The aim of this report has been to investigate the use of electricity energy before and after a conversion of foodservice. The ambition was also to highlight the food safety and the retention of nutrients in relation to the conversion. The methods being used were qualitative interviews, case studies, study visits and literature. The equipment and the use of energy was the same in 2008 as in 2011 for hot-holding of the tested component, sauce with ham. The chilled system used more than three times the energy and cost for one portion than one portion in the hot-hold system.

Vid Volvo construction equipment AB, Component division i Eskilstuna, har nedväxling i förpackningsstorlekar genomförts som en del i en omfattande omställning mot Volvo Production System och Lean. Genom att producera med mindre satsstorlekar och hemtagningskvantiteter, vill Component division sänka sin kapitalbindning och bli flexiblare mot variationer i produktionen. Dessvärre påverkar nedväxlingen förpackningskostnaden till följd av ytterligare hantering, transport och administration. För Component division är det viktigt att få en god uppfattning om hur alla förpackningskostnader utvecklas med tiden. De vill i framtiden följa ett lämpligt nyckeltal för att se hur effektiva de är inom förpackningslogistik samt hur beslut och förändringar påverkar kostnaden.

The aim of thesis was to, through a action research study and through individual interviews with five students, clarify their perspective on educational assistance in high school. The study shows that students prefer teaching in small groups outside of regular whole class because it gives the them access to the factors they consider crucial for a functioning support-time whit a skilled and dedicated teatcher, in a calm and safe environment. Moreover, the students claim the importance of technical equipment especially in the Swedish subject, but also in other subjects. Today the educational assistance varies from an outside-the-class teaching situation to a whole-class situation with teacher support as well as technicaal equipment. When the student were asked to describe the cinditions under which studies can be conducted with the whole class they tried to imitate the learning environment they have in a small group.

In this essay, we have compared a conventional house to a passive house. The housesshared the same local conditions; they have the same living area and the same layout. Thedifferences between the houses were the different construction solutions for the roof, theouter walls, the floor and the heating system. Both the houses qualify the standards fromBBR and the passive house also lives up to FEBY?s special conditions.The purpose with the essay was to examine if it really is profitable to build small hoses aspassive houses.

Holmen Skog is currently using a GPS-program called TraktInfo, originally developed within the company. They are now planning to switch to a new GPSprogram or allowing the contractors to buy other programs available from the logging equipment manufacturers. To be able to offer this flexibility, Holmen Skog needs to obtain information about the features offered by the different manufacturers in their specific programs, and also when the manufacturers are planning to start selling programs adapted to the new standard called StanFord2010. According to the study, the manufacturers are hesitant to StanFord2010 and there has also been a lack of clear signals from the customers and clients about what kind of different new features to include in the programs. The feature most frequently used by forest machine operators today is the option to keep record of the harvester?s path by creating a ?log plot?. This feature was not used to its full potential however, since only one out of eight of the forwarders included in the study had computers that were compatible with the harvester?s computer.

ABB is one of the world?s leading engineering companies in power and automation technologiesand their solutions improve performance while lowering environmental impacts for energycompanies and industries. ABB FACTS designs equipment and plants for series and phasecompensation.This thesis has been performed at ABB FACTS on the Mechanical Design (DM) department inVästerås, Sweden. The purpose of the thesis was to develop and design calculations andsimulation tools for ABB FACTS?s standard series capacitor platforms.

This work covers a broad analysis of the risks that could impact the achievement of electrical safety of electrical installations. The work includes both electrical equipment such as the installation of electrical equipment.The report illustrates the main technical characteristics of electrical connections greater than 10 mm2 and provides an introduction to the crimping systems for copper and aluminum conductors. In addition to that analyzes the factors that are important to assure the quality of an electrical connection throughout the value stream in terms of both materials such informations. Furthermore analyzed deeper the need for skills development of technicians and other staff.The different parts of this work are analyzed and presented, in theory to studies carried out both at Elpress AB and partly with the help of other scientific reports dealing with similar subjects. In addition, presents a survey that will help understanding the current perception of the electrical connections and cable crimping systems among end users.

