Summary Today energy prices are rising. As a result biomass fuel is getting more and more interesting. Wood chips is very popular, but also straw from grain production is on the table. Lunds Energi AB project a combined power and heating plant in Örtofta out of Lund. Wood chips is meant to be the main energy source, complemented by straw. In this thesis the transportation of straw for fuel is studied.

The aim of this study about wind power planning in forest was to examine the factors and restrictions, which represent technical limitations, biodiversity, tourism and amount of energy for wind farms in Kronoberg County. Suitable areas for wind power were identified from the collected information about planning principles and potential conflicts. From the suitable areas the potential energy gain is calculated. Methods used were mainly a literature review, interviews with experts and practitioners, GIS analysis and a rough calculation of the energy gain. The section of information and facts describes in general wind power planning and possible conflicts.

BakgrundSvensk sjukvård har idag bland de bästa behandlingsresultaten i Europa, men trots det förs diskussionen om sjukvården ofta i negativa ordalag. I ett försök att förbättra synen på verksamheten och bli mer effektiva har sjukvården i Sverige ofta använt sig av kommersiellamodeller, modellerna har dock behövt anpassas för att fungera i sjukvårdens miljö. En av de senaste kommersiella modellerna som nu införs i den svenska sjukvården är Lean Healthcare,som är sjukvårdens version av Toyotas produktionsfilosofi Lean Production. En stor del avtidigare forskning på området har behandlat Lean Production men lite finns att tillgå som handlar om Lean Healthcare. Den här studien är ett bidrag till att utöka kunskapen om Lean Healthcare i Sverige.SyfteSyftet med den här studien är att beskriva hur Lean-filosofin fungerar i den svenska sjukvården samt att göra en jämförelse mellan Lean Production och andra kommersiella modeller som tidigare har införts i den svenska sjukvården.GenomförandeMed hjälp av intervjuer på tre svenska sjukvårdsenheter har en fallstudie med fokus på Lean Production och Lean Healthcare genomförts.ResultatResultatet av studien visar att Lean Healthcare, i likhet med tidigare modeller, har krävt anpassningar för att fungera i sjukvårdens kontext.

This report is about the issue with decreasing production rate mainly caused by failuresrelated to the multiswitch. The multiswitch is a machine at Gefleortens Mejeriföreningwhich has the function of distributing milk cartons from one incoming track into fiveoutgoing tracks. Milk cartons who gets stuck and there by causes the production to stop,is the mainly problem with this constructionThe purpose with this report is to understand the causing factors and make suggestions which can help solving these factors. By analyzing the machine during production, having contact with different suppliers, searching internet for information, 3d-cad drawings and the complementary with personal experiences, this machine has  been evaluated and as a result of this new problem has come to be known.The discovered problems was analyzed and resulted in new suggestions for alternative options. Later the most functional results was chosen and put as a suggestion for the new model.A new machine built with the suggestions from this report assures to be well adapted to the environment at Gefleortens Mejeriföreing and the problems it causes..

The Swedish energy companies have several different systems for data collection of the energy consumption of their clients. Often computerized remote meter readers are put in practice in order to register the energy consumption of large companies. The majority of household clients, however, are read off by the assistance of manual methods. Household power consumption is read off once a year. As a result, these clients are not debited for their actual consumption; their invoices during the year are the result of estimations. At times when the electricity supply system is highly loaded, electricity is more expensive.

The production costs have steadily increased within the construction industry during the 21st century. Voices are raised meaning that the construction industry is too unsuccessful in making the production more efficient and to develop it?s way of working. One way to deal with the production costs is to minimise the waste, with waste meaning activities that doesn?t add value to the finished product.

In recent years, moisture damages have been noticed in rendered, undrained stud walls. The design is built on the principle one-stage tightening which means that there is no air gap in the construction. The damages have occurred when water has permeated through the rendering in leaking connections and fittings for windows, doors, canopies, balconies, terraces and awnings. Behind the plaster carrier, which consists of either polystyrene or rigid mineral wool, plasterboard has often been used as a wind protection barrier. In many cases the wind protection barrier and the underlying wooden studs have been exposed to mould and in some cases even rot.

This Master degree project has been performed at the Braviken paper mill on papermachine 53 (PM53) which produces newsprint paper. The current economic situationhas contributed to declining demand for newsprint, which means it is extra important tobe competitive by high energy efficiency. Particularly as energy prices are expected torise when the economic growth returns.One way to increase energy efficiency is by reducing the water use in paper and pulpmills and consequently save energy through reduced heating of water. The thesis's maintask is to evaluate whether a water purification plant (microflotation plant) forpurification of process water in PM 53 is profitable. The microflotation plant enablesreuse of warm process water instead of losing the energy to receiving waters.

