This thesis is based on a case study for the real estate manager Mimer in Västerås. Mimer provides a great deal of this city?s rental apartments. Many of their buildings have ventilation systems with a type of heat-recovery called ?heatpipe?.

The Island of Öland has one of the best wind climates for land based wind power in Sweden. An objective for the Island is to become self sufficient using electricity from renewable source of energy such as wind. There is currently 55 MW capacity installed on the Island and it is estimated that grid congestion will occasionally occur if more than 135 MW was installed.The aim of this thesis is to investigate he possibilities for load management by smart charging of electric vehicles, EV. The definition of smart charging is that the charging is done to some extent with an ICT-system, (information and communication technology) that correlates wind electricity generation to the charging of electric vehicles. The purpose is to avoid grid congestions on the sub-sea cable that connects Öland to the mainland because that in turn would curtail wind energy production.

The importance of energy- and environmental issues has increased, and the work towards reducing carbon dioxide emissions plays a major part. The European Union has set up goals for the membership countries to work towards this to happen. The carbon dioxide emissions in Sweden have been reduced the last few years, but there is still a lot to do. About 30 per cent of Sweden?s carbon dioxide emissions generate from energy usage related to housing, this is why the housing sector is of interest to examine.

The heating of companies premises is today functional with electrical heating and heating offossil fuel. The energy cost for these kinds of heating in buildings has heavily increased duringthe last years and the influence on the environment has become more visual. This leads to thatenterprises today become more anxious to render energy more effective and find alternativesolutions to their ancient heating systems. This is something that Skandinaviska kraftprodukterAB in Halmstad has become aware of.The purpose with this examination is to find the most cost-efficient and environmental measuresfor the office and workshop premises of SKP AB. Where one of the bigger things is to find agood alternative for their current oil furnace, which was heating the workshop.

Hypothermia during anaesthesia is a well-known phenomenon that may cause several side-effects such as greater risk of postoperative wound infection and increased risk of heart complications. The most efficient way to avoid this is to prevent hypothermia from occurring. The aim of this paper was to compile the research on the most efficient way to prevent hypothermia during anaesthesia for cats and dogs, and to compare these results to how Swedish animal hospitals prevent hypothermia today. To investigate this, a survey was sent out to several animal hospitals around Sweden to see what methods they used to prevent hypothermia in their clinics. It is difficult if not impossible to prevent the body temperature from falling slightly when anaesthesia is induced because of the drug interactions in the body that follow from the drugs given. A 1-1,5°C decrease in body temperature is to be expected and is difficult to avoid.

Staden Sulaymaniyah ligger i den kurdiska delen av Irak och har på senare år utvecklats då många valt att flytta från landsbygden till den centrala delen av staden. Nybyggandet sker under tidspress och långsiktigt hållbara lösningar prioriteras inte. Målet är att ta fram ett hus som är anpassat för majoriteten av befolkningen och samtidigt få ett bra och energieffektivt inomhusklimat. En faktainsamling genomfördes för att ge bakgrundsinformation till projektet. Vidare gjordes en planlösning till huset i AutoCAD vilken har använts som grund till utformningen av huset och smarta lösningar.

Since the 19th century the concentration of CO2 in the atmosphere hasincreased by 40 percent as an effect of the use of fossil energy sources.Increased concentration of CO2 will likely lead to increased temperature,changes in precipitation, rising sea level and increased frequency of extremeweather like storm events. A step to reduce emissions of CO2 and mitigateclimate change, for the property of Tagel, can be to adopt new silviculturalstrategies and analyse which is the most effective. As a result of that, threescenarios was produced, business-as-usual (BAU), increased set aside landand energy. An introduction of windpower at Tagels estate (property) andeffects on carbon balance was also examined. By using the Heureka systemand LCA-analysis in this study, it showed that the scenario of increased setaside land was the most efficient way to reduce carbon dioxide (CO2)emissions for the analysed period of 100 years.

