A new FPGA suitable for space applications has just reached the market. To investigate whether there are any possible flaws or limitations similar to those previously seen on FPGAs, an evaluation has to be done. This master thesis contains the evaluation of this new radhard FPGA with focus on possible design limitations and package related electrical phenomena.Areas evaluated: Ground-/VDD bounce, Cross talk, Rise time sensitivit, Power cycling, Power consumption, Place and route tool, Radiation hardnessThis report contains all steps in the evaluation. From method to measurements, comparisons, theory, results and conclusions. In the evaluation work, special effort has been made to develop designs that really stress the FPGA to find potential problems.

With background in the rapidly growing need to find solutions for sustainable energy production and the increasing interest for wind power, this report was written. With take-off point from the wind power plant Big Glenn, which has been built in the harbour of Gothenburg, a model of the adjacent power grid has been created in Simulink/SimPowerSystems. Parameters for the power grid and its components has been provided by Göteborg Energi Nät, that has also been the supplier of measurement data of produced power, the power need from loads in the vicinity, voltage levels, current values and also the variation of power factor at the wind power plant.The SimPowerSystems model has been used to perform simulations of power flow in the grid. These simulated values have then been compared to the measured values to verify the functionality of the model. Further, the model has been used to perform simulations of a grid fault, which causes a voltage drop.

This bachelor thesis aims at investigate how a specified house can optimize its energy consumption.Today the house often stands for the major part of the energy consumption in a consumers? life,whereas an energy optimization creates economic as well as environmental advantages. It is importantto make old houses more energy efficient, but putting high energy demands on new houses could beargued to be more important. The installations functions as both the heart and brain in a house, thusmaking it important to energy optimize these. Since the background describes the importance ofenergy efficiency and optimization in a house, the focus area of this report will be an investigation ofdifferent types of heating systems in order to be able to choose the one most suited for the house.Aspects considered when choosing the heating system was how economic the system is both inservice- and investment costs and how environmental and operational friendly the system is.Through literature reviews there were sufficient information gathered that served as a foundation whencomparing and choosing between the four systems - district heating, pellet-fired boiler, geothermalheating and solar heating.

The examination has been performed at Bjerking AB, which is an architectural and engineering company. Bjerking AB has the ambition to be a member of Green Building.The Green Building program developed in year 2005 by The European Commission, the program is an environmental system with the aim to improving energy efficiency within the sectors of non-residential buildings. The minimum requirements to participate the program are following: in new-built buildings the calculated energy consumption must be 25 % lower than the requirements in the BBR (Building regulations) and in refurbishment the reduction must be 25 % lower than before the optimization.The aim of this study has been to examine and review the company Bjerking AB's energy efficiency work in the project of building the school/kindergarten S:ta Maria Alsike, where the goal is to get this building Green Building classed. A description of requirements to become a member of the Green Building has also accomplished in the thesis.The methods performed in this study are literature review, searches on the Internet, studies on the project database for facts/values, calculation of energy consumption and interviews of members of the Green Building. The following issues have been dealt with in the report;-          Did the building in the project manage the requirement to achieve an   energy consumption that is 25% lower than the requirements in BBR?-          What technical measures/system was selected in the building?-          What kind of cooperation was the project based on?-          What is required for consultancy companies and real estate owners to become members of the Green Building?The study of the project and calculation of estimated energy consumption in the building, give the result 47 kWh/m2, year.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey wasperformed. The voltages and currents have continuously been sampled in the incoming 10 kVsubstation HSP01 from April-August 2008. Power quality measurements were also performedin Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of theinduction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps tothe plant. The reason for the latter measurement was due to registered negative transients eachtime the motor was connected to the grid. The cause of the transients could be explained by thecoupling in the substation, the ageing of the motor which could result in damage of thebearings or resonance in the motor circuit which amplifies high frequency harmonics.

The government regulations for energy use in buildings will be tightened in the future. At the same time the interest in environmental classifications and certifications of buildings is increasing. This has meant a new situation for solar energy. The designs of solar heating systems are often based on experience and/or rules of thumb, rather than calculations and simulations. This thesis examines whether simulation tools, in this case Polysun, are useful in this work.

