumption by influencing investments and acts in certain directions. Some charges could for example give people incentives to use less natural resources. This study investigates four different local charges and whether they benefit an economical management with natural resources or not. This is carried out by investigating whether there is a polarity between local charges that may influence environmental actions or goods, and effective pollution control set to achieve certain nationally determined environmental goals. The study includes two economic perspectives and investigates on the one hand whether local charges counteract governmental subsidies and on the other hand whether the charges vary between the different municipalities since large differences may lead to cost inefficiency.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

The objective of the essay was to identify the nursing care required by a dog suffering from heat stroke and how to educate and advice the owners how to start treating their dog and prevent the condition from occurring in the first place. The essay is based on a literature study. Several databases were searched for scientific research to try find answers to the issues. Keywords concerning the subject were used and mixed in different combinations to sort out the suitable studies. The results of the study indicate that the dog should be cooled by the owner directly after detection. The most crucial issue is to reduce the body temperature as quickly as possible or the morbidity will worsen.

This report describes the work of developing a specification of requirements for Waste Heat Recovery Units. The main part of the paper describes how the work with the specification of requirements has been performed. One specific question to be answered is:What are the customer?s demands in case of properties for the Waste Heat Recovery Units and how is that information collected as an order documentation to suit the business area Oil & Gas?The report begins with a description of the assignment and continues with the aim and background. A theoretical part describes the different areas and methods that have been important during the process.

To provide our company a new business opportunity I have in this essay examined the economical possibilities to sell energy. I have chosen to do a case study on my own farm in this essay. The farm is focused to cropping and also have some properties for hire. The farm is situated in the village of Fjelie and that?s where the opportunity for selling heat are. Fjelie has about forty houses. The idea is to build a plant where straw is being used as fuel.

The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.

The objective of this study is to examine the sustainability of recovering industrial wasteheat from several heat sources in a foundry constructed in a plant belonging to ITT Waterand Wastewater in Emmaboda, Sweden. A triple bottom line perspective will be appliedto achieve this objective. The triple bottom line approach takes into account ecologicaland social performance in addition to financial performance. The technology forrecovering the waste heat is a Borehole Thermal Energy Storage (BTES) which is aconstruction consisting of 140 vertical boreholes, 150 meters deep with an internal spaceof four meters.The calculated amount of energy for storage is approximately 3800 MWh annually. Ofthis amount 2500 MWh are expected to be utilized, while storage losses accounts for theremaining part.

In this work we have compiled results from various studies concerning medical conditions that may possibly be avoided by castration and the effects that may occur after castration of the healthy bitch. The work is a literature review but it also includes a summary on the age recommendations for castration of the healthy bitch, castration before or after the first heat and the castration method most commonly used of ovariohysterectomy and ovariectomy. The summary is based on a questionnaire answered by personnel from 20 veterinary clinics and animal hospitals evenly distributed throughout Sweden.The summary showed that ovariohysterectomy was the most common method of castration and the recommendation in age ranged from 6-12 months. Regarding castration before or after the first heat 75% of the veterinary clinics and animal hospitals answered that they recommended castration after the first heat. Literature study shows that there are both advantages and disadvantages of castration of the healthy bitch and that it therefore is important that each bitch get a personal and individual evaluation before a decision is taken concerning a castration..

Atlas Copco Tools develops and manufactures handheld industrial tools. Heat and surface treatments are used to provide the tools with certain properties. There are no routines for the choice of treatment or for how to specify treatment on drawings. Production documents that are sent for production abroad may not be clear enough. Some treatments are known as trademarks and there are no instructions for how to specify these on drawings and in CAD-models.The purpose of this master thesis work is to create recommendations for the procedure of choosing heat and surface treatment.

The aim of this study was to develop a load prognosis model for Uppsala district heating system to be used as a tool for heat production optimization. The methodwas to build three models for the different customer types; housing, industry andoffices and then scale them for the total system using data from Uppsala districtheating system. The heat load consists of two parts, one that is temperaturedependent and one that is dependent of the social behavior of the customers. Thetemperature part was modelled with an ARX model using an outdoor temperatureprognosis as input signal. The social behavior part was modelled using the mean ofthe social behavior from some days before and additionally by distinguishing betweenweekdays and weekends.

MålsättningAtt utreda skillnader i tillgänglighet till insulinpump mellan olika patientgrupper samt vad som orsakar ett byte till insulinpump.MetodData från 7224 individer med typ 1 diabetes vid tio olika vårdenheter analyserades för att utreda effekterna av njurfunktion, kön, långtidsblodsocker, insulindos, diabetesduration samt ålder. Jämförelsen mellan patientgrupper utfördes med logistisk regression som en tvärsnittsstudie och Cox-regression för att utreda vad som föregått ett byte till pump.ResultatGenom logistisk regression erhölls en bild av hur skillnader mellan patienter som använder insulinpump och patienter som inte gör det ser ut i dagsläget. Cox-regressionen tar med ett tidsperspektiv och ger på så sätt svar på vad som föregått ett byte till insulinpump. Dessa analyser gav liknande resultat gällande variabler konstanta över tiden. Kvinnor använder pump i större utsträckning än män och andelen pumpanvändare skiljer sig åt vid olika vårdenheter.

This thesis examines different methods for the cooling of data centers. Several means of cooling with the refrigeration cycle have been studied, as well as the feasibility of using free cooling in different parts of Sweden. In addition, the possibilities of transferring excess heat to a nearby district heating system were investigated. It was found that in all investigated cases except two, the data center could be cooled solely with free cooling for at least 300 days a year when only the outside air temperature was considered as a constraining factor. The limit was then set to 20 °C.The vast majority of all district heating systems in Sweden get little to none of their heat from other excess heat sources.

SammanfattningEn ånganna monterades i EGR (Exhaust Gas Recirculation) slingan på en 12,7 liters Scania Euro V motor (DC1306). En modell som beskriver Rankine cykel togs fram med vatten som köldmedium i simuleringsverktyget GT-Power. Ångpannan i GT-power modellen kalibrerades m.h.a experimentell data.Simuleringarna visade att det optimala ångtrycket, det trycket där högst effekt kan erhållas från expandern, är beroende av EGR temperaturen. Det innebär att ju högre EGR inloppstemperatur desto högre optimalt ångtryck. EGR temperaturen i punkt 2 i ESC cykeln är 514? C för denna motor, vilket resulterar i ett optimalt tryck på 120 bar enligt simuleringen.