This master thesis is an in-depth study of an existing heating system at a household cooperative in Uppsala that has been converted from district heating to a bedrock heat pump system. The study focuses on an economical system optimisation of the building?s complete heating system. The aim was to determine how well a heat pump system in large buildings actually work, find out possible ways to optimize the existing system and point out important system parameters for new heat pump installations in larger buildings.The project points out a possible energy cost reduction of 45 % without investment and further cost reductions with equipment investments. A reduction by 30 % is possible by improvements in the regulation system and 15 % is possible by maintaining the brine system.

In the production of pulp, paper and cardboard, a large amount of water is used daily. The water has to be purified in the internal purifying plant before it reaches the receiving body of water. In the biological purifying stage at the Stora Enso Skoghall mill, an aerated basin is used where the microorganisms, using oxygen, oxidize the organic material to carbon dioxide. The air is pumped from the bottom of the basin and the oxygen can then be transported from the air bubbles to the water through diffusion. The problem with aeration of waste water from the forest industry is that wood residues, such as fatty acids, are making the transport of oxygen in water more difficult.

According to a decision of the European Commission, measures are to be taken to reduce the use of energy in the EU. The goal is to reduce it by 20 % compared to the current use. This shall be done to the year 2020 (European Commission, 2011). One industry that use large amounts of energy is the construction of buildings which account for almost a third of the energy use (Brogren, 2012). The major part of the energy that is used in the construction industry is not used when the buildings are built, but rather during the rest of their subsequent lifetime.

This thesis investigates how energy is used in three public baths today and suggests measures that could reduce the energy demand. The results show that there is a great poteltial for energy savings i public baths, and that it would be interesting to examine some of the proposed measures further..

Considering that the price and demand for energy gradually has risen over the past decade and a wider discussion about the human impact on the environment has become increasingly more important and given a clearer role in modern society. This has contributed to increased incentives to reduce the use of fossil fuels and increase the use of renewable energy.The agriculture currently accounts for 20 % of Sweden's total greenhouse gas emissions. A way for an agricultural company like Wapnö AB to reduce their emissions could be to utilize existing renewable energy sources within their own premises.The report's aim is to create an energy audit of Wapnö?s existing energy system and how it changes with a future biogas plant in operation. The energy audit is used to illustrate how the company?s climate footprint could change.

To achieve a sustainable development, three aspects have to take equal place in the society; environmental, economical and social. To reduce the impact on the environment and the amount of greenhouse gases supplied to the atmosphere, industrialized countries and less developed countries must start cooperating. Also the use of renewable energy sources, like solar, hydro and wind power, have to increase.Wind power has great potential as a future energy supply. It is cost efficient, quickly developed and the resource is abundant and available worldwide.Examinations made in Sweden, indicates that there are difficulties establishing wind power at the same pace as the environmental goals, set by the Swedish government, requires. Mainly because people living nearby potential areas for wind power farms, appeal against the decision.This study aims to investigate differences between how people in Sweden and Brazil look at wind power as a future energy source and at the establishing process.

In the production of pulp, paper and cardboard, a large amount of water is used daily. The water has to be purified in the internal purifying plant before it reaches the receiving body of water. In the biological purifying stage at the Stora Enso Skoghall mill, an aerated basin is used where the microorganisms, using oxygen, oxidize the organic material to carbon dioxide. The air is pumped from the bottom of the basin and the oxygen can then be transported from the air bubbles to the water through diffusion. The problem with aeration of waste water from the forest industry is that wood residues, such as fatty acids, are making the transport of oxygen in water more difficult.

The basis of the study lies with a newly patented gearbox by cardiologist and inventor Stig Lundbäck. Stig founded CorPower Ocean AB to further develop the gearbox to be used in a wave energy device. The purpose of this project is to develop a concept of a lifting system with CorPower Oceans gearbox that is more energy efficient than a hydraulic lifting system. The goal is to use technology from CorPower Oceans gearbox inversely to perform heavy lifting as an alternative to hydraulics. The project is limited to applying the gearbox and gear rack on a forklift with a lifting capacity of ten tons.The main tool in this project will be the product development process Systems Engineering where only the most relevant parts will be used to develop a concept.