There's no doubt today that mankind has contributed to the changing climate byher use of fossil fuels. This must change in the nearby future. The Europeanleaders are expressing concern that renewable energy sources are not beingused to their full potential. The 2001/77/EC Directive on Electricity Productionfrom Renewable Energy Sources was accepted in 2001 to encourage thedevelopment of energy production from renewable sources, which isconsidered a step towards the fulfillment of the goal of the Union, that 12% ofthe gross energy consumption should come from renewable energy sources bythe year 2010.The objective of this thesis is to illuminate the common legislation of the EUregarding renewable energy with regard to goal fulfillment, judicial quality,conflicts with other goals of the EU and other faults. The objective is reachedby a hermeneutic study in which interpretation of written text is the mainmethod.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey wasperformed. The voltages and currents have continuously been sampled in the incoming 10 kVsubstation HSP01 from April-August 2008. Power quality measurements were also performedin Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of theinduction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps tothe plant. The reason for the latter measurement was due to registered negative transients eachtime the motor was connected to the grid. The cause of the transients could be explained by thecoupling in the substation, the ageing of the motor which could result in damage of thebearings or resonance in the motor circuit which amplifies high frequency harmonics.

This thesis has been carried out at the Department of Urban and Rural Development at SLU Ultuna during the spring semester 2009. The topic of the paper is how energy consumption can be influenced through design and if the conditions for good design decreases when solutions based on energy efficiency are used. The report is divided into one literature study and one part where energy efficient solutions are used in a design. The thesis work has its origin in a project called "Energihus i Uppsala." The planned building will be a center for energy research in Uppsala. The project aims to demonstrate to the public what is currently happening in research related to energy.

According to a decision of the European Commission, measures are to be taken to reduce the use of energy in the EU. The goal is to reduce it by 20 % compared to the current use. This shall be done to the year 2020 (European Commission, 2011). One industry that use large amounts of energy is the construction of buildings which account for almost a third of the energy use (Brogren, 2012). The major part of the energy that is used in the construction industry is not used when the buildings are built, but rather during the rest of their subsequent lifetime.

Geothermal energy can be extracted from an aquifer, where the groundwater is used as heatexchange medium while heat and cold are stored in the surrounding material in the aquiferand to some extent in the groundwater. Application of aquifer storage for the use ofgeothermal energy is mainly used in large scale facilities and is limited to sites with suitableaquifers in the form of ridges, sandstone and limestone aquifers.Löwenströmska hospital in the municipality of Upplands Väsby, north of Stockholm, islocated nearby the northern part of the Stockholm esker. This means that it can be profitableand environmentally beneficial for the hospital to examine the possibilities of aquifer storagein the esker material next to its property.The purpose of this master thesis has been to investigate if geothermal energy storage with aseasonal storage of heat and cold can be applied within Löwenströmska hospital?s propertyarea using groundwater modeling. A hydraulic groundwater model was constructed inMODFLOW based on a simplified conceptual model of the groundwater system.

The government regulations for energy use in buildings will be tightened in the future. At the same time the interest in environmental classifications and certifications of buildings is increasing. This has meant a new situation for solar energy. The designs of solar heating systems are often based on experience and/or rules of thumb, rather than calculations and simulations. This thesis examines whether simulation tools, in this case Polysun, are useful in this work.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey wasperformed. The voltages and currents have continuously been sampled in the incoming 10 kVsubstation HSP01 from April-August 2008. Power quality measurements were also performedin Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of theinduction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps tothe plant. The reason for the latter measurement was due to registered negative transients eachtime the motor was connected to the grid. The cause of the transients could be explained by thecoupling in the substation, the ageing of the motor which could result in damage of thebearings or resonance in the motor circuit which amplifies high frequency harmonics.

Allmänheten har en stor efterfrågan av produkter inom området för hemautomation. Den senaste bluetoothstandarden Bluetooth Low Energy skapar nya möjligheter för intressanta produkter som underlättar vardagen. Lösningar som IR och Wi-Fi ger inte de förutsättningar som krävs för att på ett energisnålt och praktiskt sätt erbjuda sådana produkter, något som Bluetooth Low Energy gör. I denna rapport diskuteras standarden i syfte att redogöra för hur den kan användas för att automatisera ett hem.För detta examensarbete implementerades en strömbrytarprototyp och en iOS-applikation, vilka användes för att unders öka och påvisa ett koncept för hur tekniken kan tillämpas för hemautomation. Resultaten visar att teknikens räckvidd är dess främsta begränsning.

In today?s fast growing and closely connected society, a reliable and energy efficient transportation system is more than ever desirable. Nowadays the significant part of the transportation sector?s energy demand is supplied by fossil fuels.Improving energy efficiency in combustion engines will result in reduction of fuel consumption and CO2 emissions. A modern internal combustion engine has an efficiency of 30-45 %, where the most energy loss occurs as result of heat losses in the exhaust and cooling systems.