The use of energy is an important question in today´s society, and a substantial part of the energy that is used today is used in our homes. To lower this usage is vital, and there are regulations in place both on the national and the local level, that say that new apartment blocks must be built to consume less energy, which in the end will lower the impact on the climate.One way to make the housing sector more environmentally sustainable, is to produce energy issions that are bad for the environment, for example to build wind turbines close to or even on the buildings, so called urban wind power. The scope for this report is to see if urban wind power could be a sustainable alternative for the residential area that Svenska Bostäder plans to build in Albano in Stockholm.There are extensive scientific theories regarding wind and wind power, and a literature study is made to investigate past knowledge in the area. Efforts have been made to find earlier trials with urban wind power and, both scientific research and trials where urban wind power actually has been installed. The theory chapter deals both with the wind itself and how electricity can be generated from wind.

Mechanical ventilation is the most common type ofventilation in newly constructed office buildings. Therehas been an interest to utilize natural ventilationinstead of mechanical ventilation among architects andHVAC consultants in recent years. This is due to thesize of mechanical ventilation systems, which arespace consuming. The mechanical ventilation system isalso complex and requires maintenance. Furthermore,the fan uses a considerable amount of energy.

Water is an essential factor for both people and animals, and access to water is therefore of great importance. The water access also largely determines the availability of food for people and feed for animals. The aim of this study was to survey the affect of water access on milk production from dairy animals. The study included nineteen farm visits that were made in the Nyando district in Kenya between February and Mars 2011. Farm visits included interviews with questions about for example number of dairy animals, milk production, water access, feed and water routines.

Grubbe Ventilation AB is a sheet metal and ventilation company who provides design, installation, service, and repair of ventilation. The company is expanding their business by building a new facility in Umeå, Västerbotten. The property is designed to be used for both office and industrial work.Grubbe Ventelation AB has not yet decided upon wish system which is to be established to provide the building with heating and cooling. The consulting firm Umeå Projekt Team has therefore been asked to investigate the possibilities to invest in geothermal- heating and cooling.If the investigation of a geothermal heating- and cooling system would provide favorable results it would be a very appropriate alternative that provides energy at low costs and are an environmentally friendly option as the energy comes from stored solar energy in the ground is provided by stored solar energy in the ground.The facility ´s heating and cooling consumptions are calculated in the program BV2 and the result indicate a heating demand of 185 000 kWh per year due to thermal transmittance, transmission losses, heating of warm water and a cooling requirement of 5500 kWh.Three different systems of geothermal heating and cooling were tested in the computer program Energy Earth Design. The results show no difference in the dimensioning of the drill hole if merely heating were to be used or both heating and cooling were to be established.

With higher prices for oil and increased focus on fossil fuels impact on the environment the heating sector are searching for alternative fuels. Pellets are a quite new product whose production has risen exponential in recent years. Today there are small-, medium-and large-scale users, where the large-scale consumers are the heating sector. The heating sector is mainly using oil to cover the increased demand during cold periods. The purpose of this study is to analyze the potential of pellets if it would replace thermal power plants oil and coal. The study will also analyze the economic impact a conversion would mean for a heating plant and if the pellet is a reasonable substitute. 2008 statistics from the Swedish district heating association were analyzed and a calculation was performed to determine how many tons of pellets is needed to replace coal and oil.

This examination work is performed at the institution of industrial economy and production at Jonkoping technical university, for JELD-WEN Door Solutions plant in Forserum.Today the focus in the company is on to reduce their inventories binding of capitals as well as inventory of products and that includes to get a good control of the supply and handling of material which is of great importance.JELD-WEN Door Solutions is one of the worlds leading producers of windows and doors and the head-office is located in Oregon, USA.A great number of wooden doors are manufactured by the company in varying of constructions, classifications and performance.The production of the plant in Forserum has a project- and customer focus manufacturing where only internal doors are produced. The overall market they are concentrated on is to different institution such as schools, hospitals etc.The purpose of this work is to investigate possibilities to improvement of material- and production control at JELD-WEN. The report will handle the master production schedule to and from the production divisions within manufacturing industry. Focus will be on the way for information- and material flows from arrival, transport within the company and further on to customers.Further a map of the flow was performed which gave a clearer picture of the connection between the flow of information- and material for the manufacturing process. On the basis of the mapping of the flow, the group discovered that the flow of material had some improvement potential.

Konkurrensen i tillverkningsfo?retag o?kar sta?ndigt och detta medfo?r att det sta?lls ha?rda krav pa? produktkvalitet och fo?rma?gan att leverera produkter i tid. Fo?r att fo?retag ska kunna na? upp till dessa ma?l kra?vs utveckling och sta?ndiga fo?rba?ttringar i takt med den va?xande marknaden. Detta uppna?s pa? olika sa?tt men ett vanligt sa?tt a?r att arbeta med fo?rba?ttringsmetodiker.