The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

How to use automatically read data to create a method that visually describes how energy is used in a building, the so called energy signature..

Solar energy is the one most talked about among energy sources due to its huge potential amongst renewable energy technologies. A greater use of the solar energy may be the solution to today's climate threats. Normally there are two different types of solar technologies, solar cells and solar thermal collectors. Solar cells convert solar energy in to electricity whilst solar thermal collectors convert solar energy into heat, which can be used to heat hot water for households. This goal of this study has been to investigate the possibility of implementing solar energy into the energy system of Kista Galleria, one of Sweden's foremost venues.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

In today?s society a large focus is put on energy systems and how our energy systems are built up. In order to make sure that we in the future still can enjoy the living standards that we are used to today, Sweden and EU have made a number of decisions on making our energy system more energy efficient and consequently reduce the usage of energy resources. By 2020 the European Union should have reduced its energy consumption by 20 % compared to 1990?s level, and by 2050, 50%.

The project was intended to produce a brush simulation plugin to the image processing program GIMP which would use a 6DOF drawing tablet for user input.Too ambitious goals coupled with compability issues between the resources used resulted in that no meaningful software was produced. Experience was however obtained, and this paper is intended to give an overview of relevant concepts for- and the process ofcreating a brush simulation..

The energy consumption in the sectors of residential and public buildings is 40 % of the total energy consumption in Sweden. The main part, 85 %, of the energy use in these sectors is for operation of the buildings. The rest is used in the building process. When energy-efficiency measures are taken the energy use during the operation time decreases and the fraction of energy consumption during the building time increases. This project is carried out in cooperation with JM AB and concerns the energy use during the building time of production of blocks of flats at the building site.The main part of the electricity that is used during the production of apartment buildings goes into the heating of portacabins and illumination of the building during the construction phase.

The Energy Performance Certification in Sweden was developed as a tool to achieve the Government's target to reduce Sweden's energy consumption by 20 percent by 2020. The Energy Performance Certificate has previously received some criticism for not fulfilling its purpose. Questions that formed the basis for this report is how the energy performance certification provides support to buyers of single-family houses and if the energy performance improved in terms of reliability. The report begins with a background description that describes how the energy declaration works and some of the findings of previous evaluations and surveys. A survey to investigate the broker's position to energy performance have been conducted as well as interviews with buyers and sellers of houses. An investigation whether the energy performance can vary between different calculation programs, depending on various assumptions made by the energy declarant, has been made.Brokers and sellers have proved negative attitudes towards energy performance, particularly brokers.

SAMMANDRAGHistorisk Simulation, Delta-Normal och RiskMetrics prestation utvärderas med hjälp av Kupiecs Backtest. Value at Risk (VaR) beräknas med tre olika konfidensnivåer utifrån Affärsvärldens Generalindex och HSBC kopparindex. Utifrån överträdelser från verkligt utfall undersöks vilken VaR-modell som estimerar marknadsrisken bäst. VaR-modellernas prestation jämförs, och i analysen utreds hur konfidensnivå och tillgångars egenskaper påverkar VaR-modellernas prestation. Resultaten visar att Historisk Simulation presterar bättre än Delta-Normal och RiskMetrics på den högsta konfidensnivån vilket troligtvis beror på att RiskMetrics och Delta-Normal antar normalfördelning.

Calculated and measured energy in residential buildings is going to differ. The reason to this may be due to many factors. In this study there is a study on how these factors affect the energy use in a building. To get an insight in what defines energy, there is first a description of energy supply both worldwide and used in Sweden, followed by a description of the energy balance. In this study energy will be studied in residential buildings only.

Rising energy prices and higher energy demands have led to an increased focus on energy efficiency, in particular in the real estate business, where high potential for energy savings exists. Within the next few years, buildings that were constructed in the sixties and seventies will be in need of renovation. One of the challenges of these renovations will be to improve energy efficiency. A real estate company that is facing this challenge is Uppsalahem AB, based in the city of Uppsala, Sweden. This study focused on analyzing energy efficiency measures when renovating old buildings.

AbstractThe Energy Declaration is a law that will come into effect October 1: Th 2006. This report has Värnamo municipality as principal and shall clarify what the estate owner in general and Värnamo municipality in particular need to know about this law. Another part that is going to be dealt with is how large the future need for energy experts in this field will be, and which competence that will be demanded for them.The work will in general deal with simplified energy declarations for apartment houses and public buildings, since these buildings are the first to be involved with energy declarations.The energy declaration will consist of a number of important components.? Energy power i.e. how much energy the building consume? If the ventilation control is done? If the radon measurement is carried out? Recommendations of measures to improve the energy power? Reference value to compare the buildings energy power againstAccording to the law the declaration shall been made by an independent expert, which will need certain information for this.

In this master?s thesis the problem of simulating conditional Bernoulli distributed stochastic variables, given the sum, is considered. Three simulation methods are considered, namely the acceptance/rejection technique, Bondesson?s method and the Markov chain Monte Carlo method.To compare the three methods the bias and the standard deviations of the simulated variables are evaluated. The results of the simulation study shows that the Markov chain Monte Carlo method is not the best method for this type of simulation.

The building and plant sectors represent a large part of Sweden?s energy use. Putting energy requirements in public procurement as a tool for reducing energy consumption in the building and plant sectors is therefor an opportunity that operators can take advantage of. The aim of this thesis was to map the energy requirements in procurement that operators in the public sector use today in building and plant projects. The analysis was made with respect to if the energy requirements corresponded to the parts with large energy use in building and plant projects and also in which way energy requirements in procurement are written in the contract.

Indoor Energy is a company that works in the energy sector. It works through itsthree subsidiaries Indoor Energy Services, Indoor Energy Control and Indoor EnergyConsultants. Because of their comprehensive experience and offering of broad rangeof services they can contribute to integrated extensive solutions for their customers.Indoor Energy Control works with building management through control andregulation. This work is realigned by programmers and project managers. Working inthis area is complex and places a great demand on both technical innovation andprofessional project management.Due to the complexity of the work Indoor Energy Control has a hard time to get thenew employees to be independent in their work as a programmer.