In the next few years the pollutants loading at the Slottshagen wastewater treatment plant in Norrköping is going to increase due to the reason that one of the waste water treatment plant in the district will be shut down.A survey of how these different pollutants are divided in the treatment process is therefore necessary for mapping out both the loading and treatment efficiency.This can be achieved by studying mass balances.Mass balances were carried out for the water treatment process for the mechanical/chemical,biological and the chemical stage.The mass balance studies show that the treatment efficiency was very good. However in order for the mass balances to be quite consistent and to ensure complete coverage of results and conclusions i.e. more reliable results, sludge samples should be collected and taken at different times per day and the influent rate should be investigated.In this work mass balance has been set up in order to illustrate and identify the factors that should be considered and taken care of for further estimation using mass balances in the future. Furthermore this survey results in a calculating model for the mass balances at thisplant.This calculating model is used as a tool to facilitate future calculations for mass balances for the water treatment process at Slottshagens wastewater treatment plant.Moreover it provides a basis for carrying out further estimation of the treatment process in the near future.In this project the importance of some operating parameters was also taken in consideration.This calculating model can be modified so that calculations of such operating parameters i.e. sludge loading and sludge age can be easily performed.Such information can be used further to evaluate different operation alternative in order to ensure an optimal use of the treatment process with in the plant..

Abstract Title: The Future of ABC at Sandvik Tooling ? Incorporating ABC with information systems in order to drive business development from a cost point of view. Authors: Jenny Andersson and Camilla Salomonsson. Supervisor: Charlotta Johnsson ? Department of Automatic Control, Lund University.

The Swedish energy company Vattenfall is currently the owner of the district heatingsystems in Nyköping and Motala. To be able to also offer cooling solutions tocustomers are becoming more and more important. This report describes the resultsof an investigation of the cooling market in the two cities and the potential needs forcooling today and in the coming 20 years. The total potential for the coming 20 yearsis estimated to be roughly 17 MW for Nyköping and 9 MW for Motala.Two possible district cooling systems for each of the two city centers was modeledand a comparison was made between different cooling techniques namely absorptionand compressor chillers.Absorption chillers driven with district heating during the summer is one way ofincreasing the load in a combined heat and power plant and thereby the possibleelectricity generation. The cost of heat production must be low for absorption chillerto be able to compete as an alternative.

To get the maximal output of your exercise in gym machines, there are different factorsto be considered. For example the strength of the muscle varies dependent on the positionof the muscles. To get the best results of the exercise the load has to reduce and increaseat specific positions.This study was made in cooperation with Caretaker Scandinavia AB, a company forsales, marketing and development in health care. They are general agent for Nordic Gymwho works with manufacturing of equipment and machines for gym and fitness.The aim of this study was to generate a method of measurement to evaluate and controlthe biomechanics of Nordic Gym´s workout equipment. A protocol for an ergonomicanalysis on the equipment has also been elaborated.One of the methods to measure the biomechanics was to measure the torque through thewhole movement.

The Göta älv-bridge is a welded steelbridge which is located in Gothenburg,it connects the inner city of Gothenburgwith the island Hisingen. Cracks wasdiscovered in the steel in 1999-2000which started an investigation of thebridge to clearify the condition of thebridge. The conclusion was a monitoringsystem based on laser light sent throughan optical fiber.This report describes the bridge, thedamages, the monitoring system and thetraffic on the bridge.Stefan Pup, at Vectura Borlänge was mysupervisor during this work. In myinvestigation the costs of themonitoring system and the costs ofclosing the bridge is compared andevaluated. The biggest investigatingpart is the costs of closing the bridge.The results of my investigations is thatclosing the Göta älv-bridge would cost 1107 300 SEK / day.

AbstractIt is important to choose which spare parts to keep in stock. With the right spareparts in stock the costs for inventory and production loss will decrease. Cavalieri et al. (2008) highlights that the balance between inventory cost and production loss is underestimated.  It affects the company and must be considered before decision on purchase.The problem with spare engines is that they are all more or less critical for the production. That can be a reason for why no previous research targeting engines and classification of with engine should be kept in stock has been found.

A third party access to district heating networks has been proposed in Sweden, to increase the competition on the district heating market. Such third party access could create opportunities for the agricultural sector as an energy producer. This study describes the technical, economical and environmental prerequisites for a farmer cluster to build and run a heating plant, fueled with local wood fuel. The heating plant in the described scenario is 8 MW and will supply a village of 1000 houses, and is fueled with wood chips exclusively. Supplying a heating plant with fuel puts high demands on the logistics, since there need to be a continuous flow of fuel. In the scenario, wood residues from felling and thinning is stored in stacks in the forest, and a few times a year chipped and transported to a storage area at the heating plant. In the study, an estimation of the profitability has been made by estimating the cost of the investment, personnel, operating and maintenance costs and costs for the fuel and ash handling.

Background: outsourcing is one of the most obvious and continuous trends that has been able to study during the past ten years and also has had a strong development in the industry. What consequences will follow from an extended outsourcing? Purpose: the study?s overall purpose is to investigate what possibilities and risks that can be connected to an outsourcing decision and how the order of the service will handle the risks. The study will also investigate what management philosophy that will be used and regulate the outsourcing relation and how the company?s strategy will affect the decision and how the process of outsourcing will look like.